* [PATCH 0/3] Enable RZ/G3L SDHI
@ 2026-11-12 18:48 Biju Das
2026-11-12 18:48 ` [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK Biju Das
` (3 more replies)
0 siblings, 4 replies; 13+ messages in thread
From: Biju Das @ 2026-11-12 18:48 UTC (permalink / raw)
To: Geert Uytterhoeven, Magnus Damm, Wolfram Sang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-renesas-soc, devicetree, linux-kernel, Biju Das
This patch series enable eMMC on SDHI0 and SDHI1 on SDHI2
This patch series is depend upon [1]
[1] https://lore.kernel.org/all/20261104-usb_rzg3l-v8-0-ab109c4bd108@bp.renesas.com/
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
---
Biju Das (3):
arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK
arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0
arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2
arch/arm64/boot/dts/renesas/r9a08g046.dtsi | 73 ++++++-
arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts | 89 ++++++++
arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi | 231 +++++++++++++++++++++
3 files changed, 392 insertions(+), 1 deletion(-)
---
base-commit: e7d07f2ed4b4a14f79bc9fb417d25695cb7679a9
change-id: 20261112-sdhi_rzg3l-e0c7dbf7cfdd
Best regards,
--
Biju Das <biju.das.jz@bp.renesas.com>
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK
2026-11-12 18:48 [PATCH 0/3] Enable RZ/G3L SDHI Biju Das
@ 2026-11-12 18:48 ` Biju Das
2026-11-20 12:52 ` Geert Uytterhoeven
2026-11-12 18:48 ` [PATCH 2/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0 Biju Das
` (2 subsequent siblings)
3 siblings, 1 reply; 13+ messages in thread
From: Biju Das @ 2026-11-12 18:48 UTC (permalink / raw)
To: Geert Uytterhoeven, Magnus Damm, Wolfram Sang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-renesas-soc, devicetree, linux-kernel, Biju Das
From: Biju Das <biju.das.jz@bp.renesas.com>
Add device tree nodes for the three SDHI controllers (SDHI{0,1,2})
on the RZ/G3L SoC (r9a08g046) and enable SDHI1 on the RZ/G3L SMARC
EVK platform with pincontrol and GPIO-based voltage switching
regulator support.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
---
arch/arm64/boot/dts/renesas/r9a08g046.dtsi | 73 +++++++++++++++++-
arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts | 88 ++++++++++++++++++++++
2 files changed, 160 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/renesas/r9a08g046.dtsi b/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
index 7e379f6ab837..29ce1ab2a57f 100644
--- a/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
+++ b/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
@@ -1062,9 +1062,80 @@ dmac: dma-controller@11820000 {
dma-channels = <16>;
};
+ sdhi0: mmc@11c00000 {
+ compatible = "renesas,sdhi-r9a08g046";
+ reg = <0x0 0x11c00000 0 0x10000>;
+ interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD R9A08G046_SDHI0_IMCLK>,
+ <&cpg CPG_MOD R9A08G046_SDHI0_CLK_HS>,
+ <&cpg CPG_MOD R9A08G046_SDHI0_IMCLK2>,
+ <&cpg CPG_MOD R9A08G046_SDHI0_IACLKM>,
+ <&cpg CPG_MOD R9A08G046_SDHI0_IACLKS>;
+ clock-names = "core", "clkh", "cd", "aclkm", "aclks";
+ max-frequency = <150000000>;
+ resets = <&cpg R9A08G046_SDHI0_IXRST>,
+ <&cpg R9A08G046_SDHI0_IXRSTAXIM>,
+ <&cpg R9A08G046_SDHI0_IXRSTAXIS>;
+ reset-names = "rst", "axim", "axis";
+ power-domains = <&cpg>;
+ status = "disabled";
+ };
+
sdhi1: mmc@11c10000 {
+ compatible = "renesas,sdhi-r9a08g046";
reg = <0x0 0x11c10000 0 0x10000>;
- /* placeholder */
+ interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD R9A08G046_SDHI1_IMCLK>,
+ <&cpg CPG_MOD R9A08G046_SDHI1_CLK_HS>,
+ <&cpg CPG_MOD R9A08G046_SDHI1_IMCLK2>,
+ <&cpg CPG_MOD R9A08G046_SDHI1_IACLKM>,
+ <&cpg CPG_MOD R9A08G046_SDHI1_IACLKS>;
+ clock-names = "core", "clkh", "cd", "aclkm", "aclks";
+ max-frequency = <150000000>;
+ resets = <&cpg R9A08G046_SDHI1_IXRST>,
+ <&cpg R9A08G046_SDHI1_IXRSTAXIM>,
+ <&cpg R9A08G046_SDHI1_IXRSTAXIS>;
+ reset-names = "rst", "axim", "axis";
+ power-domains = <&cpg>;
+ status = "disabled";
+
+ sdhi1_vqmmc: vqmmc-regulator {
+ regulator-name = "SDHI1-VQMMC";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <1200>;
+ status = "disabled";
+ };
+ };
+
+ sdhi2: mmc@11c20000 {
+ compatible = "renesas,sdhi-r9a08g046";
+ reg = <0x0 0x11c20000 0 0x10000>;
+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD R9A08G046_SDHI2_IMCLK>,
+ <&cpg CPG_MOD R9A08G046_SDHI2_CLK_HS>,
+ <&cpg CPG_MOD R9A08G046_SDHI2_IMCLK2>,
+ <&cpg CPG_MOD R9A08G046_SDHI2_IACLKM>,
+ <&cpg CPG_MOD R9A08G046_SDHI2_IACLKS>;
+ clock-names = "core", "clkh", "cd", "aclkm", "aclks";
