[0/3] Cooperate with DSI RX devices to modify dsi funcs and delay mipi high to cooperate with panel sequence

[0/3] Cooperate with DSI RX devices to modify dsi funcs and delay mipi high to cooperate with panel sequence

[xinlei.lee]

From: xinlei lee <xinlei.lee@mediatek.com>

In order to match the changes of DSI RX devices (for example, anx7625), 
the poweron/poweroff of dsi is extracted from enable/disable and 
defined as new funcs (pre_enable/post_disable).

The delayed MIPI signal is pulled high from LP00 to LP11, 
in order to match the power-on sequence of the panel.

Jitao Shi (3):
  drm/mediatek: dsi fine tune the dsi poweron flow
  drm/mediatek: dsi bridge implement pre_enable and post_disable
  drm/mediatek: keep dsi as LP00 before dcs cmds transfer

 drivers/gpu/drm/mediatek/mtk_dsi.c | 73 +++++++++++++++++++++++++-------------
 1 file changed, 49 insertions(+), 24 deletions(-)

-- 
2.6.4

[1/3] drm/mediatek: Adjust the timing of mipi signal from LP00 to LP11

[xinlei.lee]

From: Jitao Shi <jitao.shi@mediatek.com>

In order to cooperate with patch 3/3 modification,it is necessary to adjust 
the position where mipi pulls up the signal.

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dsi.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c
index 5d90d2eb..6d7b66d 100644
--- a/drivers/gpu/drm/mediatek/mtk_dsi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
@@ -649,14 +649,14 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
 	mtk_dsi_reset_engine(dsi);
 	mtk_dsi_phy_timconfig(dsi);
 
-	mtk_dsi_rxtx_control(dsi);
-	usleep_range(30, 100);
-	mtk_dsi_reset_dphy(dsi);
 	mtk_dsi_ps_control_vact(dsi);
 	mtk_dsi_set_vm_cmd(dsi);
 	mtk_dsi_config_vdo_timing(dsi);
 	mtk_dsi_set_interrupt_enable(dsi);
 
+	mtk_dsi_rxtx_control(dsi);
+	usleep_range(30, 100);
+	mtk_dsi_reset_dphy(dsi);
 	mtk_dsi_clk_ulp_mode_leave(dsi);
 	mtk_dsi_lane0_ulp_mode_leave(dsi);
 	mtk_dsi_clk_hs_mode(dsi, 0);
-- 
2.6.4

Re: [1/3] drm/mediatek: Adjust the timing of mipi signal from LP00 to LP11

[CK Hu]

Hi, Xinlei:

On Fri, 2022-02-11 at 22:30 +0800, xinlei.lee@mediatek.com wrote:
> From: Jitao Shi <jitao.shi@mediatek.com>
> 
> In order to cooperate with patch 3/3 modification,it is necessary to
> adjust 
> the position where mipi pulls up the signal.

After the patch is applied, the series index (3/3) is disappear, so do
not reference series index in commit description. I think this series
is to adjust the calling sequence, so you could describe as below:

Old sequence:
1. aaa
2. bbb
3. ccc
4. ddd

New sequence:
1. bbb
2. aaa
3. ddd
4. ccc

and this patch is to adjust 'aaa' and 'bbb'.

Regards,
CK

> 
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dsi.c | 6 +++---
>  1 file changed, 3 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c
> b/drivers/gpu/drm/mediatek/mtk_dsi.c
> index 5d90d2eb..6d7b66d 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dsi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
> @@ -649,14 +649,14 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
>  	mtk_dsi_reset_engine(dsi);
>  	mtk_dsi_phy_timconfig(dsi);
>  
> -	mtk_dsi_rxtx_control(dsi);
> -	usleep_range(30, 100);
> -	mtk_dsi_reset_dphy(dsi);
>  	mtk_dsi_ps_control_vact(dsi);
>  	mtk_dsi_set_vm_cmd(dsi);
>  	mtk_dsi_config_vdo_timing(dsi);
>  	mtk_dsi_set_interrupt_enable(dsi);
>  
> +	mtk_dsi_rxtx_control(dsi);
> +	usleep_range(30, 100);
> +	mtk_dsi_reset_dphy(dsi);
>  	mtk_dsi_clk_ulp_mode_leave(dsi);
>  	mtk_dsi_lane0_ulp_mode_leave(dsi);
>  	mtk_dsi_clk_hs_mode(dsi, 0);

[2/3] drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs

[xinlei.lee]

From: Jitao Shi <jitao.shi@mediatek.com>

In order to match the changes of DSI RX devices (for example, anx7625), 
the poweron/poweroff of dsi is extracted from enable/disable and 
defined as new funcs (pre_enable/post_disable).

