[PATCH 17/38] MIPS: SGI-IP27: load the kernel at node offset 0x40000

[Imre Kaloz <kaloz@kernel.org>]

A Bedrock machine's PROM owns node memory below offset 0x40000. Link
both the mapped and the unmapped kernel there instead of at 0x1c000.
On an Origin 200/2000 the kernel moves up by 144KB, and the 144KB
below it stays reserved and unused.

Signed-off-by: Imre Kaloz <kaloz@kernel.org>
---
 arch/mips/include/asm/mach-ip27/kernel-entry-init.h |  2 +-
 arch/mips/include/asm/sn/mapped_kernel.h            |  6 +++---
 arch/mips/sgi-ip27/Platform                         | 11 ++++++-----
 3 files changed, 10 insertions(+), 9 deletions(-)

diff --git a/arch/mips/include/asm/mach-ip27/kernel-entry-init.h b/arch/mips/include/asm/mach-ip27/kernel-entry-init.h
index 1bedd3c3bc58..958f4b390df8 100644
--- a/arch/mips/include/asm/mach-ip27/kernel-entry-init.h
+++ b/arch/mips/include/asm/mach-ip27/kernel-entry-init.h
@@ -49,7 +49,7 @@
 	dli	t0, 0xffffffffc0000000
 	dmtc0	t0, CP0_ENTRYHI
 	GET_NASID_SHFT	t3, t0
-	li	t0, 0x1c000		# Offset of text into node memory
+	li	t0, 0x40000		# Offset of text into node memory
 	dsllv	t1, t1, t3		# Shift text nasid into place
 	dsllv	t2, t2, t3		# Same for data nasid
 	or	t1, t1, t0		# Physical load address of kernel text
diff --git a/arch/mips/include/asm/sn/mapped_kernel.h b/arch/mips/include/asm/sn/mapped_kernel.h
index 3f1049807018..28227718e391 100644
--- a/arch/mips/include/asm/sn/mapped_kernel.h
+++ b/arch/mips/include/asm/sn/mapped_kernel.h
@@ -10,7 +10,7 @@
 
 /*
  * Note on how mapped kernels work: the text and data section is
- * compiled at cksseg segment (LOADADDR = 0xc001c000), and the
+ * compiled at cksseg segment (LOADADDR = 0xc0040000), and the
  * init/setup/data section gets a 16M virtual address bump in the
  * ld.script file (so that tlblo0 and tlblo1 maps the sections).
  * The vmlinux.64 section addresses are put in the xkseg range
@@ -18,8 +18,8 @@
  * on IRIX to see where the sections go. The Origin loader loads
  * the two sections contiguously in physical memory. The loader
  * sets the entry point into kernel_entry using a xkphys address,
- * but instead of using 0xa800000001160000, it uses the address
- * 0xa800000000160000, which is where it physically loaded that
+ * but instead of using 0xa800000001184000, it uses the address
+ * 0xa800000000184000, which is where it physically loaded that
  * code. So no jumps can be done before we have switched to using
  * cksseg addresses.
  */
diff --git a/arch/mips/sgi-ip27/Platform b/arch/mips/sgi-ip27/Platform
index e734ee6abd44..b312bf69bce1 100644
--- a/arch/mips/sgi-ip27/Platform
+++ b/arch/mips/sgi-ip27/Platform
@@ -1,16 +1,17 @@
 #
 # SGI-IP27 (Origin200/2000)
 #
-# Set the load address to >= 0xc000000000300000 if you want to leave space for
-# symmon, 0xc00000000001c000 for production kernels.  Note that the value must
-# be 16kb aligned or the handling of the current variable will break.
+# A Bedrock machine's PROM owns node memory below offset 0x40000, so that is
+# where the kernel loads.  Set the load address to >= 0xc000000000300000
+# instead if you want to leave space for symmon.  Note that the value must be
+# 16kb aligned or the handling of the current variable will break.
 #
 cflags-$(CONFIG_SGI_IP27)	+= -I$(srctree)/arch/mips/include/asm/mach-ip27
 ifdef CONFIG_MAPPED_KERNEL
-load-$(CONFIG_SGI_IP27)		+= 0xc00000004001c000
+load-$(CONFIG_SGI_IP27)		+= 0xc000000040040000
 OBJCOPYFLAGS			:= --change-addresses=0x3fffffff80000000
 dataoffset-$(CONFIG_SGI_IP27)	+= 0x01000000
 else
-load-$(CONFIG_SGI_IP27)		+= 0xa80000000001c000
+load-$(CONFIG_SGI_IP27)		+= 0xa800000000040000
 OBJCOPYFLAGS			:= --change-addresses=0x57ffffff80000000
 endif
-- 
2.47.3