mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Imre Kaloz <kaloz@kernel.org>
To: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org, linux-kernel@vger.kernel.org,
	Andrew Lunn <andrew+netdev@lunn.ch>,
	"David S. Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	netdev@vger.kernel.org
Subject: [PATCH 20/38] net: ethernet: sgi: ioc3-eth: apply the DMA attributes only to 64-bit addresses
Date: Thu,  1 Oct 2026 18:11:55 +0200	[thread overview]
Message-ID: <42a71ea9aa16afdeb230d4d8c61c33cc055f2a28.1790857966.git.kaloz@kernel.org> (raw)
In-Reply-To: <cover.1790857966.git.kaloz@kernel.org>

A Bridge 64-bit direct-mapped DMA address carries the target widget and
the DMA attributes. An address in a bridge's 2GB 32-bit direct window
carries neither, so attributes OR-ed onto one form a 64-bit address
aimed at widget 0, and every receive raises a PCI error.

Apply the attributes, and the RX barrier's upper address bits, only to
64-bit addresses, in preparation for driving an XBridge through its
32-bit window.

Signed-off-by: Imre Kaloz <kaloz@kernel.org>
---
 drivers/net/ethernet/sgi/ioc3-eth.c | 24 +++++++++++++++++++++---
 1 file changed, 21 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/sgi/ioc3-eth.c b/drivers/net/ethernet/sgi/ioc3-eth.c
index 009f37105eaf..8702dfdf4c36 100644
--- a/drivers/net/ethernet/sgi/ioc3-eth.c
+++ b/drivers/net/ethernet/sgi/ioc3-eth.c
@@ -152,19 +152,37 @@ static inline int ioc3_alloc_skb(struct ioc3_private *ip, struct sk_buff **skb,
 }
 
 #ifdef CONFIG_PCI_XTALK_BRIDGE
+/* A Bridge 64-bit direct-mapped DMA address carries the target widget in
+ * bits 63:60 and the DMA attributes below it.  An XBridge is driven through
+ * its 32-bit direct window instead, where an address carries neither, so
+ * attributes OR-ed onto one form a 64-bit address aimed at widget 0.
+ */
 static inline unsigned long ioc3_map(dma_addr_t addr, unsigned long attr)
 {
+	if (!(addr & PCI64_ATTR_TARG_MASK))
+		return addr;
+
 	return (addr & ~PCI64_ATTR_BAR) | attr;
 }
 
-#define ERBAR_VAL	(ERBAR_BARRIER_BIT << ERBAR_RXBARR_SHIFT)
+/* The RX barrier's upper address bits follow the same form. */
+static inline u32 ioc3_erbar(dma_addr_t addr)
+{
+	if (!(addr & PCI64_ATTR_TARG_MASK))
+		return 0;
+
+	return ERBAR_BARRIER_BIT << ERBAR_RXBARR_SHIFT;
+}
 #else
 static inline unsigned long ioc3_map(dma_addr_t addr, unsigned long attr)
 {
 	return addr;
 }
 
-#define ERBAR_VAL	0
+static inline u32 ioc3_erbar(dma_addr_t addr)
+{
+	return 0;
+}
 #endif
 
 static int ioc3eth_nvmem_match(struct device *dev, const void *data)
@@ -727,7 +745,7 @@ static void ioc3_init(struct net_device *dev)
 	readl(&regs->emcr);
 
 	/* Misc registers  */
-	writel(ERBAR_VAL, &regs->erbar);
+	writel(ioc3_erbar(ip->rxr_dma), &regs->erbar);
 	readl(&regs->etcdc);			/* Clear on read */
 	writel(15, &regs->ercsr);		/* RX low watermark  */
 	writel(0, &regs->ertr);			/* Interrupt immediately */
-- 
2.47.3


  parent reply	other threads:[~2026-10-01 16:13 UTC|newest]