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dsi.c | 45 ++++++++++++++++++++++----------------
 1 file changed, 26 insertions(+), 19 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c
index 6d7b66d..e47c338 100644
--- a/drivers/gpu/drm/mediatek/mtk_dsi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
@@ -679,16 +679,6 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
 	if (--dsi->refcount != 0)
 		return;
 
-	/*
-	 * mtk_dsi_stop() and mtk_dsi_start() is asymmetric, since
-	 * mtk_dsi_stop() should be called after mtk_drm_crtc_atomic_disable(),
-	 * which needs irq for vblank, and mtk_dsi_stop() will disable irq.
-	 * mtk_dsi_start() needs to be called in mtk_output_dsi_enable(),
-	 * after dsi is fully set.
-	 */
-	mtk_dsi_stop(dsi);
-
-	mtk_dsi_switch_to_cmd_mode(dsi, VM_DONE_INT_FLAG, 500);
 	mtk_dsi_reset_engine(dsi);
 	mtk_dsi_lane0_ulp_mode_enter(dsi);
 	mtk_dsi_clk_ulp_mode_enter(dsi);
@@ -703,17 +693,9 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
 
 static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
 {
-	int ret;
-
 	if (dsi->enabled)
 		return;
 
-	ret = mtk_dsi_poweron(dsi);
-	if (ret < 0) {
-		DRM_ERROR("failed to power on dsi\n");
-		return;
-	}
-
 	mtk_dsi_set_mode(dsi);
 	mtk_dsi_clk_hs_mode(dsi, 1);
 
@@ -727,7 +709,16 @@ static void mtk_output_dsi_disable(struct mtk_dsi *dsi)
 	if (!dsi->enabled)
 		return;
 
-	mtk_dsi_poweroff(dsi);
+	/*
+	 * mtk_dsi_stop() and mtk_dsi_start() is asymmetric, since
+	 * mtk_dsi_stop() should be called after mtk_drm_crtc_atomic_disable(),
+	 * which needs irq for vblank, and mtk_dsi_stop() will disable irq.
+	 * mtk_dsi_start() needs to be called in mtk_output_dsi_enable(),
+	 * after dsi is fully set.
+	 */
+	mtk_dsi_stop(dsi);
+
+	mtk_dsi_switch_to_cmd_mode(dsi, VM_DONE_INT_FLAG, 500);
 
 	dsi->enabled = false;
 }
@@ -765,10 +756,26 @@ static void mtk_dsi_bridge_enable(struct drm_bridge *bridge)
 	mtk_output_dsi_enable(dsi);
 }
 
+static void mtk_dsi_bridge_pre_enable(struct drm_bridge *bridge)
+{
+	struct mtk_dsi *dsi = bridge_to_dsi(bridge);
+
+	mtk_dsi_poweron(dsi);
+}
+
+static void mtk_dsi_bridge_post_disable(struct drm_bridge *bridge)
+{
+	struct mtk_dsi *dsi = bridge_to_dsi(bridge);
+
+	mtk_dsi_poweroff(dsi);
+}
+
 static const struct drm_bridge_funcs mtk_dsi_bridge_funcs = {
 	.attach = mtk_dsi_bridge_attach,
 	.disable = mtk_dsi_bridge_disable,
 	.enable = mtk_dsi_bridge_enable,
+	.pre_enable = mtk_dsi_bridge_pre_enable,
+	.post_disable = mtk_dsi_bridge_post_disable,
 	.mode_set = mtk_dsi_bridge_mode_set,
 };
 
-- 
2.6.4

Re: [2/3] drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs

[CK Hu]

Hi, Xinlei:

On Fri, 2022-02-11 at 22:30 +0800, xinlei.lee@mediatek.com wrote:
> From: Jitao Shi <jitao.shi@mediatek.com>
> 
> In order to match the changes of DSI RX devices (for example,
> anx7625), 
> the poweron/poweroff of dsi is extracted from enable/disable and 
> defined as new funcs (pre_enable/post_disable).

Does DSI not work with anx7625 now? This patch is a bug-fix or new
feature? If this patch is a bug-fix, please add 'Fixes' tag [1].

