[PATCH v2 12/17] ARM: dts: samsung: exynos4210-trats: sort properties

[Henrik Grimler <henrik.grimler@axis.com>]

And add or delete newlines where applicable, and sort properties
according to the preferred style. Fixes warnings from dt-check-style
like:

  samsung/exynos4210-trats.dts:122: [property-order] property 'label' out of canonical order (should sort before 'linux,code')
  samsung/exynos4210-trats.dts:179: [required-blank-lines] "status" must be preceded by a blank line
  samsung/exynos4210-trats.dts:183: [property-order] property 'compatible' out of canonical order (should sort before 'reg')

Signed-off-by: Henrik Grimler <henrik.grimler@axis.com>
---
 arch/arm/boot/dts/samsung/exynos4210-trats.dts | 60 ++++++++++++++++----------
 1 file changed, 38 insertions(+), 22 deletions(-)

diff --git a/arch/arm/boot/dts/samsung/exynos4210-trats.dts b/arch/arm/boot/dts/samsung/exynos4210-trats.dts
index 20fe148387fc..8d4ebcf86775 100644
--- a/arch/arm/boot/dts/samsung/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/samsung/exynos4210-trats.dts
@@ -96,31 +96,31 @@ gpio-keys {
 
 		vol-down-key {
 			gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
-			linux,code = <114>;
 			label = "volume down";
 			debounce-interval = <10>;
+			linux,code = <114>;
 		};
 
 		vol-up-key {
 			gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
-			linux,code = <115>;
 			label = "volume up";
 			debounce-interval = <10>;
+			linux,code = <115>;
 		};
 
 		power-key {
 			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
-			linux,code = <116>;
 			label = "power";
 			debounce-interval = <10>;
 			wakeup-source;
+			linux,code = <116>;
 		};
 
 		ok-key {
 			gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
-			linux,code = <352>;
 			label = "ok";
 			debounce-interval = <10>;
+			linux,code = <352>;
 		};
 	};
 
@@ -163,6 +163,7 @@ map0 {
 			/* Corresponds to 800MHz at freq_table */
 			cooling-device = <&cpu0 2 2>, <&cpu1 2 2>;
 		};
+
 		map1 {
 			/* Corresponds to 200MHz at freq_table */
 			cooling-device = <&cpu0 4 4>, <&cpu1 4 4>;
@@ -176,11 +177,12 @@ &dsi_0 {
 	samsung,burst-clock-frequency = <500000000>;
 	samsung,esc-clock-frequency = <20000000>;
 	samsung,pll-clock-frequency = <24000000>;
+
 	status = "okay";
 
 	panel@0 {
-		reg = <0>;
 		compatible = "samsung,s6e8aa0";
+		reg = <0>;
 		vdd3-supply = <&vcclcd_reg>;
 		vci-supply = <&vlcd_reg>;
 		reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
@@ -209,40 +211,45 @@ timing-0 {
 };
 
 &exynos_usbphy {
-	status = "okay";
 	vbus-supply = <&safe1_sreg>;
+
+	status = "okay";
 };
 
 &fimc_0 {
-	status = "okay";
 	assigned-clocks = <&clock CLK_MOUT_FIMC0>,
 			  <&clock CLK_SCLK_FIMC0>;
 	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
 	assigned-clock-rates = <0>, <160000000>;
+
+	status = "okay";
 };
 
 &fimc_1 {
-	status = "okay";
 	assigned-clocks = <&clock CLK_MOUT_FIMC1>,
 			  <&clock CLK_SCLK_FIMC1>;
 	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
 	assigned-clock-rates = <0>, <160000000>;
+
+	status = "okay";
 };
 
 &fimc_2 {
-	status = "okay";
 	assigned-clocks = <&clock CLK_MOUT_FIMC2>,
 			  <&clock CLK_SCLK_FIMC2>;
 	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
-		assigned-clock-rates = <0>, <160000000>;
+	assigned-clock-rates = <0>, <160000000>;
+
+	status = "okay";
 };
 
 &fimc_3 {
-	status = "okay";
 	assigned-clocks = <&clock CLK_MOUT_FIMC3>,
 			  <&clock CLK_SCLK_FIMC3>;
 	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
 	assigned-clock-rates = <0>, <160000000>;
+
+	status = "okay";
 };
 
 &fimd {
@@ -257,15 +264,18 @@ &hsotg {
 	vusb_d-supply = <&vusb_reg>;
 	vusb_a-supply = <&vusbdac_reg>;
 	dr_mode = "peripheral";
+
 	status = "okay";
 };
 
 &i2c_3 {
+	pinctrl-0 = <&i2c3_bus>;
+	pinctrl-names = "default";
+
 	samsung,i2c-sda-delay = <100>;
 	samsung,i2c-slave-addr = <0x10>;
 	samsung,i2c-max-bus-freq = <400000>;
-	pinctrl-0 = <&i2c3_bus>;
-	pinctrl-names = "default";
+
 	status = "okay";
 
 	touchscreen@48 {
@@ -281,11 +291,13 @@ touchscreen@48 {
 };
 
 &i2c_5 {
+	pinctrl-0 = <&i2c5_bus>;
+	pinctrl-names = "default";
+
 	samsung,i2c-sda-delay = <100>;
 	samsung,i2c-slave-addr = <0x10>;
 	samsung,i2c-max-bus-freq = <100000>;
-	pinctrl-0 = <&i2c5_bus>;
-	pinctrl-names = "default";
+
 	status = "okay";
 
 	pmic@66 {
@@ -312,9 +324,9 @@ pmic@66 {
 						 <1000000>, <950000>;
 
 		max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
-						 <950000>,  <900000>,
+						 <950000>, <900000>,
 						 <1100000>, <1000000>,
-						 <950000>,  <900000>;
+						 <950000>, <900000>;
 
 		max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
 						 <1200000>, <1200000>,
@@ -488,9 +500,10 @@ bt_device_wakeup: bt-device-wakeup-pins {
 };
 
 &rtc {
-	status = "okay";
 	clocks = <&clock CLK_RTC>, <&pmic_ap_clk>;
 	clock-names = "rtc", "rtc_src";
+
+	status = "okay";
 };
 
 &sdhci_0 {
@@ -499,6 +512,7 @@ &sdhci_0 {
 	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
 	pinctrl-names = "default";
 	vmmc-supply = <&vemmc_reg>;
+
 	status = "okay";
 };
 
@@ -508,12 +522,11 @@ &sdhci_2 {
 	pinctrl-names = "default";
 	vmmc-supply = <&tflash_reg>;
 	cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
+
 	status = "okay";
 };
 
 &sdhci_3 {
-	status = "okay";
-
 	#address-cells = <1>;
 	#size-cells = <0>;
 
@@ -523,8 +536,10 @@ &sdhci_3 {
 	mmc-pwrseq = <&wlan_pwrseq>;
 	vmmc-supply = <&tflash_reg>;
 
-	pinctrl-names = "default";
 	pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
+	pinctrl-names = "default";
+
+	status = "okay";
 
 	brcmf: wifi@1 {
 		compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
@@ -537,12 +552,13 @@ brcmf: wifi@1 {
 };
 
 &serial_0 {
-	status = "okay";
 	pinctrl-0 = <&uart0_data &uart0_fctl>;
 	pinctrl-names = "default";
 
 	uart-has-rtscts;
 
+	status = "okay";
+
 	bluetooth {
 		compatible = "brcm,bcm4330-bt";
 

-- 
2.43.0