Thread overview: 41+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-10-01 16:11 [PATCH 00/38] MIPS: SGI-IP27: add support for the IP35 (Bedrock hub) machines Imre Kaloz
2026-10-01 16:11 ` [PATCH 01/38] MIPS: Xtalk: guard the widget identification table from assembly Imre Kaloz
2026-10-01 16:11 ` [PATCH 02/38] MIPS: SGI-IP27: dump the NMI save areas the CPU scan recorded Imre Kaloz
2026-10-01 16:11 ` [PATCH 03/38] MIPS: SGI-IP27: add REMOTE_HUB_PI_S()/REMOTE_HUB_PI_L() Imre Kaloz
2026-10-01 16:11 ` [PATCH 04/38] MIPS: SGI-IP27: detect Bedrock hubs at boot Imre Kaloz
2026-10-01 16:11 ` [PATCH 05/38] MIPS: SGI-IP27: widen Kconfig for the Bedrock-based machines Imre Kaloz
2026-10-01 16:11 ` [PATCH 06/38] MIPS: SGI-IP27: fold the dead SN1 arm out of klconfig.h Imre Kaloz
2026-10-01 16:11 ` [PATCH 07/38] MIPS: SGI-IP27: choose the node address layout at runtime Imre Kaloz
2026-10-01 16:11 ` [PATCH 08/38] MIPS: SGI-IP27: add the Bedrock hub register windows Imre Kaloz
2026-10-01 16:11 ` [PATCH 09/38] MIPS: SGI-IP27: decode a Bedrock hub's node id and system size Imre Kaloz
2026-10-01 16:11 ` [PATCH 10/38] MIPS: SGI-IP27: put a Bedrock hub's boot CPU in slot 0 Imre Kaloz
2026-10-01 16:11 ` [PATCH 11/38] MIPS: SGI-IP27: lay out node memory in 1GB banks on Bedrock hubs Imre Kaloz
2026-10-01 16:11 ` [PATCH 12/38] MIPS: SGI-IP27: reserve the bottom 64MB of node 0 " Imre Kaloz
2026-10-01 16:11 ` [PATCH 13/38] MIPS: SGI-IP27: route interrupt masks and slices through both PIs Imre Kaloz
2026-10-01 16:11 ` [PATCH 14/38] MIPS: SGI-IP27: address a CPU's own PI for NMI, IPI and RT counter Imre Kaloz
2026-10-01 16:11 ` [PATCH 15/38] MIPS: SGI-IP27: take a CPU's node from the CPU table in per_cpu_init() Imre Kaloz
2026-10-01 16:11 ` [PATCH 16/38] MIPS: SGI-IP27: resolve the mapped-kernel node shift at runtime Imre Kaloz
2026-10-01 16:11 ` [PATCH 17/38] MIPS: SGI-IP27: load the kernel at node offset 0x40000 Imre Kaloz
2026-10-01 16:11 ` [PATCH 18/38] MIPS: SGI-IP27: xbow_probe(): recognize KLTYPE_PBRICK_XBOW Imre Kaloz
2026-10-01 16:11 ` [PATCH 19/38] MIPS: ip27_defconfig: enable the IOC3 MFD, its cell drivers and tg3 Imre Kaloz
2026-10-01 16:11 ` Imre Kaloz [this message]
2026-10-01 16:11 ` [PATCH 21/38] MIPS: SGI-IP27: route XBridge and PIC DMA through the 32-bit window Imre Kaloz
2026-10-01 16:11 ` [PATCH 22/38] MIPS: SGI-IP27: recognize the PXBow crossbar Imre Kaloz
2026-10-01 16:11 ` [PATCH 23/38] MIPS: PCI: xtalk-bridge: recognize the PIC widget's 64-bit-only registers Imre Kaloz
2026-10-01 16:11 ` [PATCH 24/38] MIPS: PCI: xtalk-bridge: match PIC's register-level differences Imre Kaloz
2026-10-01 16:12 ` [PATCH 25/38] rtc: m48t35: support the SGI IP35 timekeeper's 1968 year base Imre Kaloz
2026-10-01 16:12 ` [PATCH 26/38] mfd: ioc3: add support for IOC4 Imre Kaloz
2026-10-01 16:12 ` [PATCH 27/38] MIPS: SGI-IP27: dispatch the early console between IOC3 and IOC4 Imre Kaloz
2026-10-01 16:12 ` [PATCH 28/38] MIPS: SGI-IP27: add L1 system controller support Imre Kaloz
2026-10-01 16:12 ` [PATCH 29/38] MIPS: SGI-IP27: wire the L1 into reset and the Ethernet address Imre Kaloz
2026-10-01 16:12 ` [PATCH 30/38] MIPS: PCI: xtalk-bridge: take the board part number from the L1 Imre Kaloz
2026-10-01 16:12 ` [PATCH 31/38] mfd: ioc3: add IP34 system-board entry to ioc3_infos[] Imre Kaloz
2026-10-02 10:02   ` Lee Jones
2026-10-02 10:29     ` Imre Kaloz
2026-10-01 16:12 ` [PATCH 32/38] net: ethernet: sgi: ioc3-eth: fall back to the platform MAC address Imre Kaloz
2026-10-01 16:12 ` [PATCH 33/38] MIPS: SGI-IP27: don't register a w1 master on an XBridge or PIC Imre Kaloz
2026-10-01 16:12 ` [PATCH 34/38] MIPS: SGI-IP27: report a Bedrock machine as SGI IP35 Imre Kaloz
2026-10-01 16:12 ` [PATCH 35/38] MIPS: SGI-IP27: identify the machine by the L1 brick type Imre Kaloz
2026-10-01 16:12 ` [PATCH 36/38] MIPS: SGI-IP27: register the Odyssey graphics widget Imre Kaloz
2026-10-01 16:12 ` [PATCH 37/38] MIPS: SGI-IP27: take the console from the KLCONFIG header on IP35 Imre Kaloz
2026-10-01 16:12 ` [PATCH 38/38] MIPS: SGI-IP27: give each CPU its own topology package id Imre Kaloz

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=42a71ea9aa16afdeb230d4d8c61c33cc055f2a28.1790857966.git.kaloz@kernel.org \
    --to=kaloz@kernel.org \
    --cc=andrew+netdev@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=edumazet@google.com \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mips@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    --cc=tsbogend@alpha.franken.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®