[1] 
https://www.kernel.org/doc/html/v5.16/process/submitting-patches.html

Regards,
CK

> 
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dsi.c | 45 ++++++++++++++++++++++----
> ------------
>  1 file changed, 26 insertions(+), 19 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c
> b/drivers/gpu/drm/mediatek/mtk_dsi.c
> index 6d7b66d..e47c338 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dsi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
> @@ -679,16 +679,6 @@ static void mtk_dsi_poweroff(struct mtk_dsi
> *dsi)
>  	if (--dsi->refcount != 0)
>  		return;
>  
> -	/*
> -	 * mtk_dsi_stop() and mtk_dsi_start() is asymmetric, since
> -	 * mtk_dsi_stop() should be called after
> mtk_drm_crtc_atomic_disable(),
> -	 * which needs irq for vblank, and mtk_dsi_stop() will disable
> irq.
> -	 * mtk_dsi_start() needs to be called in
> mtk_output_dsi_enable(),
> -	 * after dsi is fully set.
> -	 */
> -	mtk_dsi_stop(dsi);
> -
> -	mtk_dsi_switch_to_cmd_mode(dsi, VM_DONE_INT_FLAG, 500);
>  	mtk_dsi_reset_engine(dsi);
>  	mtk_dsi_lane0_ulp_mode_enter(dsi);
>  	mtk_dsi_clk_ulp_mode_enter(dsi);
> @@ -703,17 +693,9 @@ static void mtk_dsi_poweroff(struct mtk_dsi
> *dsi)
>  
>  static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
>  {
> -	int ret;
> -
>  	if (dsi->enabled)
>  		return;
>  
> -	ret = mtk_dsi_poweron(dsi);
> -	if (ret < 0) {
> -		DRM_ERROR("failed to power on dsi\n");
> -		return;
> -	}
> -
>  	mtk_dsi_set_mode(dsi);
>  	mtk_dsi_clk_hs_mode(dsi, 1);
>  
> @@ -727,7 +709,16 @@ static void mtk_output_dsi_disable(struct
> mtk_dsi *dsi)
>  	if (!dsi->enabled)
>  		return;
>  
> -	mtk_dsi_poweroff(dsi);
> +	/*
> +	 * mtk_dsi_stop() and mtk_dsi_start() is asymmetric, since
> +	 * mtk_dsi_stop() should be called after
> mtk_drm_crtc_atomic_disable(),
> +	 * which needs irq for vblank, and mtk_dsi_stop() will disable
> irq.
> +	 * mtk_dsi_start() needs to be called in
> mtk_output_dsi_enable(),
> +	 * after dsi is fully set.
> +	 */
> +	mtk_dsi_stop(dsi);
> +
> +	mtk_dsi_switch_to_cmd_mode(dsi, VM_DONE_INT_FLAG, 500);
>  
>  	dsi->enabled = false;
>  }
> @@ -765,10 +756,26 @@ static void mtk_dsi_bridge_enable(struct
> drm_bridge *bridge)
>  	mtk_output_dsi_enable(dsi);
>  }
>  
> +static void mtk_dsi_bridge_pre_enable(struct drm_bridge *bridge)
> +{
> +	struct mtk_dsi *dsi = bridge_to_dsi(bridge);
> +
> +	mtk_dsi_poweron(dsi);
> +}
> +
> +static void mtk_dsi_bridge_post_disable(struct drm_bridge *bridge)
> +{
> +	struct mtk_dsi *dsi = bridge_to_dsi(bridge);
> +
> +	mtk_dsi_poweroff(dsi);
> +}
> +
>  static const struct drm_bridge_funcs mtk_dsi_bridge_funcs = {
>  	.attach = mtk_dsi_bridge_attach,
>  	.disable = mtk_dsi_bridge_disable,
>  	.enable = mtk_dsi_bridge_enable,
> +	.pre_enable = mtk_dsi_bridge_pre_enable,
> +	.post_disable = mtk_dsi_bridge_post_disable,
>  	.mode_set = mtk_dsi_bridge_mode_set,
>  };
>  

[3/3] drm/mediatek: keep dsi as LP00 before dcs cmds transfer

[xinlei.lee]

From: Jitao Shi <jitao.shi@mediatek.com>

To comply with the panel sequence, hold the mipi signal to LP00 before the dcs cmds transmission, 
and pull the mipi signal high from LP00 to LP11 until the start of the dcs cmds transmission.
If dsi is not in cmd mode, then dsi will pull the mipi signal high in the mtk_output_dsi_enable function.