+ max-frequency = <150000000>;
+ resets = <&cpg R9A08G046_SDHI2_IXRST>,
+ <&cpg R9A08G046_SDHI2_IXRSTAXIM>,
+ <&cpg R9A08G046_SDHI2_IXRSTAXIS>;
+ reset-names = "rst", "axim", "axis";
+ power-domains = <&cpg>;
+ status = "disabled";
+
+ sdhi2_vqmmc: vqmmc-regulator {
+ regulator-name = "SDHI2-VQMMC";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <1200>;
+ status = "disabled";
+ };
};
eth0: ethernet@11c30000 {
diff --git a/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts b/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
index 9ffaead2c6be..2f3266129733 100644
--- a/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
+++ b/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
@@ -14,6 +14,7 @@
#define SW_GPIO4 1
#define SW_I3C_EN 0
#define SW_SER0_PMOD 1
+#define SW_SDIO_M2E 0
#define PMOD_GPIO4 0
#define PMOD_GPIO6 0
@@ -38,6 +39,7 @@ / {
aliases {
i2c2 = &i2c2;
i2c3 = &i2c3;
+ mmc1 = &sdhi1;
serial0 = &rsci2;
serial1 = &rsci3;
serial2 = &rsci1;
@@ -69,6 +71,19 @@ codec_dai: codec {
};
};
#endif
+
+#if RZ_BOOT_MODE3
+ vqmmc_sd1_pvdd: regulator-vqmmc-sd1-pvdd {
+ compatible = "regulator-gpio";
+ regulator-name = "SD1_PVDD";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&pinctrl RZG3L_GPIO(J, 1) GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <3300000 0>, <1800000 1>;
+ regulator-ramp-delay = <1200>;
+ };
+#endif
};
&i2c2 {
@@ -195,6 +210,68 @@ scif0_pins: scif0 {
power-source = <1800>;
};
+#if RZ_BOOT_MODE3
+ sd1-pwr-en-hog {
+ gpio-hog;
+ gpios = <RZG3L_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "sd1_pwr_en";
+ };
+#endif
+
+ sdhi1_pins: sd1 {
+ sd1-cd {
+ pinmux = <RZG3L_PORT_PINMUX(J, 0, 8)>; /* SD1_CD */
+ };
+
+ sd1-clk {
+ pinmux = <RZG3L_PORT_PINMUX(G, 0, 1)>; /* SD1_CLK */
+ power-source = <3300>;
+ };
+
+ sd1-cmd {
+ pinmux = <RZG3L_PORT_PINMUX(G, 1, 1)>; /* SD1_CMD */
+ input-enable;
+ power-source = <3300>;
+ bias-pull-up;
+ };
+
+ sd1-data {
+ pinmux = <RZG3L_PORT_PINMUX(G, 2, 1)>, /* SD1_DAT0 */
+ <RZG3L_PORT_PINMUX(G, 3, 1)>, /* SD1_DAT1 */
+ <RZG3L_PORT_PINMUX(G, 4, 1)>, /* SD1_DAT2 */
+ <RZG3L_PORT_PINMUX(G, 5, 1)>; /* SD1_DAT3 */
+ input-enable;
+ power-source = <3300>;
+ };
+ };
+
+ sdhi1_uhs_pins: sd1-uhs {
+ sd1-cd {
+ pinmux = <RZG3L_PORT_PINMUX(J, 0, 8)>; /* SD1_CD */
+ };
+
+ sd1-clk {
+ pinmux = <RZG3L_PORT_PINMUX(G, 0, 1)>; /* SD1_CLK */
+ power-source = <1800>;
+ };
+
+ sd1-cmd {
+ pinmux = <RZG3L_PORT_PINMUX(G, 1, 1)>; /* SD1_CMD */
+ input-enable;
+ power-source = <1800>;
+ };
+
+ sd1-data {
+ pinmux = <RZG3L_PORT_PINMUX(G, 2, 1)>, /* SD1_DAT0 */
+ <RZG3L_PORT_PINMUX(G, 3, 1)>, /* SD1_DAT1 */
+ <RZG3L_PORT_PINMUX(G, 4, 1)>, /* SD1_DAT2 */
+ <RZG3L_PORT_PINMUX(G, 5, 1)>; /* SD1_DAT3 */
+ input-enable;
+ power-source = <1800>;
+ };
+ };
+
ssi0_pins: ssi0 {
pinmux = <RZG3L_PORT_PINMUX(H, 0, 9)>, /* SSIF0_RXD */
<RZG3L_PORT_PINMUX(H, 1, 9)>, /* SSIF0_BCK */
@@ -255,6 +332,17 @@ &scif0 {
pinctrl-names = "default";
};
+#if RZ_BOOT_MODE3
+&sdhi1 {
+ pinctrl-0 = <&sdhi1_pins>;
+ pinctrl-1 = <&sdhi1_uhs_pins>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <&vqmmc_sd1_pvdd>;
+};
+#endif
+
#if !SW_SD2_EN
&ssi0 {
clocks = <&cpg CPG_MOD R9A08G046_SSI0_PCLK2>,
--
2.43.0
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 2/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0
2026-11-12 18:48 [PATCH 0/3] Enable RZ/G3L SDHI Biju Das
2026-11-12 18:48 ` [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK Biju Das
@ 2026-11-12 18:48 ` Biju Das
2026-11-20 13:04 ` Geert Uytterhoeven
2026-11-12 18:48 ` [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2 Biju Das
2026-11-16 10:05 ` [PATCH 0/3] Enable RZ/G3L SDHI Wolfram Sang
3 siblings, 1 reply; 13+ messages in thread
From: Biju Das @ 2026-11-12 18:48 UTC (permalink / raw)
To: Geert Uytterhoeven, Magnus Damm, Wolfram Sang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-renesas-soc, devicetree, linux-kernel, Biju Das
From: Biju Das <biju.das.jz@bp.renesas.com>
Add support for enabling SD card or eMMC on SDHI0 on the RZ/G3L SMARC
SoM. The selection between SD and eMMC is controlled by the
SW_SD0_DEV_SEL macro in the board DTS, which must match the position
of switch SYS.1 on the SoM. By default, eMMC is enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
---
arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts | 1 +
arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi | 143 +++++++++++++++++++++
2 files changed, 144 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts b/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
