From: Dave Stevenson <dave.stevenson@raspberrypi.com>
To: Sakari Ailus <sakari.ailus@linux.intel.com>,
Jai Luthra <jai.luthra@ideasonboard.com>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
Alexander Shiyan <eagle.alexander923@gmail.com>,
linux-media@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org,
Dave Stevenson <dave.stevenson@raspberrypi.com>
Subject: [PATCH v4 02/16] media: sony-starvis2: Reorder link frequencies to remove lookup
Date: Thu, 15 Oct 2026 16:57:28 +0100 [thread overview]
Message-ID: <20261015-media-starvis2-v4-2-75fcdb4163f3@raspberrypi.com> (raw)
In-Reply-To: <20261015-media-starvis2-v4-0-75fcdb4163f3@raspberrypi.com>
link_freqs_reg_value is table that just reverses the order of the
link frequency enum.
Reverse the order of the link frequencies so that the table is
redundant, and remove it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
---
drivers/media/i2c/sony-starvis2.c | 31 ++++++++++---------------------
1 file changed, 10 insertions(+), 21 deletions(-)
diff --git a/drivers/media/i2c/sony-starvis2.c b/drivers/media/i2c/sony-starvis2.c
index b4733990d03a..3656658e18a4 100644
--- a/drivers/media/i2c/sony-starvis2.c
+++ b/drivers/media/i2c/sony-starvis2.c
@@ -186,25 +186,14 @@ enum starvis2_lanemode {
/* Link frequency setup (DDR: lane rate = 2 x link freq) */
enum {
- STARVIS2_LINK_FREQ_297MHZ,
- STARVIS2_LINK_FREQ_360MHZ,
- STARVIS2_LINK_FREQ_445MHZ,
- STARVIS2_LINK_FREQ_594MHZ,
- STARVIS2_LINK_FREQ_720MHZ,
- STARVIS2_LINK_FREQ_891MHZ,
- STARVIS2_LINK_FREQ_1039MHZ,
- STARVIS2_LINK_FREQ_1188MHZ,
-};
-
-static const u8 link_freqs_reg_value[] = {
- [STARVIS2_LINK_FREQ_297MHZ] = 0x07,
- [STARVIS2_LINK_FREQ_360MHZ] = 0x06,
- [STARVIS2_LINK_FREQ_445MHZ] = 0x05,
- [STARVIS2_LINK_FREQ_594MHZ] = 0x04,
- [STARVIS2_LINK_FREQ_720MHZ] = 0x03,
- [STARVIS2_LINK_FREQ_891MHZ] = 0x02,
- [STARVIS2_LINK_FREQ_1039MHZ] = 0x01,
- [STARVIS2_LINK_FREQ_1188MHZ] = 0x00,
+ STARVIS2_LINK_FREQ_1188MHZ = 0x00,
+ STARVIS2_LINK_FREQ_1039MHZ = 0x01,
+ STARVIS2_LINK_FREQ_891MHZ = 0x02,
+ STARVIS2_LINK_FREQ_720MHZ = 0x03,
+ STARVIS2_LINK_FREQ_594MHZ = 0x04,
+ STARVIS2_LINK_FREQ_445MHZ = 0x05,
+ STARVIS2_LINK_FREQ_360MHZ = 0x06,
+ STARVIS2_LINK_FREQ_297MHZ = 0x07,
};
static const u64 link_freqs[] = {
@@ -913,7 +902,7 @@ static int starvis2_write_common(struct starvis2 *starvis2)
cci_write(starvis2->cci, STARVIS2_REG_INCK_SEL, starvis2->inck_sel_val,
&ret);
cci_write(starvis2->cci, STARVIS2_REG_DATARATE_SEL,
- link_freqs_reg_value[__ffs(starvis2->link_freq_bitmap)],
+ __fls(starvis2->link_freq_bitmap),
&ret);
cci_write(starvis2->cci, STARVIS2_REG_LANEMODE, starvis2->lane_mode,
&ret);
@@ -1175,7 +1164,7 @@ static int starvis2_init_controls(struct starvis2 *starvis2)
{
struct v4l2_ctrl_handler *ctrl_hdlr;
const u32 hmax_4lane =
- min_hmax_4lane[__ffs(starvis2->link_freq_bitmap)];
+ min_hmax_4lane[__fls(starvis2->link_freq_bitmap)];
const u32 lane_scale =
starvis2->lane_mode == STARVIS2_LANEMODE_2L ? 2 : 1;
struct i2c_client *client = v4l2_get_subdevdata(&starvis2->sd);
--
2.34.1
next prev parent reply other threads:[~2026-10-15 15:57 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-15 15:57 [PATCH v4 00/16] Update imx678 to act as a common Sony Starvis 2 driver Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 01/16] media: imx678: Rework into generic Starvis 2 sensor driver Dave Stevenson
2026-10-15 15:57 ` Dave Stevenson [this message]
2026-10-15 15:57 ` [PATCH v4 03/16] media: sony-starvis2: Always program the sensor in window mode Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 04/16] media: sony-starvis2: Parameterise the configuration to allow for other models Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 05/16] media: sony-starvis2: Rework 2 lane support for higher link freqs Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 06/16] media: sony-starvis2: Allow runtime control of link frequency Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 07/16] media: sony-starvis2: Correct the exposure range Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 08/16] media: sony-starvis2: Put module into standby after identify Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 09/16] media: sony-starvis2: Use pm_runtime_autosuspend Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 10/16] media: dt-bindings: sony,imx678: Add other Starvis 2 family members Dave Stevenson
2026-10-15 20:17 ` Rob Herring
2026-10-15 15:57 ` [PATCH v4 11/16] media: sony-starvis2: Add support for IMX662 Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 12/16] media: sony-starvis2: Add support for IMX675 Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 13/16] media: sony-starvis2: Add support for IMX832 Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 14/16] media: sony-starvis2: Only update bits for window mode Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 15/16] media: sony-starvis2: Parameterise exposure min and step Dave Stevenson
2026-10-15 15:57 ` [PATCH v4 16/16] media: sony-starvis2: Add support for IMX585 Dave Stevenson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261015-media-starvis2-v4-2-75fcdb4163f3@raspberrypi.com \
--to=dave.stevenson@raspberrypi.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=eagle.alexander923@gmail.com \
--cc=jai.luthra@ideasonboard.com \
--cc=krzk+dt@kernel.org \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=robh@kernel.org \
--cc=sakari.ailus@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®