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dsi.c | 32 +++++++++++++++++++++++++-------
 1 file changed, 25 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c
index e47c338..17a5270 100644
--- a/drivers/gpu/drm/mediatek/mtk_dsi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
@@ -203,6 +203,7 @@ struct mtk_dsi {
 	struct mtk_phy_timing phy_timing;
 	int refcount;
 	bool enabled;
+	bool lanes_ready;
 	u32 irq_data;
 	wait_queue_head_t irq_wait_queue;
 	const struct mtk_dsi_driver_data *driver_data;
@@ -654,13 +655,6 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
 	mtk_dsi_config_vdo_timing(dsi);
 	mtk_dsi_set_interrupt_enable(dsi);
 
-	mtk_dsi_rxtx_control(dsi);
-	usleep_range(30, 100);
-	mtk_dsi_reset_dphy(dsi);
-	mtk_dsi_clk_ulp_mode_leave(dsi);
-	mtk_dsi_lane0_ulp_mode_leave(dsi);
-	mtk_dsi_clk_hs_mode(dsi, 0);
-
 	return 0;
 err_disable_engine_clk:
 	clk_disable_unprepare(dsi->engine_clk);
@@ -682,6 +676,8 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
 	mtk_dsi_reset_engine(dsi);
 	mtk_dsi_lane0_ulp_mode_enter(dsi);
 	mtk_dsi_clk_ulp_mode_enter(dsi);
+	/* set the lane number as 0 */
+	writel(0, dsi->regs + DSI_TXRX_CTRL);
 
 	mtk_dsi_disable(dsi);
 
@@ -689,6 +685,8 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
 	clk_disable_unprepare(dsi->digital_clk);
 
 	phy_power_off(dsi->phy);
+
+	dsi->lanes_ready = false;
 }
 
 static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
@@ -696,6 +694,16 @@ static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
 	if (dsi->enabled)
 		return;
 
+	if (!dsi->lanes_ready) {
+		dsi->lanes_ready = true;
+		mtk_dsi_rxtx_control(dsi);
+		usleep_range(30, 100);
+		mtk_dsi_reset_dphy(dsi);
+		mtk_dsi_clk_ulp_mode_leave(dsi);
+		mtk_dsi_lane0_ulp_mode_leave(dsi);
+		mtk_dsi_clk_hs_mode(dsi, 0);
+	}
+
 	mtk_dsi_set_mode(dsi);
 	mtk_dsi_clk_hs_mode(dsi, 1);
 
@@ -907,6 +915,16 @@ static ssize_t mtk_dsi_host_transfer(struct mipi_dsi_host *host,
 	if (MTK_DSI_HOST_IS_READ(msg->type))
 		irq_flag |= LPRX_RD_RDY_INT_FLAG;
 
+	if (!dsi->lanes_ready) {
+		dsi->lanes_ready = true;
+		mtk_dsi_rxtx_control(dsi);
+		usleep_range(30, 100);
+		mtk_dsi_reset_dphy(dsi);
+		mtk_dsi_clk_ulp_mode_leave(dsi);
+		mtk_dsi_lane0_ulp_mode_leave(dsi);
+		mtk_dsi_clk_hs_mode(dsi, 0);
+		msleep(20);
+	}
 	if (mtk_dsi_host_send_cmd(dsi, msg, irq_flag) < 0)
 		return -ETIME;
 
-- 
2.6.4

Re: [3/3] drm/mediatek: keep dsi as LP00 before dcs cmds transfer

[CK Hu]

Hi, Xinlei:

On Fri, 2022-02-11 at 22:30 +0800, xinlei.lee@mediatek.com wrote:
> From: Jitao Shi <jitao.shi@mediatek.com>
> 
> To comply with the panel sequence, hold the mipi signal to LP00
> before the dcs cmds transmission, 
> and pull the mipi signal high from LP00 to LP11 until the start of
> the dcs cmds transmission.
> If dsi is not in cmd mode, then dsi will pull the mipi signal high in
> the mtk_output_dsi_enable function.
> 
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dsi.c | 32 +++++++++++++++++++++++++---
> ----
>  1 file changed, 25 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c
> b/drivers/gpu/drm/mediatek/mtk_dsi.c
> index e47c338..17a5270 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dsi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
> @@ -203,6 +203,7 @@ struct mtk_dsi {
>  	struct mtk_phy_timing phy_timing;
>  	int refcount;
>  	bool enabled;
> +	bool lanes_ready;
>  	u32 irq_data;
>  	wait_queue_head_t irq_wait_queue;
>  	const struct mtk_dsi_driver_data *driver_data;
> @@ -654,13 +655,6 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
>  	mtk_dsi_config_vdo_timing(dsi);
>  	mtk_dsi_set_interrupt_enable(dsi);
>  
> -	mtk_dsi_rxtx_control(dsi);
> -	usleep_range(30, 100);
> -	mtk_dsi_reset_dphy(dsi);
> -	mtk_dsi_clk_ulp_mode_leave(dsi);
> -	mtk_dsi_lane0_ulp_mode_leave(dsi);
> -	mtk_dsi_clk_hs_mode(dsi, 0);
> -
>  	return 0;
>  err_disable_engine_clk:
>  	clk_disable_unprepare(dsi->engine_clk);
> @@ -682,6 +676,8 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
>  	mtk_dsi_reset_engine(dsi);
>  	mtk_dsi_lane0_ulp_mode_enter(dsi);
>  	mtk_dsi_clk_ulp_mode_enter(dsi);
> +	/* set the lane number as 0 */
> +	writel(0, dsi->regs + DSI_TXRX_CTRL);