index 2f3266129733..5f5441c47335 100644
--- a/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
+++ b/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
@@ -9,6 +9,7 @@
/* Switch selection settings */
#define RZ_BOOT_MODE3 1
+#define SW_SD0_DEV_SEL 0
#define SW_SD2_EN 0
#define SW_DPI_EN 0
#define SW_GPIO4 1
diff --git a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
index 91b2d0d43104..e84840fa5086 100644
--- a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
@@ -9,6 +9,10 @@
* Please set the below switch position on the SoM and the corresponding macro
* on the board DTS:
*
+ * Switch position SYS.1, Macro SW_SD0_DEV_SEL:
+ * 0 - SD0 is connected to eMMC (default)
+ * 1 - SD0 is connected to uSD0 card
+ *
* Switch position SYS.2, Macro SW_I3C_EN:
* 0 - SMARC_I2C_GP is enabled
* 1 - I3C is enabled
@@ -37,6 +41,7 @@ aliases {
ethernet0 = ð0;
ethernet1 = ð1;
i2c0 = &i2c0;
+ mmc0 = &sdhi0;
};
memory@48000000 {
@@ -78,6 +83,19 @@ reg_3p3v: regulator-3p3v {
regulator-always-on;
};
+#if SW_SD0_DEV_SEL
+ vqmmc_sd0_pvdd: vqmmc-sd0-pvdd {
+ compatible = "regulator-gpio";
+ regulator-name = "SD0_PVDD";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&pinctrl RZG3L_GPIO(L, 4) GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <3300000 0>, <1800000 1>;
+ regulator-ramp-delay = <1200>;
+ };
+#endif
+
x2_clk: x2-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -241,7 +259,132 @@ i2c0_pins: i2c0 {
pinmux = <RZG3L_PORT_PINMUX(L, 2, 4)>, /* RIIC0_SCL */
<RZG3L_PORT_PINMUX(L, 3, 4)>; /* RIIC0_SDA */
};
+
+ sd0-pwr-en-hog {
+ gpio-hog;
+ gpios = <RZG3L_GPIO(5, 1) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "sd0_pwr_en";
+ };
+
+ sdhi0_emmc_pins: sd0-emmc {
+ sd0-clk {
+ pins = "SD0_CLK";
+ power-source = <1800>;
+ drive-strength-microamp = <9000>;
+ };
+
+ sd0-cmd {
+ pins = "SD0_CMD";
+ input-enable;
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+
+ sd0-data {
+ pins = "SD0_DAT0", "SD0_DAT1", "SD0_DAT2", "SD0_DAT3",
+ "SD0_DAT4", "SD0_DAT5", "SD0_DAT6", "SD0_DAT7";
+ input-enable;
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+
+ sd0-rst {
+ pins = "SD0_RST#";
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+
+ sd0-ds {
+ pins = "SD0_DS";
+ input-enable;
+ bias-pull-down;
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+ };
+
+ sdhi0_usd_pins: sd0-usd {
+ sd0-cd {
+ pinmux = <RZG2L_PORT_PINMUX(5, 0, 8)>; /* SD0_CD */
+ };
+
+ sd0-clk {
+ pins = "SD0_CLK";
+ drive-strength-microamp = <8000>;
+ power-source = <3300>;
+ };
+
+ sd0-cmd {
+ pins = "SD0_CMD";
+ input-enable;
+ drive-strength-microamp = <8000>;
+ power-source = <3300>;
+ };
+
+ sd0-data {
+ pins = "SD0_DAT0", "SD0_DAT1", "SD0_DAT2", "SD0_DAT3";
+ input-enable;
+ drive-strength-microamp = <8000>;
+ power-source = <3300>;
+ };
+ };
+
+ sdhi0_usd_uhs_pins: sd0-usd-uhs {
+ sd0-cd {
+ pinmux = <RZG2L_PORT_PINMUX(5, 0, 8)>; /* SD0_CD */
+ };
+
+ sd0-clk {
+ pins = "SD0_CLK";
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+
+ sd0-cmd {
+ pins = "SD0_CMD";
+ input-enable;
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+
+ sd0-data {
+ pins = "SD0_DAT0", "SD0_DAT1", "SD0_DAT2", "SD0_DAT3";
+ input-enable;
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+ };
+};
+
+#if (SW_SD0_DEV_SEL)
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_usd_pins>;
+ pinctrl-1 = <&sdhi0_usd_uhs_pins>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <&vqmmc_sd0_pvdd>;
+ bus-width = <4>;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+#else
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_emmc_pins>;
+ pinctrl-1 = <&sdhi0_emmc_pins>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ fixed-emmc-driver-type = <1>;
+ status = "okay";
};
+#endif
&wdt0 {
timeout-sec = <60>;
--
2.43.0
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2
2026-11-12 18:48 [PATCH 0/3] Enable RZ/G3L SDHI Biju Das
2026-11-12 18:48 ` [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK Biju Das
2026-11-12 18:48 ` [PATCH 2/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0 Biju Das
@ 2026-11-12 18:48 ` Biju Das
2026-11-20 13:17 ` Geert Uytterhoeven
2026-11-16 10:05 ` [PATCH 0/3] Enable RZ/G3L SDHI Wolfram Sang
3 siblings, 1 reply; 13+ messages in thread
From: Biju Das @ 2026-11-12 18:48 UTC (permalink / raw)
To: Geert Uytterhoeven, Magnus Damm, Wolfram Sang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-renesas-soc, devicetree, linux-kernel, Biju Das
From: Biju Das <biju.das.jz@bp.renesas.com>
Enable SDHI2 on the RZ/G3L SMARC EVK platform using the internal
