[PATCH 0/6] arm64: dts: qcom: talos-lyra-evk: Add display overlays for EVK board

[PATCH 0/6] arm64: dts: qcom: talos-lyra-evk: Add display overlays for EVK board

[anand.tiwari]

Talos Lyra EVK SoC card are mounted on the Lyra carrier card. The
DSI0 interface from SoC card is routed to either the 22-pin DSI
connector on carrier card named as JDISP1 DSI0 or to the DSI0_B2B
connector, through a MUX which can be selected by a hardware DIP
switch. There are multiple daughter cards designed that can be
connected to this B2B connector.

The below B2B display interfaces are enabled by default in base DTB:
  - DSI-to-HDMI using the LT9611UXD daughter card

Below overlay DTs are added for additional display configurations:
  - talos-lyra-evk-dlc0697: DLC0697 DSI panel for Lyra with DLC
    daughter card
  - talos-lyra-evk-raspberrypi-dsi-7inch: Raspberry Pi 7-inch DSI
    panel with touch via the 22-pin DSI connector for Lyra
  - talos-lyra-evk-waveshare-dsi-8inch: Waveshare 8-inch DSI panel
    with touch via the 22-pin DSI connector for Lyra
  - talos-lyra-evk-lvds-auo,g133han01: AUO G133HAN01 LVDS panel for
    Lyra with LVDS daughter card

These overlays are applied on top of the corresponding base board
DTBs.

Link: https://lore.kernel.org/r/20261012-talos-lyra-evk-v2-v2-0-dcc9316ebb59@oss.qualcomm.com
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
---
Anand Tiwari (2):
      arm64: defconfig: Enable PWM_CLK for backlight PWM support
      arm64: dts: qcom: talos-lyra-evk: Add AUO G133HAN01 LVDS panel overlay

Mohit Dsor (1):
      arm64: dts: qcom: talos-lyra-evk: Add LT9611UXD HDMI bridge support

Shashank Maurya (3):
      arm64: dts: qcom: talos-lyra-evk: Add DLC DLC0697 panel overlay
      arm64: dts: qcom: talos-lyra-evk: Add RPi 7-inch DSI panel overlay
      arm64: dts: qcom: talos-lyra-evk: Add Waveshare 8-inch DSI panel overlay

 arch/arm64/boot/dts/qcom/Makefile                  |  18 +++
 .../boot/dts/qcom/talos-lyra-evk-dlc0697.dtso      |  78 ++++++++++++
 .../qcom/talos-lyra-evk-lvds-auo,g133han01.dtso    | 134 +++++++++++++++++++++
 .../qcom/talos-lyra-evk-raspberrypi-dsi-7inch.dtso |  88 ++++++++++++++
 .../qcom/talos-lyra-evk-waveshare-dsi-8inch.dtso   |  75 ++++++++++++
 arch/arm64/boot/dts/qcom/talos-lyra-evk.dts        | 106 ++++++++++++++++
 arch/arm64/configs/defconfig                       |   1 +
 7 files changed, 500 insertions(+)
---
base-commit: 1128acbf0e37fb5fe5b67d7e2494fa45905afda0
change-id: 20261019-lyra-display-upstream-post-24656268a902

Best regards,
--  
Anand Tiwari <anand.tiwari@oss.qualcomm.com>

[PATCH 1/6] arm64: dts: qcom: talos-lyra-evk: Add LT9611UXD HDMI bridge support

[anand.tiwari]

From: Mohit Dsor <mohit.dsor@oss.qualcomm.com>

Add support for the Lontium LT9611UXD DSI-to-HDMI bridge, enabled by
default on the Talos Lyra EVK base board DT, to provide HDMI output
on the DSI0_B2B connector on the carrier card.

LT9611UXD is connected through I2C2, with reset and interrupt
connected to TLMM GPIO61 and GPIO60 respectively.

Signed-off-by: Mohit Dsor <mohit.dsor@oss.qualcomm.com>
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/talos-lyra-evk.dts | 105 ++++++++++++++++++++++++++++
 1 file changed, 105 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
index cfb563658fe0..ec5c10a40521 100644
--- a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
@@ -4,6 +4,8 @@
  */
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include "talos-lyra-evk-som.dtsi"
 
 / {
@@ -11,6 +13,10 @@ / {
 	compatible = "qcom,talos-lyra-evk", "qcom,qcs615", "qcom,sm6150";
 	chassis-type = "embedded";
 
+	aliases {
+		i2c2 = &i2c2;
+	};
+
 	dp0-connector {
 		compatible = "dp-connector";
 		label = "DP0";
@@ -25,6 +31,65 @@ dp0_connector_in: endpoint {
 		};
 	};
 