If this is not related to 'sequence', separate this to another patch.

Regards,
CK

>  
>  	mtk_dsi_disable(dsi);
>  
> @@ -689,6 +685,8 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
>  	clk_disable_unprepare(dsi->digital_clk);
>  
>  	phy_power_off(dsi->phy);
> +
> +	dsi->lanes_ready = false;
>  }
>  
>  static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
> @@ -696,6 +694,16 @@ static void mtk_output_dsi_enable(struct mtk_dsi
> *dsi)
>  	if (dsi->enabled)
>  		return;
>  
> +	if (!dsi->lanes_ready) {
> +		dsi->lanes_ready = true;
> +		mtk_dsi_rxtx_control(dsi);
> +		usleep_range(30, 100);
> +		mtk_dsi_reset_dphy(dsi);
> +		mtk_dsi_clk_ulp_mode_leave(dsi);
> +		mtk_dsi_lane0_ulp_mode_leave(dsi);
> +		mtk_dsi_clk_hs_mode(dsi, 0);
> +	}
> +
>  	mtk_dsi_set_mode(dsi);
>  	mtk_dsi_clk_hs_mode(dsi, 1);
>  
> @@ -907,6 +915,16 @@ static ssize_t mtk_dsi_host_transfer(struct
> mipi_dsi_host *host,
>  	if (MTK_DSI_HOST_IS_READ(msg->type))
>  		irq_flag |= LPRX_RD_RDY_INT_FLAG;
>  
> +	if (!dsi->lanes_ready) {
> +		dsi->lanes_ready = true;
> +		mtk_dsi_rxtx_control(dsi);
> +		usleep_range(30, 100);
> +		mtk_dsi_reset_dphy(dsi);
> +		mtk_dsi_clk_ulp_mode_leave(dsi);
> +		mtk_dsi_lane0_ulp_mode_leave(dsi);
> +		mtk_dsi_clk_hs_mode(dsi, 0);
> +		msleep(20);
> +	}
>  	if (mtk_dsi_host_send_cmd(dsi, msg, irq_flag) < 0)
>  		return -ETIME;
>  

Re: [0/3] Cooperate with DSI RX devices to modify dsi funcs and delay mipi high to cooperate with panel sequence

[CK Hu]

Hi, Xinlei:

On Fri, 2022-02-11 at 22:30 +0800, xinlei.lee@mediatek.com wrote:
> From: xinlei lee <xinlei.lee@mediatek.com>
> 
> In order to match the changes of DSI RX devices (for example,
> anx7625), 
> the poweron/poweroff of dsi is extracted from enable/disable and 
> defined as new funcs (pre_enable/post_disable).
> 
> The delayed MIPI signal is pulled high from LP00 to LP11, 
> in order to match the power-on sequence of the panel.

This is series a bug-fix or new feature (If anx7625 has never work in
upstream and this series would make support anx7625, this is new
feature) If this is a bug-fix, add Fixes tag [1] in patches.

[1] 
https://www.kernel.org/doc/html/v5.16/process/submitting-patches.html

Regards,
CK

> 
> Jitao Shi (3):
>   drm/mediatek: dsi fine tune the dsi poweron flow
>   drm/mediatek: dsi bridge implement pre_enable and post_disable
>   drm/mediatek: keep dsi as LP00 before dcs cmds transfer
> 
>  drivers/gpu/drm/mediatek/mtk_dsi.c | 73 +++++++++++++++++++++++++---
> ----------
>  1 file changed, 49 insertions(+), 24 deletions(-)
>