voltage regulator for voltage switching. SDHI2 signals are muxed
with I2S0; the selection is controlled by the SW_SD2_EN macro in
the board DTS, which must match the position of switch SYS.4 on
the SoM. By default, I2S0 is enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
---
arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi | 88 ++++++++++++++++++++++++
1 file changed, 88 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
index e84840fa5086..a5aec82c0250 100644
--- a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
@@ -42,6 +42,7 @@ aliases {
ethernet1 = ð1;
i2c0 = &i2c0;
mmc0 = &sdhi0;
+ mmc2 = &sdhi2;
};
memory@48000000 {
@@ -355,6 +356,74 @@ sd0-data {
power-source = <1800>;
};
};
+
+ sdhi2_pins: sd2 {
+ sd2-cd {
+ pinmux = <RZG3L_PORT_PINMUX(K, 0, 1)>; /* SD2_CD */
+ };
+
+ sd2-clk {
+ pinmux = <RZG3L_PORT_PINMUX(H, 0, 1)>; /* SD2_CLK */
+ power-source = <3300>;
+ };
+
+ sd2-cmd {
+ pinmux = <RZG3L_PORT_PINMUX(H, 1, 1)>; /* SD2_CMD */
+ input-enable;
+ power-source = <3300>;
+ };
+
+ sd2-data {
+ pinmux = <RZG3L_PORT_PINMUX(H, 2, 1)>, /* SD2_DAT0 */
+ <RZG3L_PORT_PINMUX(H, 3, 1)>, /* SD2_DAT1 */
+ <RZG3L_PORT_PINMUX(H, 4, 1)>, /* SD2_DAT2 */
+ <RZG3L_PORT_PINMUX(H, 5, 1)>; /* SD2_DAT3 */
+ input-enable;
+ power-source = <3300>;
+ };
+
+ sd2-iovs {
+ pinmux = <RZG3L_PORT_PINMUX(K, 1, 1)>; /* SD2_IOVS */
+ };
+
+ sd2-pwen {
+ pinmux = <RZG3L_PORT_PINMUX(K, 2, 1)>; /* SD2_PWEN */
+ };
+ };
+
+ sdhi2_pins_uhs: sd2-uhs {
+ sd2-cd {
+ pinmux = <RZG3L_PORT_PINMUX(K, 0, 1)>; /* SD2_CD */
+ };
+
+ sd2-clk {
+ pinmux = <RZG3L_PORT_PINMUX(H, 0, 1)>; /* SD2_CLK */
+ power-source = <1800>;
+ };
+
+ sd2-cmd {
+ pinmux = <RZG3L_PORT_PINMUX(H, 1, 1)>; /* SD2_CMD */
+ input-enable;
+ power-source = <1800>;
+ };
+
+ sd2-data {
+ pinmux = <RZG3L_PORT_PINMUX(H, 2, 1)>, /* SD2_DAT0 */
+ <RZG3L_PORT_PINMUX(H, 3, 1)>, /* SD2_DAT1 */
+ <RZG3L_PORT_PINMUX(H, 4, 1)>, /* SD2_DAT2 */
+ <RZG3L_PORT_PINMUX(H, 5, 1)>; /* SD2_DAT3 */
+ input-enable;
+ power-source = <1800>;
+ };
+
+ sd2-iovs {
+ pinmux = <RZG3L_PORT_PINMUX(K, 1, 1)>; /* SD2_IOVS */
+ };
+
+ sd2-pwen {
+ pinmux = <RZG3L_PORT_PINMUX(K, 2, 1)>; /* SD2_PWEN */
+ };
+ };
};
#if (SW_SD0_DEV_SEL)
@@ -386,6 +455,25 @@ &sdhi0 {
};
#endif
+#if SW_SD2_EN
+&sdhi2 {
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <&sdhi2_vqmmc>;
+ bus-width = <4>;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&sdhi2_vqmmc {
+ status = "okay";
+};
+#endif
+
&wdt0 {
timeout-sec = <60>;
status = "okay";
--
2.43.0
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 0/3] Enable RZ/G3L SDHI
2026-11-12 18:48 [PATCH 0/3] Enable RZ/G3L SDHI Biju Das
` (2 preceding siblings ...)
2026-11-12 18:48 ` [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2 Biju Das
@ 2026-11-16 10:05 ` Wolfram Sang
2026-11-16 10:09 ` Biju Das
3 siblings, 1 reply; 13+ messages in thread
From: Wolfram Sang @ 2026-11-16 10:05 UTC (permalink / raw)
To: Biju Das
Cc: Geert Uytterhoeven, Magnus Damm, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, linux-renesas-soc, devicetree,
linux-kernel, Biju Das
[-- Attachment #1: Type: text/plain, Size: 430 bytes --]
Hi Biju,
On Thu, Nov 12, 2026 at 06:48:49PM +0000, Biju Das wrote:
> This patch series enable eMMC on SDHI0 and SDHI1 on SDHI2
>
> This patch series is depend upon [1]
> [1] https://lore.kernel.org/all/20261104-usb_rzg3l-v8-0-ab109c4bd108@bp.renesas.com/
>
> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
could you comment shortly on the Sashiko reports, please?
Thanks and happy hacking,
Wolfram
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 13+ messages in thread
* RE: [PATCH 0/3] Enable RZ/G3L SDHI
2026-11-16 10:05 ` [PATCH 0/3] Enable RZ/G3L SDHI Wolfram Sang
@ 2026-11-16 10:09 ` Biju Das
0 siblings, 0 replies; 13+ messages in thread
From: Biju Das @ 2026-11-16 10:09 UTC (permalink / raw)
To: wsa+renesas, biju.das.au
Cc: Geert Uytterhoeven, magnus.damm, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, linux-renesas-soc, devicetree,
linux-kernel
Hi Wolfram,
> -----Original Message-----
> From: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Sent: 16 November 2026 10:05
> Subject: Re: [PATCH 0/3] Enable RZ/G3L SDHI
>
> Hi Biju,
>
> On Thu, Nov 12, 2026 at 06:48:49PM +0000, Biju Das wrote:
> > This patch series enable eMMC on SDHI0 and SDHI1 on SDHI2
> >
> > This patch series is depend upon [1]
> > [1] https://lore.kernel.org/all/20261104-usb_rzg3l-v8-0-ab109c4bd108@bp.renesas.com/
> >
> > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
>
> could you comment shortly on the Sashiko reports, please?
Sure.
