mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Michael Riesch <michael.riesch@collabora.com>
To: Jason Yang <jason98166@gmail.com>, Vinod Koul <vkoul@kernel.org>,
	Neil Armstrong <neil.armstrong@linaro.org>,
	Manivannan Sadhasivam <mani@kernel.org>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Heiko Stuebner <heiko@sntech.de>,
	Guochun Huang <hero.huang@rock-chips.com>,
	Philipp Zabel <p.zabel@pengutronix.de>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>,
	Bryan O'Donoghue <bryan.odonoghue@linaro.org>,
	linux-phy@lists.infradead.org, devicetree@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v6 5/9] phy: rockchip-samsung-dcphy: Move block-level setup to runtime resume
Date: Wed, 11 Nov 2026 14:14:47 +0100	[thread overview]
Message-ID: <6fbe6fed-3ed4-4f87-a92b-dbd01e1674d3@collabora.com> (raw)
In-Reply-To: <20261110-dcphy-rx-v1-v6-5-d681ba20b36a@gmail.com>

Hi Jason,

Thanks for the patch!

On 11/10/26 09:18, Jason Yang wrote:
> The APB reset and the BIAS references have to be treated as block-level
> [1]: both the transmitter and the receiver need them, and they only have
> to be programmed once. They are programmed from the transmitter's
> power-on path today.
> 
> A later change registers one struct phy for each of them, and a second
> consumer coming up would then reset the block underneath a PHY that is
> already running.
> 
> Program them from runtime resume instead, where whichever of the two
> comes up first brings the block up and a second one no longer resets it.
> 
> This puts the BIAS writes ahead of the per-PHY reset assert, where the
> TRM's worked example has them after [1]. That is safe: neither M_RESETN
> nor S_RESETN covers the BIAS registers, and the values written are those
> registers' reset defaults.
> 
> [1] RK3588 TRM: sections 22.4.1 (address map), 22.4.2 (reset values),
>     22.6.1.2 (reset) and 22.6.4.1 (D-PHY transmitter start-up)
> 
> Signed-off-by: Jason Yang <jason98166@gmail.com>

Reviewed-by: Michael Riesch <michael.riesch@collabora.com>

Best regards,
Michael

> ---
>  drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c | 11 ++++++-----
>  1 file changed, 6 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c b/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c
> index 7a009d87a665..d6acc3e2d448 100644
> --- a/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c
> +++ b/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c
> @@ -1346,7 +1346,6 @@ static int samsung_mipi_dphy_power_on(struct samsung_mipi_dcphy *samsung)
>  
>  	reset_control_assert(samsung->m_phy_rst);
>  
> -	samsung_mipi_dcphy_bias_block_enable(samsung);
>  	samsung_mipi_dcphy_pll_configure(samsung);
>  	samsung_mipi_dphy_clk_lane_timing_init(samsung);
>  	samsung_mipi_dphy_data_lane_timing_init(samsung);
> @@ -1373,10 +1372,6 @@ static int samsung_mipi_dcphy_power_on(struct phy *phy)
>  {
>  	struct samsung_mipi_dcphy *samsung = phy_get_drvdata(phy);
>  
> -	reset_control_assert(samsung->apb_rst);
> -	udelay(1);
> -	reset_control_deassert(samsung->apb_rst);
> -
>  	switch (samsung->type) {
>  	case PHY_TYPE_DPHY:
>  		return samsung_mipi_dphy_power_on(samsung);
> @@ -1667,6 +1662,12 @@ static __maybe_unused int samsung_mipi_dcphy_runtime_resume(struct device *dev)
>  		return ret;
>  	}
>  
> +	reset_control_assert(samsung->apb_rst);
> +	udelay(1);
> +	reset_control_deassert(samsung->apb_rst);
> +
> +	samsung_mipi_dcphy_bias_block_enable(samsung);
> +
>  	return 0;
>  }
>  
> 


  reply	other threads:[~2026-11-11 13:15 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-10  8:18 [PATCH v6 0/9] phy: rockchip-samsung-dcphy: Add the MIPI D-PHY receiver Jason Yang
2026-11-10  8:18 ` [PATCH v6 1/9] dt-bindings: phy: Add PHY_DIRECTION_TX/RX definitions Jason Yang
2026-11-11 10:29   ` Michael Riesch
2026-11-10  8:18 ` [PATCH v6 2/9] dt-bindings: phy: rockchip,rk3588-mipi-dcphy: Select TX or RX, add phy-type Jason Yang
2026-11-10 18:02   ` Rob Herring (Arm)
2026-11-11 10:33   ` Michael Riesch
2026-11-10  8:18 ` [PATCH v6 3/9] phy: rockchip-samsung-dcphy: Unwind power-on on PLL lock failure Jason Yang
2026-11-11 13:02   ` Michael Riesch
2026-11-10  8:18 ` [PATCH v6 4/9] phy: rockchip-samsung-dcphy: Always write the rate-dependent registers Jason Yang
2026-11-11 13:05   ` Michael Riesch
2026-11-10  8:18 ` [PATCH v6 5/9] phy: rockchip-samsung-dcphy: Move block-level setup to runtime resume Jason Yang
2026-11-11 13:14   ` Michael Riesch [this message]
2026-11-10  8:18 ` [PATCH v6 6/9] phy: rockchip-samsung-dcphy: Name the transmitter helpers and ops Jason Yang
2026-11-10  8:18 ` [PATCH v6 7/9] phy: rockchip-samsung-dcphy: Support the new phy-type and direction binding Jason Yang
2026-11-10  8:18 ` [PATCH v6 8/9] phy: rockchip-samsung-dcphy: Add MIPI D-PHY receiver support Jason Yang
2026-11-10  8:18 ` [PATCH v6 9/9] arm64: dts: rockchip: add the dcphy mipi csi-2 receiver nodes to rk3588 Jason Yang
2026-11-11 12:32   ` Michael Riesch

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=6fbe6fed-3ed4-4f87-a92b-dbd01e1674d3@collabora.com \
    --to=michael.riesch@collabora.com \
    --cc=bryan.odonoghue@linaro.org \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=heiko@sntech.de \
    --cc=hero.huang@rock-chips.com \
    --cc=jason98166@gmail.com \
    --cc=krzk+dt@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-phy@lists.infradead.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=mani@kernel.org \
    --cc=neil.armstrong@linaro.org \
    --cc=p.zabel@pengutronix.de \
    --cc=robh@kernel.org \
    --cc=sebastian.reichel@collabora.com \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®