[PATCH v3 0/3] arm64: dts: imx8mm-var-dart: update SoM support

[PATCH v3 0/3] arm64: dts: imx8mm-var-dart: update SoM support

[Stefano Radaelli]

This series updates the Variscite DART-MX8M-MINI SoM device tree to
better reflect the currently supported hardware configuration.

The changes configure SAI3 in synchronous RX mode, add TPM support,
and increase the Ethernet PHY reset deassert delay to improve PHY
detection reliability.

v2->v3:
 - Fixed reset-gpio polarity

v1->v2:
 - Add tpm pinctrl
 - Add comment on tpm reset line

Stefano Radaelli (3):
  arm64: dts: imx8mm-var-dart: configure SAI3 synchronous RX mode
  arm64: dts: imx8mm-var-dart: add TPM support
  arm64: dts: imx8mm-var-dart: increase PHY reset deassert delay

 .../boot/dts/freescale/imx8mm-var-dart.dtsi   | 21 ++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)


base-commit: 46d8fa682d263271f3ef7bf95166b124c19d6c62
-- 
2.47.3

[PATCH v3 1/3] arm64: dts: imx8mm-var-dart: configure SAI3 synchronous RX mode

[Stefano Radaelli]

From: Stefano Radaelli <stefano.r@variscite.com>

Configure SAI3 to operate in synchronous RX mode, so that the trasmit
path uses the receive bit clock and frame sync signals.

Remove the TX_SYNC and TX_BCLK pinmux entries, as these signals are not
used in this configuration.

Co-developed-by: Francesco Ferraro <francesco.f@variscite.com>
Signed-off-by: Francesco Ferraro <francesco.f@variscite.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
---
v2->v3:
 - 

v1->v2:
 - 

 arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi
index 2324063f8fd9..c7a9eb23e5e8 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi
@@ -305,6 +305,7 @@ &sai3 {
 	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
 	assigned-clock-rates = <1536000>;
 	fsl,sai-mclk-direction-output;
+	fsl,sai-synchronous-rx;
 	status = "okay";
 };
 
@@ -446,8 +447,6 @@ pinctrl_sai3: sai3grp {
 			MX8MM_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC		0xd6
 			MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK		0xd6
 			MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0		0xd6
-			MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC		0xd6
-			MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK		0xd6
 			MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0		0xd6
 			MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK		0xd6
 		>;
-- 
2.47.3

[PATCH v3 2/3] arm64: dts: imx8mm-var-dart: add TPM support

[Stefano Radaelli]

From: Stefano Radaelli <stefano.r@variscite.com>

Add support for the TPM available on the Variscite DART-MX8M-MINI SOM.

Co-developed-by: Nate Drude <nate.d@variscite.com>
Signed-off-by: Nate Drude <nate.d@variscite.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
---
v2->v3:
 - Fixed reset-gpio polarity

v1->v2:
 - Add tpm pinctrl
 - Add comment on tpm reset line

 .../boot/dts/freescale/imx8mm-var-dart.dtsi      | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi
index c7a9eb23e5e8..cb7998616a87 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi
@@ -138,6 +138,16 @@ &i2c1 {
 	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
+	st33ktpm2xi2c_som: tpm@2e {
+		compatible = "st,st33ktpm2xi2c", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tpm_reset>;
+		label = "tpm";
+		/* active-low TPM reset line. */
+		reset-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>;
+	};
+
 	pmic@4b {
 		compatible = "rohm,bd71847";
 		reg = <0x4b>;
@@ -452,6 +462,12 @@ MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK		0xd6
 		>;
 	};
 
+	pinctrl_tpm_reset: tpm-resetgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_GPIO4_IO31		0x19
+		>;
+	};
+
 	pinctrl_uart4: uart4grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX		0x140
-- 
2.47.3

[PATCH v3 3/3] arm64: dts: imx8mm-var-dart: increase PHY reset deassert delay

[Stefano Radaelli]

From: Stefano Radaelli <stefano.r@variscite.com>

The Ethernet PHY reset signal also controls the regulators supplying
VDDA2P5 and VDD1P0, so releasing reset restores the PHY's 2.5 V and
1.0 V analog supplies.

The existing 100 ms reset deassertion delay is not sufficient for
reliable PHY detection. The TI DP83867 requires 200 ms of stabilization
after power-up before MDIO register access.

Increase the reset deassertion delay to 200 ms to ensure reliable PHY
detection across repeated boots.

Co-developed-by: Nate Drude <nate.d@variscite.com>
Signed-off-by: Nate Drude <nate.d@variscite.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
---
v2->v3:
 - 

v1->v2:
 - 

 arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi
index cb7998616a87..c5f0e22f549b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-dart.dtsi
@@ -123,7 +123,7 @@ ethphy0: ethernet-phy@0 {
 			reg = <0>;
 			reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10000>;
-			reset-deassert-us = <100000>;
+			reset-deassert-us = <200000>;
 			vddio-supply = <&reg_phy_vddio>;
 		};
 	};
-- 
2.47.3