Cheers,
Biju
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK
2026-11-12 18:48 ` [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK Biju Das
@ 2026-11-20 12:52 ` Geert Uytterhoeven
2026-11-20 13:14 ` Biju Das
0 siblings, 1 reply; 13+ messages in thread
From: Geert Uytterhoeven @ 2026-11-20 12:52 UTC (permalink / raw)
To: Biju Das
Cc: Magnus Damm, Wolfram Sang, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-renesas-soc, devicetree, linux-kernel,
Biju Das
Hi Biju,
On Thu, 12 Nov 2026 at 19:48, Biju Das <biju.das.au@gmail.com> wrote:
> From: Biju Das <biju.das.jz@bp.renesas.com>
>
> Add device tree nodes for the three SDHI controllers (SDHI{0,1,2})
> on the RZ/G3L SoC (r9a08g046) and enable SDHI1 on the RZ/G3L SMARC
> EVK platform with pincontrol and GPIO-based voltage switching
> regulator support.
>
> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Thanks for your patch!
> --- a/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
> +++ b/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
> @@ -1062,9 +1062,80 @@ dmac: dma-controller@11820000 {
> dma-channels = <16>;
> };
>
> + sdhi0: mmc@11c00000 {
> + compatible = "renesas,sdhi-r9a08g046";
> + reg = <0x0 0x11c00000 0 0x10000>;
> + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cpg CPG_MOD R9A08G046_SDHI0_IMCLK>,
> + <&cpg CPG_MOD R9A08G046_SDHI0_CLK_HS>,
> + <&cpg CPG_MOD R9A08G046_SDHI0_IMCLK2>,
> + <&cpg CPG_MOD R9A08G046_SDHI0_IACLKM>,
> + <&cpg CPG_MOD R9A08G046_SDHI0_IACLKS>;
> + clock-names = "core", "clkh", "cd", "aclkm", "aclks";
> + max-frequency = <150000000>;
Given the bus clock can only run at 200, 100, 50, or 6.25 MHz,
150 Mhz looks strange to me.
> + resets = <&cpg R9A08G046_SDHI0_IXRST>,
> + <&cpg R9A08G046_SDHI0_IXRSTAXIM>,
> + <&cpg R9A08G046_SDHI0_IXRSTAXIS>;
> + reset-names = "rst", "axim", "axis";
> + power-domains = <&cpg>;
> + status = "disabled";
> + };
> +
> sdhi1: mmc@11c10000 {
> + compatible = "renesas,sdhi-r9a08g046";
> reg = <0x0 0x11c10000 0 0x10000>;
> - /* placeholder */
> + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cpg CPG_MOD R9A08G046_SDHI1_IMCLK>,
> + <&cpg CPG_MOD R9A08G046_SDHI1_CLK_HS>,
> + <&cpg CPG_MOD R9A08G046_SDHI1_IMCLK2>,
> + <&cpg CPG_MOD R9A08G046_SDHI1_IACLKM>,
> + <&cpg CPG_MOD R9A08G046_SDHI1_IACLKS>;
> + clock-names = "core", "clkh", "cd", "aclkm", "aclks";
> + max-frequency = <150000000>;
Likewise. This instance does not support HS400, but HS200 and HS400
use the same bus clock speed, right?
> + resets = <&cpg R9A08G046_SDHI1_IXRST>,
> + <&cpg R9A08G046_SDHI1_IXRSTAXIM>,
> + <&cpg R9A08G046_SDHI1_IXRSTAXIS>;
> + reset-names = "rst", "axim", "axis";
> + power-domains = <&cpg>;
> + status = "disabled";
> +
> + sdhi1_vqmmc: vqmmc-regulator {
> + regulator-name = "SDHI1-VQMMC";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <1200>;
> + status = "disabled";
> + };
> + };
> +
> + sdhi2: mmc@11c20000 {
> + compatible = "renesas,sdhi-r9a08g046";
> + reg = <0x0 0x11c20000 0 0x10000>;
> + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cpg CPG_MOD R9A08G046_SDHI2_IMCLK>,
> + <&cpg CPG_MOD R9A08G046_SDHI2_CLK_HS>,
> + <&cpg CPG_MOD R9A08G046_SDHI2_IMCLK2>,
> + <&cpg CPG_MOD R9A08G046_SDHI2_IACLKM>,
> + <&cpg CPG_MOD R9A08G046_SDHI2_IACLKS>;
> + clock-names = "core", "clkh", "cd", "aclkm", "aclks";
> + max-frequency = <150000000>;
This instance maxes out at SDR104, so max-frequency should be lower?
> + resets = <&cpg R9A08G046_SDHI2_IXRST>,
> + <&cpg R9A08G046_SDHI2_IXRSTAXIM>,
> + <&cpg R9A08G046_SDHI2_IXRSTAXIS>;
> + reset-names = "rst", "axim", "axis";
> + power-domains = <&cpg>;
> + status = "disabled";
> +
> + sdhi2_vqmmc: vqmmc-regulator {
> + regulator-name = "SDHI2-VQMMC";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <1200>;
> + status = "disabled";
> + };
> };
The rest LGTM.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 2/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0
2026-11-12 18:48 ` [PATCH 2/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0 Biju Das
@ 2026-11-20 13:04 ` Geert Uytterhoeven
0 siblings, 0 replies; 13+ messages in thread
From: Geert Uytterhoeven @ 2026-11-20 13:04 UTC (permalink / raw)
To: Biju Das
Cc: Magnus Damm, Wolfram Sang, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-renesas-soc, devicetree, linux-kernel,
Biju Das
Hi Biju,
On Thu, 12 Nov 2026 at 19:48, Biju Das <biju.das.au@gmail.com> wrote:
> From: Biju Das <biju.das.jz@bp.renesas.com>
>
> Add support for enabling SD card or eMMC on SDHI0 on the RZ/G3L SMARC
> SoM. The selection between SD and eMMC is controlled by the
> SW_SD0_DEV_SEL macro in the board DTS, which must match the position
> of switch SYS.1 on the SoM. By default, eMMC is enabled.
>
> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Thanks for your patch!
