mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
* Andre IDE patches + Promise, UDMA detection
@ 2002-01-17  0:14 Arkadiusz Miskiewicz
  2002-01-17  0:26 ` Andre Hedrick
  0 siblings, 1 reply; 3+ messages in thread
From: Arkadiusz Miskiewicz @ 2002-01-17  0:14 UTC (permalink / raw)
  To: linux-kernel


Hi,

I'm using 2.4.17 with ide.2.4.16.12102001.patch.bz2 + other
patches (listed here: http://cvs.pld.org.pl/SPECS/kernel.spec?rev=1.70.2.390)
on FIC LX based (quite old) mainboard + external PCI controller:

00:07.1 IDE interface: Intel Corp. 82371AB PIIX4 IDE (rev 01)
00:08.0 Unknown mass storage controller: Promise Technology, Inc. 20268 (rev 01)

My IDE setup is fully modular (well, whole kernel is):
xfs                   479200   4  (autoclean)
xfs_support             6216   0  (autoclean) [xfs]
pagebuf                22112   4  (autoclean) [xfs xfs_support]
nls_iso8859-1           2880   1  (autoclean)
nls_cp437               4384   1  (autoclean)
vfat                    9788   1  (autoclean)
fat                    30680   0  (autoclean) [vfat]
sr_mod                 13656   0  (autoclean) (unused)
scsi_mod               86776   1  (autoclean) [sr_mod]
ide-cd                 27552   0 
cdrom                  28320   0  [sr_mod ide-cd]
ext3                   58772   1  (autoclean)
ide-disk                9712   8  (autoclean)
ide-mod               153756   8  (autoclean) [ide-cd ide-disk]
jbd                    34424   1  (autoclean) [ext3]

Kernel boots fine:
Linux version 2.4.17 (builder@kenny) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Tue Jan 15 13:19:47 UTC 2002
...
Freeing initrd memory: 174k freed
VFS: Mounted root (romfs filesystem) readonly.
Journalled Block Device driver loaded
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
PDC20268: IDE controller on PCI bus 00 dev 40
PCI: Found IRQ 11 for device 00:08.0
PDC20268: chipset revision 1
PDC20268: not 100% native mode: will probe irqs later
PDC20268: ROM enabled at 0xea000000
    ide2: BM-DMA at 0xe400-0xe407, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xe408-0xe40f, BIOS settings: hdg:pio, hdh:pio
hda: ASUS CD-S500/A, ATAPI CD/DVD-ROM drive
hde: IBM-DTLA-307030, ATA DISK drive
hdf: IBM-DTLA-305040, ATA DISK drive
hdh: ST360021A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0xd400-0xd407,0xd802 on irq 11
ide3 at 0xdc00-0xdc07,0xe002 on irq 11
hde: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(33)
hdf: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=79780/16/63, UDMA(33)
hdh: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63, UDMA(33)
Partition check:
 /dev/ide/host2/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 >
 /dev/ide/host2/bus0/target1/lun0: p1 p2
 /dev/ide/host2/bus1/target1/lun0: p1
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.

Unfortunately it thinks that all my harddrives (connected to promise
via 80wire cable) are UDMA33! Now _sometimes_ after boot it detects
these (properly) as UDMA100 and sometimes (seems more frequently)
as UDMA33.

Now when ide module detect my disk as UDMA33 and I have in my
initscripts hdparm (4.6) -X69 -c1 -d1 -m16 then some my processes
hang in D-state accessing hardrive (hdh for example).
Removing -X69 fixes that even if my kernel thinks that my drivers
are UDMA33 only... 

So now it will be great to get ide module properly detecting UDMA.
-- 
Arkadiusz Miśkiewicz   IPv6 ready PLD Linux at http://www.pld.org.pl
misiek(at)pld.org.pl   AM2-6BONE, 1024/3DB19BBD, arekm(at)ircnet, PWr


^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: Andre IDE patches + Promise, UDMA detection
  2002-01-17  0:14 Andre IDE patches + Promise, UDMA detection Arkadiusz Miskiewicz
@ 2002-01-17  0:26 ` Andre Hedrick
  2002-01-17  8:31   ` Arkadiusz Miskiewicz
  0 siblings, 1 reply; 3+ messages in thread
From: Andre Hedrick @ 2002-01-17  0:26 UTC (permalink / raw)
  To: Arkadiusz Miskiewicz; +Cc: linux-kernel


Because sometimes the decay rate of the capacitance check after execute
drive diagnostics command from POST is faster than boot.

Also if this problem happens only after a cold boot, but a warm boot is
valid, you can set the CONFIG_IDEDMA_IVB=y

Regards,

On 17 Jan 2002, Arkadiusz Miskiewicz wrote:

> 
> Hi,
> 
> I'm using 2.4.17 with ide.2.4.16.12102001.patch.bz2 + other
> patches (listed here: http://cvs.pld.org.pl/SPECS/kernel.spec?rev=1.70.2.390)
> on FIC LX based (quite old) mainboard + external PCI controller:
> 
> 00:07.1 IDE interface: Intel Corp. 82371AB PIIX4 IDE (rev 01)
> 00:08.0 Unknown mass storage controller: Promise Technology, Inc. 20268 (rev 01)
> 
> My IDE setup is fully modular (well, whole kernel is):
> xfs                   479200   4  (autoclean)
> xfs_support             6216   0  (autoclean) [xfs]
> pagebuf                22112   4  (autoclean) [xfs xfs_support]
> nls_iso8859-1           2880   1  (autoclean)
> nls_cp437               4384   1  (autoclean)
> vfat                    9788   1  (autoclean)
> fat                    30680   0  (autoclean) [vfat]
> sr_mod                 13656   0  (autoclean) (unused)
> scsi_mod               86776   1  (autoclean) [sr_mod]
> ide-cd                 27552   0 
> cdrom                  28320   0  [sr_mod ide-cd]
> ext3                   58772   1  (autoclean)
> ide-disk                9712   8  (autoclean)
> ide-mod               153756   8  (autoclean) [ide-cd ide-disk]
> jbd                    34424   1  (autoclean) [ext3]
> 
> Kernel boots fine:
> Linux version 2.4.17 (builder@kenny) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Tue Jan 15 13:19:47 UTC 2002
> ...
> Freeing initrd memory: 174k freed
> VFS: Mounted root (romfs filesystem) readonly.
> Journalled Block Device driver loaded
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> PIIX4: IDE controller on PCI bus 00 dev 39
> PIIX4: chipset revision 1
> PIIX4: not 100% native mode: will probe irqs later
>     ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
>     ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
> PDC20268: IDE controller on PCI bus 00 dev 40
> PCI: Found IRQ 11 for device 00:08.0
> PDC20268: chipset revision 1
> PDC20268: not 100% native mode: will probe irqs later
> PDC20268: ROM enabled at 0xea000000
>     ide2: BM-DMA at 0xe400-0xe407, BIOS settings: hde:pio, hdf:pio
>     ide3: BM-DMA at 0xe408-0xe40f, BIOS settings: hdg:pio, hdh:pio
> hda: ASUS CD-S500/A, ATAPI CD/DVD-ROM drive
> hde: IBM-DTLA-307030, ATA DISK drive
> hdf: IBM-DTLA-305040, ATA DISK drive
> hdh: ST360021A, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide2 at 0xd400-0xd407,0xd802 on irq 11
> ide3 at 0xdc00-0xdc07,0xe002 on irq 11
> hde: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(33)
> hdf: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=79780/16/63, UDMA(33)
> hdh: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63, UDMA(33)
> Partition check:
>  /dev/ide/host2/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 >
>  /dev/ide/host2/bus0/target1/lun0: p1 p2
>  /dev/ide/host2/bus1/target1/lun0: p1
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> 
> Unfortunately it thinks that all my harddrives (connected to promise
> via 80wire cable) are UDMA33! Now _sometimes_ after boot it detects
> these (properly) as UDMA100 and sometimes (seems more frequently)
> as UDMA33.
> 
> Now when ide module detect my disk as UDMA33 and I have in my
> initscripts hdparm (4.6) -X69 -c1 -d1 -m16 then some my processes
> hang in D-state accessing hardrive (hdh for example).
> Removing -X69 fixes that even if my kernel thinks that my drivers
> are UDMA33 only... 
> 
> So now it will be great to get ide module properly detecting UDMA.
> -- 
> Arkadiusz Mi¶kiewicz   IPv6 ready PLD Linux at http://www.pld.org.pl
> misiek(at)pld.org.pl   AM2-6BONE, 1024/3DB19BBD, arekm(at)ircnet, PWr
> 
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
> 

Andre Hedrick
Linux Disk Certification Project                Linux ATA Development


^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: Andre IDE patches + Promise, UDMA detection
  2002-01-17  0:26 ` Andre Hedrick
@ 2002-01-17  8:31   ` Arkadiusz Miskiewicz
  0 siblings, 0 replies; 3+ messages in thread
From: Arkadiusz Miskiewicz @ 2002-01-17  8:31 UTC (permalink / raw)
  To: Andre Hedrick; +Cc: linux-kernel

Andre Hedrick <andre@linuxdiskcert.org> writes:

> Because sometimes the decay rate of the capacitance check after execute
> drive diagnostics command from POST is faster than boot.
> 
> Also if this problem happens only after a cold boot, but a warm boot is
> valid, you can set the CONFIG_IDEDMA_IVB=y
Unfortunately problem always happens - cold boot, warm boot - no difference.
So setting CONFIG_IDEDMA_IVB=y won't help in this case?

My IDE config looks that:
CONFIG_IDE=m
CONFIG_BLK_DEV_IDE=m
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=m
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_IDEDISK_STROKE is not set
CONFIG_IDE_TASKFILE_IO=y
# CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
# CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set
# CONFIG_BLK_DEV_IDEDISK_IBM is not set
# CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set
# CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set
# CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set
# CONFIG_BLK_DEV_IDEDISK_WD is not set
CONFIG_BLK_DEV_IDECS=m
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDEFLOPPY=m
CONFIG_BLK_DEV_IDESCSI=m
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
# CONFIG_IDEDMA_PCI_AUTO is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set
# CONFIG_IDE_CHIPSETS is not set
# CONFIG_IDEDMA_AUTO is not set
# CONFIG_IDEDMA_IVB is not set
CONFIG_BLK_DEV_IDE_MODES=y
CONFIG_CD_NO_IDESCSI=y

> > Unfortunately it thinks that all my harddrives (connected to promise
> > via 80wire cable) are UDMA33! Now _sometimes_ after boot it detects
> > these (properly) as UDMA100 and sometimes (seems more frequently)
> > as UDMA33.

> Andre Hedrick
> Linux Disk Certification Project                Linux ATA Development

-- 
Arkadiusz Miśkiewicz   IPv6 ready PLD Linux at http://www.pld.org.pl
misiek(at)pld.org.pl   AM2-6BONE, 1024/3DB19BBD, arekm(at)ircnet, PWr

^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2002-01-17  8:32 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-01-17  0:14 Andre IDE patches + Promise, UDMA detection Arkadiusz Miskiewicz
2002-01-17  0:26 ` Andre Hedrick
2002-01-17  8:31   ` Arkadiusz Miskiewicz

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®