From: Sakari Ailus <sakari.ailus@linux.intel.com>
To: "André Apitzsch" <git@apitzsch.eu>
Cc: Ricardo Ribalda Delgado <ribalda@kernel.org>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
~postmarketos/upstreaming@lists.sr.ht,
phone-devel@vger.kernel.org, linux-media@vger.kernel.org,
linux-kernel@vger.kernel.org,
Dave Stevenson <dave.stevenson@raspberrypi.com>,
Vincent Knecht <vincent.knecht@mailoo.org>
Subject: Re: [PATCH v3 07/12] media: i2c: imx214: Add vblank and hblank controls
Date: Sun, 15 Dec 2024 12:10:30 +0000 [thread overview]
Message-ID: <Z17HNqjz4ecL3fiU@kekkonen.localdomain> (raw)
In-Reply-To: <8255eb1a877a339a457979c8b4fc831f6fc5cc01.camel@apitzsch.eu>
Hi André,
On Sat, Dec 14, 2024 at 11:45:16PM +0100, André Apitzsch wrote:
> Hi,
>
> Am Dienstag, dem 10.12.2024 um 12:34 +0000 schrieb Sakari Ailus:
> > On Sun, Dec 08, 2024 at 10:19:51PM +0100, Ricardo Ribalda Delgado
> > wrote:
> > > > > + state =
> > > > > v4l2_subdev_get_locked_active_state(&imx214->sd);
> > > >
> > > > Sakari, I see that other drivers assume that the active is locked
> > > > in
> > > > set_ctrl. Is this correct?
> > >
> > > imx214->sd.state_lock = imx214->ctrls.lock;
> > >
> > > So I guess it is fine :)
> >
> > Yes, it is.
> >
> > Please also run this on the set:
> >
> > $ ./scripts/checkpatch.pl --strict --max-line-length=80
> >
>
> there are a few lines that exceed 80 columns:
>
> WARNING: line length of 85 exceeds 80 columns
> #163: FILE: drivers/media/i2c/imx214.c:576:
> + imx214_update_pad_format(imx214, mode, &format->format, format->format.code);
> --
> WARNING: line length of 81 exceeds 80 columns
> #88: FILE: drivers/media/i2c/imx214.c:983:
> + return dev_err_probe(dev, ret, "failed to set xclk frequency\n");
> --
> WARNING: line length of 82 exceeds 80 columns
> #138: FILE: drivers/media/i2c/imx214.c:1039:
> + dev_err_probe(dev, ret, "failed to register sensor sub-device\n");
> --
> WARNING: line length of 86 exceeds 80 columns
> #491: FILE: drivers/media/i2c/imx214.c:359:
> + { IMX214_REG_EXCK_FREQ, IMX214_EXCK_FREQ(IMX214_DEFAULT_CLK_FREQ / 1000000) },
> --
> WARNING: line length of 83 exceeds 80 columns
> #177: FILE: drivers/media/i2c/imx214.c:730:
> + exposure_max = format->height + ctrl->val - IMX214_EXPOSURE_OFFSET;
> --
> WARNING: line length of 85 exceeds 80 columns
> #85: FILE: drivers/media/i2c/imx214.c:1231:
> + if (bus_cfg.link_frequencies[i] == IMX214_DEFAULT_LINK_FREQ_LEGACY) {
>
>
> Is the strict 80 columns limit really necessary, as it would decrease
> readability?
For the array that could be the case but I think I'd wrap the rest.
--
Regards,
Sakari Ailus
next prev parent reply other threads:[~2024-12-15 12:10 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-12-07 20:47 [PATCH v3 00/12] media: i2c: imx214: Miscellaneous cleanups and improvements André Apitzsch via B4 Relay
2024-12-07 20:47 ` [PATCH v3 01/12] media: i2c: imx214: Use subdev active state André Apitzsch via B4 Relay
2024-12-07 20:47 ` [PATCH v3 02/12] media: i2c: imx214: Simplify with dev_err_probe() André Apitzsch via B4 Relay
2024-12-07 20:47 ` [PATCH v3 03/12] media: i2c: imx214: Convert to CCI register access helpers André Apitzsch via B4 Relay
2024-12-07 20:47 ` [PATCH v3 04/12] media: i2c: imx214: Replace register addresses with macros André Apitzsch via B4 Relay
2024-12-07 20:47 ` [PATCH v3 05/12] media: i2c: imx214: Drop IMX214_REG_EXPOSURE from mode reg arrays André Apitzsch via B4 Relay
2024-12-07 20:47 ` [PATCH v3 06/12] media: i2c: imx214: Check number of lanes from device tree André Apitzsch via B4 Relay
2024-12-08 21:07 ` Ricardo Ribalda Delgado
2024-12-10 12:35 ` Sakari Ailus
2024-12-07 20:47 ` [PATCH v3 07/12] media: i2c: imx214: Add vblank and hblank controls André Apitzsch via B4 Relay
2024-12-08 20:59 ` Ricardo Ribalda Delgado
2024-12-08 21:19 ` Ricardo Ribalda Delgado
2024-12-10 12:34 ` Sakari Ailus
2024-12-14 22:45 ` André Apitzsch
2024-12-15 12:10 ` Sakari Ailus [this message]
2024-12-08 21:35 ` André Apitzsch
2024-12-08 21:47 ` Ricardo Ribalda Delgado
2024-12-15 22:35 ` André Apitzsch
2024-12-16 13:00 ` Ricardo Ribalda Delgado
2024-12-17 7:17 ` Sakari Ailus
2024-12-07 20:47 ` [PATCH v3 08/12] media: i2c: imx214: Implement vflip/hflip controls André Apitzsch via B4 Relay
2024-12-07 20:47 ` [PATCH v3 09/12] media: i2c: imx214: Add analogue/digital gain control André Apitzsch via B4 Relay
2024-12-07 20:47 ` [PATCH v3 10/12] media: i2c: imx214: Verify chip ID André Apitzsch via B4 Relay
2024-12-10 12:40 ` Sakari Ailus
2024-12-07 20:48 ` [PATCH v3 11/12] media: i2c: imx214: Add test pattern control André Apitzsch via B4 Relay
2024-12-07 20:48 ` [PATCH v3 12/12] media: i2c: imx214: Fix link frequency André Apitzsch via B4 Relay
2024-12-08 21:05 ` Ricardo Ribalda Delgado
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Z17HNqjz4ecL3fiU@kekkonen.localdomain \
--to=sakari.ailus@linux.intel.com \
--cc=dave.stevenson@raspberrypi.com \
--cc=git@apitzsch.eu \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=phone-devel@vger.kernel.org \
--cc=ribalda@kernel.org \
--cc=vincent.knecht@mailoo.org \
--cc=~postmarketos/upstreaming@lists.sr.ht \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®