> --- a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
> +++ b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
> +
> + sdhi0_usd_pins: sd0-usd {
> + sd0-cd {
> + pinmux = <RZG2L_PORT_PINMUX(5, 0, 8)>; /* SD0_CD */
> + };
> + sdhi0_usd_uhs_pins: sd0-usd-uhs {
> + sd0-cd {
> + pinmux = <RZG2L_PORT_PINMUX(5, 0, 8)>; /* SD0_CD */
> + };
With s/RZG2L_PORT_PINMUX/RZG3L_PORT_PINMUX/g:
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 13+ messages in thread
* RE: [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK
2026-11-20 12:52 ` Geert Uytterhoeven
@ 2026-11-20 13:14 ` Biju Das
2026-11-20 13:22 ` Geert Uytterhoeven
0 siblings, 1 reply; 13+ messages in thread
From: Biju Das @ 2026-11-20 13:14 UTC (permalink / raw)
To: geert, biju.das.au
Cc: magnus.damm, wsa+renesas, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-renesas-soc, devicetree, linux-kernel
Hi Geert,
Thanks for the feedback
> -----Original Message-----
> From: Geert Uytterhoeven <geert@linux-m68k.org>
> Sent: 20 November 2026 12:52
> Subject: Re: [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1
> pincontrol on SMARC EVK
>
> Hi Biju,
>
> On Thu, 12 Nov 2026 at 19:48, Biju Das <biju.das.au@gmail.com> wrote:
> > From: Biju Das <biju.das.jz@bp.renesas.com>
> >
> > Add device tree nodes for the three SDHI controllers (SDHI{0,1,2}) on
> > the RZ/G3L SoC (r9a08g046) and enable SDHI1 on the RZ/G3L SMARC EVK
> > platform with pincontrol and GPIO-based voltage switching regulator
> > support.
> >
> > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
>
> Thanks for your patch!
>
> > --- a/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
> > +++ b/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
> > @@ -1062,9 +1062,80 @@ dmac: dma-controller@11820000 {
> > dma-channels = <16>;
> > };
> >
> > + sdhi0: mmc@11c00000 {
> > + compatible = "renesas,sdhi-r9a08g046";
> > + reg = <0x0 0x11c00000 0 0x10000>;
> > + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&cpg CPG_MOD R9A08G046_SDHI0_IMCLK>,
> > + <&cpg CPG_MOD R9A08G046_SDHI0_CLK_HS>,
> > + <&cpg CPG_MOD R9A08G046_SDHI0_IMCLK2>,
> > + <&cpg CPG_MOD R9A08G046_SDHI0_IACLKM>,
> > + <&cpg CPG_MOD R9A08G046_SDHI0_IACLKS>;
> > + clock-names = "core", "clkh", "cd", "aclkm", "aclks";
> > + max-frequency = <150000000>;
>
> Given the bus clock can only run at 200, 100, 50, or 6.25 MHz,
> 150 Mhz looks strange to me.
Ref: RZG3L_clock_list_r1.10_ad.xlsx
400 MHz IMCL{K,K2} clock is prohibited for this SoC.
800 MHz HS clock is prohibited for this SoC.
IMCLK = SD / 2
HS = SD
IMCLK clock sources
400 MHz:- Prohibited
300.000
250.000
133.333
The next available max frequency = 300 / 2 = 150 MHz that goes to
SD interface.
>
> > + resets = <&cpg R9A08G046_SDHI0_IXRST>,
> > + <&cpg R9A08G046_SDHI0_IXRSTAXIM>,
> > + <&cpg R9A08G046_SDHI0_IXRSTAXIS>;
> > + reset-names = "rst", "axim", "axis";
> > + power-domains = <&cpg>;
> > + status = "disabled";
> > + };
> > +
> > sdhi1: mmc@11c10000 {
> > + compatible = "renesas,sdhi-r9a08g046";
> > reg = <0x0 0x11c10000 0 0x10000>;
> > - /* placeholder */
> > + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&cpg CPG_MOD R9A08G046_SDHI1_IMCLK>,
> > + <&cpg CPG_MOD R9A08G046_SDHI1_CLK_HS>,
> > + <&cpg CPG_MOD R9A08G046_SDHI1_IMCLK2>,
> > + <&cpg CPG_MOD R9A08G046_SDHI1_IACLKM>,
> > + <&cpg CPG_MOD R9A08G046_SDHI1_IACLKS>;
> > + clock-names = "core", "clkh", "cd", "aclkm", "aclks";
> > + max-frequency = <150000000>;
>
> Likewise. This instance does not support HS400, but HS200 and HS400 use the same bus clock speed,
> right?
Yes that is correct, HS200 and HS400 use the same bus clock speed
for HS200 it is 1:1 option, so 300MHz and with internal divider(2) = 150 MHz
For HS400, Divider from SDctrl register=0, so 300MHz with SD_CTRL divider 2 =150 MHz.
>
> > + resets = <&cpg R9A08G046_SDHI1_IXRST>,
> > + <&cpg R9A08G046_SDHI1_IXRSTAXIM>,
> > + <&cpg R9A08G046_SDHI1_IXRSTAXIS>;
> > + reset-names = "rst", "axim", "axis";
> > + power-domains = <&cpg>;
> > + status = "disabled";
> > +
> > + sdhi1_vqmmc: vqmmc-regulator {
> > + regulator-name = "SDHI1-VQMMC";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-ramp-delay = <1200>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > + sdhi2: mmc@11c20000 {
> > + compatible = "renesas,sdhi-r9a08g046";
> > + reg = <0x0 0x11c20000 0 0x10000>;
> > + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&cpg CPG_MOD R9A08G046_SDHI2_IMCLK>,
> > + <&cpg CPG_MOD R9A08G046_SDHI2_CLK_HS>,
> > + <&cpg CPG_MOD R9A08G046_SDHI2_IMCLK2>,
> > + <&cpg CPG_MOD R9A08G046_SDHI2_IACLKM>,
> > + <&cpg CPG_MOD R9A08G046_SDHI2_IACLKS>;
> > + clock-names = "core", "clkh", "cd", "aclkm", "aclks";
> > + max-frequency = <150000000>;
>
> This instance maxes out at SDR104, so max-frequency should be lower?
SDR104 max frequency theoretical 208MHz.
In our SoC, 200 MHz is prohibited, so the next maximum available is 150MHz.
Cheers,
Biju
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2
2026-11-12 18:48 ` [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2 Biju Das
@ 2026-11-20 13:17 ` Geert Uytterhoeven
2026-11-20 13:22 ` Biju Das
0 siblings, 1 reply; 13+ messages in thread
From: Geert Uytterhoeven @ 2026-11-20 13:17 UTC (permalink / raw)
To: Biju Das
Cc: Magnus Damm, Wolfram Sang, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-renesas-soc, devicetree, linux-kernel,
Biju Das
Hi Biju,
On Thu, 12 Nov 2026 at 19:48, Biju Das <biju.das.au@gmail.com> wrote:
> From: Biju Das <biju.das.jz@bp.renesas.com>
>
> Enable SDHI2 on the RZ/G3L SMARC EVK platform using the internal
> voltage regulator for voltage switching. SDHI2 signals are muxed
> with I2S0; the selection is controlled by the SW_SD2_EN macro in
> the board DTS, which must match the position of switch SYS.4 on
> the SoM. By default, I2S0 is enabled.
>
> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
> --- a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
> +++ b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
> @@ -42,6 +42,7 @@ aliases {
> ethernet1 = ð1;
> i2c0 = &i2c0;
> mmc0 = &sdhi0;
> + mmc2 = &sdhi2;
> };
>
> memory@48000000 {
> @@ -355,6 +356,74 @@ sd0-data {
> power-source = <1800>;
> };
> };
> +
> + sdhi2_pins: sd2 {
> + sd2-pwen {
> + pinmux = <RZG3L_PORT_PINMUX(K, 2, 1)>; /* SD2_PWEN */
> + };
> + };
Just wondering: why do you use the internal voltage regulator for SD2
and GPIO hogs for SD0 and SD1?
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK
2026-11-20 13:14 ` Biju Das
@ 2026-11-20 13:22 ` Geert Uytterhoeven
0 siblings, 0 replies; 13+ messages in thread
From: Geert Uytterhoeven @ 2026-11-20 13:22 UTC (permalink / raw)
To: Biju Das
Cc: biju.das.au, magnus.damm, wsa+renesas, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, linux-renesas-soc, devicetree,
linux-kernel
Hi Biju,
On Fri, 20 Nov 2026 at 14:14, Biju Das <biju.das.jz@bp.renesas.com> wrote:
> > From: Geert Uytterhoeven <geert@linux-m68k.org>
> > On Thu, 12 Nov 2026 at 19:48, Biju Das <biju.das.au@gmail.com> wrote:
> > > From: Biju Das <biju.das.jz@bp.renesas.com>
> > >
> > > Add device tree nodes for the three SDHI controllers (SDHI{0,1,2}) on
> > > the RZ/G3L SoC (r9a08g046) and enable SDHI1 on the RZ/G3L SMARC EVK
> > > platform with pincontrol and GPIO-based voltage switching regulator
> > > support.
> > >
> > > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
> > > --- a/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
> > > +++ b/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
> > > @@ -1062,9 +1062,80 @@ dmac: dma-controller@11820000 {
> > > dma-channels = <16>;
> > > };
> > >
> > > + sdhi0: mmc@11c00000 {
> > > + compatible = "renesas,sdhi-r9a08g046";
> > > + reg = <0x0 0x11c00000 0 0x10000>;
> > > + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
> > > + <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
> > > + clocks = <&cpg CPG_MOD R9A08G046_SDHI0_IMCLK>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI0_CLK_HS>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI0_IMCLK2>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI0_IACLKM>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI0_IACLKS>;
> > > + clock-names = "core", "clkh", "cd", "aclkm", "aclks";
> > > + max-frequency = <150000000>;
> >
> > Given the bus clock can only run at 200, 100, 50, or 6.25 MHz,
> > 150 Mhz looks strange to me.
>
> Ref: RZG3L_clock_list_r1.10_ad.xlsx
> 400 MHz IMCL{K,K2} clock is prohibited for this SoC.
> 800 MHz HS clock is prohibited for this SoC.
>
> IMCLK = SD / 2
> HS = SD
>
> IMCLK clock sources
> 400 MHz:- Prohibited
> 300.000
> 250.000
> 133.333
>
>
> The next available max frequency = 300 / 2 = 150 MHz that goes to
> SD interface.
>
> >
> > > + resets = <&cpg R9A08G046_SDHI0_IXRST>,
> > > + <&cpg R9A08G046_SDHI0_IXRSTAXIM>,
> > > + <&cpg R9A08G046_SDHI0_IXRSTAXIS>;
> > > + reset-names = "rst", "axim", "axis";
> > > + power-domains = <&cpg>;
> > > + status = "disabled";
> > > + };
> > > +
> > > sdhi1: mmc@11c10000 {
> > > + compatible = "renesas,sdhi-r9a08g046";
> > > reg = <0x0 0x11c10000 0 0x10000>;
> > > - /* placeholder */
> > > + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
> > > + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> > > + clocks = <&cpg CPG_MOD R9A08G046_SDHI1_IMCLK>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI1_CLK_HS>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI1_IMCLK2>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI1_IACLKM>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI1_IACLKS>;
> > > + clock-names = "core", "clkh", "cd", "aclkm", "aclks";
> > > + max-frequency = <150000000>;
> >
> > Likewise. This instance does not support HS400, but HS200 and HS400 use the same bus clock speed,
> > right?
>
> Yes that is correct, HS200 and HS400 use the same bus clock speed
>
> for HS200 it is 1:1 option, so 300MHz and with internal divider(2) = 150 MHz
>
> For HS400, Divider from SDctrl register=0, so 300MHz with SD_CTRL divider 2 =150 MHz.
>
> >
> > > + resets = <&cpg R9A08G046_SDHI1_IXRST>,
> > > + <&cpg R9A08G046_SDHI1_IXRSTAXIM>,
> > > + <&cpg R9A08G046_SDHI1_IXRSTAXIS>;
> > > + reset-names = "rst", "axim", "axis";
> > > + power-domains = <&cpg>;
> > > + status = "disabled";
> > > +
> > > + sdhi1_vqmmc: vqmmc-regulator {
> > > + regulator-name = "SDHI1-VQMMC";
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-ramp-delay = <1200>;
> > > + status = "disabled";
> > > + };
> > > + };
> > > +
> > > + sdhi2: mmc@11c20000 {
> > > + compatible = "renesas,sdhi-r9a08g046";
> > > + reg = <0x0 0x11c20000 0 0x10000>;
> > > + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
> > > + <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
> > > + clocks = <&cpg CPG_MOD R9A08G046_SDHI2_IMCLK>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI2_CLK_HS>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI2_IMCLK2>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI2_IACLKM>,
> > > + <&cpg CPG_MOD R9A08G046_SDHI2_IACLKS>;
> > > + clock-names = "core", "clkh", "cd", "aclkm", "aclks";
> > > + max-frequency = <150000000>;
> >
> > This instance maxes out at SDR104, so max-frequency should be lower?
>
> SDR104 max frequency theoretical 208MHz.
>
> In our SoC, 200 MHz is prohibited, so the next maximum available is 150MHz.
OK.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 13+ messages in thread
* RE: [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2
2026-11-20 13:17 ` Geert Uytterhoeven
@ 2026-11-20 13:22 ` Biju Das
2026-11-20 13:23 ` Geert Uytterhoeven
0 siblings, 1 reply; 13+ messages in thread
From: Biju Das @ 2026-11-20 13:22 UTC (permalink / raw)
To: geert, biju.das.au
Cc: magnus.damm, wsa+renesas, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-renesas-soc, devicetree, linux-kernel
Hi Geert,
> -----Original Message-----
> From: Geert Uytterhoeven <geert@linux-m68k.org>
> Sent: 20 November 2026 13:17
> Subject: Re: [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2
>
> Hi Biju,
>
> On Thu, 12 Nov 2026 at 19:48, Biju Das <biju.das.au@gmail.com> wrote:
> > From: Biju Das <biju.das.jz@bp.renesas.com>
> >
> > Enable SDHI2 on the RZ/G3L SMARC EVK platform using the internal
> > voltage regulator for voltage switching. SDHI2 signals are muxed with
> > I2S0; the selection is controlled by the SW_SD2_EN macro in the board
> > DTS, which must match the position of switch SYS.4 on the SoM. By
> > default, I2S0 is enabled.
> >
> > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
>
> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
>
> > --- a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
> > +++ b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
> > @@ -42,6 +42,7 @@ aliases {
> > ethernet1 = ð1;
> > i2c0 = &i2c0;
> > mmc0 = &sdhi0;
> > + mmc2 = &sdhi2;
> > };
> >
> > memory@48000000 {
> > @@ -355,6 +356,74 @@ sd0-data {
> > power-source = <1800>;
> > };
> > };
> > +
> > + sdhi2_pins: sd2 {
>
> > + sd2-pwen {
> > + pinmux = <RZG3L_PORT_PINMUX(K, 2, 1)>; /* SD2_PWEN */
> > + };
> > + };
>
> Just wondering: why do you use the internal voltage regulator for SD2 and GPIO hogs for SD0 and SD1?
Just to give an example for the customer usage. Either use GPIO or internal regulator
both are supported in driver.
Cheers,
Biju
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2
2026-11-20 13:22 ` Biju Das
@ 2026-11-20 13:23 ` Geert Uytterhoeven
0 siblings, 0 replies; 13+ messages in thread
From: Geert Uytterhoeven @ 2026-11-20 13:23 UTC (permalink / raw)
To: Biju Das
Cc: biju.das.au, magnus.damm, wsa+renesas, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, linux-renesas-soc, devicetree,
linux-kernel
Hi Biju,
On Fri, 20 Nov 2026 at 14:22, Biju Das <biju.das.jz@bp.renesas.com> wrote:
> > From: Geert Uytterhoeven <geert@linux-m68k.org>
> > On Thu, 12 Nov 2026 at 19:48, Biju Das <biju.das.au@gmail.com> wrote:
> > > From: Biju Das <biju.das.jz@bp.renesas.com>
> > >
> > > Enable SDHI2 on the RZ/G3L SMARC EVK platform using the internal
> > > voltage regulator for voltage switching. SDHI2 signals are muxed with
> > > I2S0; the selection is controlled by the SW_SD2_EN macro in the board
> > > DTS, which must match the position of switch SYS.4 on the SoM. By
> > > default, I2S0 is enabled.
> > >
> > > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
> >
> > Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
> >
> > > --- a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
> > > +++ b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
> > > @@ -42,6 +42,7 @@ aliases {
> > > ethernet1 = ð1;
> > > i2c0 = &i2c0;
> > > mmc0 = &sdhi0;
> > > + mmc2 = &sdhi2;
> > > };
> > >
> > > memory@48000000 {
> > > @@ -355,6 +356,74 @@ sd0-data {
> > > power-source = <1800>;
> > > };
> > > };
> > > +
> > > + sdhi2_pins: sd2 {
> >
> > > + sd2-pwen {
> > > + pinmux = <RZG3L_PORT_PINMUX(K, 2, 1)>; /* SD2_PWEN */
> > > + };
> > > + };
> >
> > Just wondering: why do you use the internal voltage regulator for SD2 and GPIO hogs for SD0 and SD1?
>
> Just to give an example for the customer usage. Either use GPIO or internal regulator
> both are supported in driver.
OK. Please clarify in a comment.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2026-11-20 13:23 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-11-12 18:48 [PATCH 0/3] Enable RZ/G3L SDHI Biju Das
2026-11-12 18:48 ` [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK Biju Das
2026-11-20 12:52 ` Geert Uytterhoeven
2026-11-20 13:14 ` Biju Das
2026-11-20 13:22 ` Geert Uytterhoeven
2026-11-12 18:48 ` [PATCH 2/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0 Biju Das
2026-11-20 13:04 ` Geert Uytterhoeven
2026-11-12 18:48 ` [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2 Biju Das
2026-11-20 13:17 ` Geert Uytterhoeven
2026-11-20 13:22 ` Biju Das
2026-11-20 13:23 ` Geert Uytterhoeven
2026-11-16 10:05 ` [PATCH 0/3] Enable RZ/G3L SDHI Wolfram Sang
2026-11-16 10:09 ` Biju Das
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®