+	hdmi_connector: hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_out: endpoint {
+			remote-endpoint = <&hdmi_bridge_out>;
+			};
+		};
+	};
+
+	vreg_disp_3p3: regulator-disp-3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_disp_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-0 = <&lcd_bias_en>;
+		pinctrl-names = "default";
+	};
+
+};
+
+&i2c2 {
+	status = "okay";
+
+	hdmi_bridge: hdmi-bridge@41 {
+		compatible = "lontium,lt9611uxd";
+		reg = <0x41>;
+		interrupts-extended = <&tlmm 60 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&vreg_disp_3p3>;
+		vdd-supply = <&vreg_s4a>;
+
+		pinctrl-0 = <&bridge_irq_pin &bridge_rst_pin>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				hdmi_bridge_in: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				hdmi_bridge_out: endpoint {
+					remote-endpoint = <&hdmi_connector_out>;
+				};
+			};
+		};
+	};
 };
 
 &i2c5 {
@@ -74,6 +139,23 @@ &mdss_dp0_out {
 	remote-endpoint = <&dp0_connector_in>;
 };
 
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&hdmi_bridge_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l11a>;
+
+	status = "okay";
+};
+
 &pon_pwrkey {
 	status = "okay";
 };
@@ -135,3 +217,26 @@ &usb_qmpphy_2 {
 
 	status = "okay";
 };
+
+&tlmm {
+	lcd_bias_en: lcd-bias-en-state {
+		pins = "gpio3";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bridge_irq_pin: bridge-irq-state {
+		pins = "gpio60";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	bridge_rst_pin: bridge-rst-state {
+		pins = "gpio61";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+};

-- 
2.55.0

[PATCH 2/6] arm64: dts: qcom: talos-lyra-evk: Add DLC DLC0697 panel overlay

[anand.tiwari]

From: Shashank Maurya <shashank.maurya@oss.qualcomm.com>

Add a DT overlay for Talos Lyra EVK, to enable DLC0697 panel when
DLC daughter card connected to DSI0_B2B on carrier card.

Configure DLC0697 reset GPIO, supplies, pinctrl states and GPIO
backlight controlled through TLMM GPIO 2.

Disable the default HDMI bridge and connector in favour of the DSI
panel.

Signed-off-by: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  4 ++
 .../boot/dts/qcom/talos-lyra-evk-dlc0697.dtso      | 78 ++++++++++++++++++++++
 2 files changed, 82 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 4f8ca3112fed..5248b6be68f5 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -476,6 +476,10 @@ dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk-lvds-auo,g133han01.dtb
 talos-evk-rpi-display-2-5in-dtbs	:= \
 	talos-evk.dtb talos-evk-rpi-display-2-5in.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk-rpi-display-2-5in.dtb
+
+talos-lyra-evk-dlc0697-dtbs := talos-lyra-evk.dtb talos-lyra-evk-dlc0697.dtbo
+dtb-$(CONFIG_ARCH_QCOM)     += talos-lyra-evk-dlc0697.dtb
+dtb-$(CONFIG_ARCH_QCOM)     += talos-lyra-evk-dlc0697.dtbo
 x1e001de-devkit-el2-dtbs	:= x1e001de-devkit.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e001de-devkit.dtb x1e001de-devkit-el2.dtb
 x1e78100-lenovo-thinkpad-t14s-el2-dtbs	:= x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk-dlc0697.dtso b/arch/arm64/boot/dts/qcom/talos-lyra-evk-dlc0697.dtso
new file mode 100644
index 000000000000..e50bf69c7b37
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk-dlc0697.dtso
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&mdss_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "dlc,dlc0697", "ilitek,ili7807s";
+		reg = <0>;
+
+		reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>;
+		backlight = <&backlight>;
+
+		vddi-supply = <&vreg_s4a>;
+		avdd-supply = <&vreg_disp_3p3>;
+		avee-supply = <&vreg_disp_3p3>;
+
+		pinctrl-0 = <&panel_rst_n &panel_te_pin>;
+		pinctrl-1 = <&panel_rst_n_suspend>;
+		pinctrl-names = "default", "sleep";
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+};
+
+&tlmm {
+	panel_te_pin: panel-te-pin-state {
+		pins = "gpio98";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	panel_rst_n: panel-rst-n-state {
+		pins = "gpio118";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	panel_rst_n_suspend: panel-rst-n-suspend-state {
+		pins = "gpio118";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};

-- 
2.55.0

[PATCH 3/6] arm64: dts: qcom: talos-lyra-evk: Add RPi 7-inch DSI panel overlay

[anand.tiwari]

From: Shashank Maurya <shashank.maurya@oss.qualcomm.com>

Add a DT overlay to enable Raspberry Pi 7-inch DSI panel connected
to DSI 22pin on the carrier card.

DSI0 from SOC is routed through MUX which can be selected by DIP
switch S1016.5 ON for enabling this 22pin connector.

Add the regulator and backlight controller at I2C2 address 0x45,
Goodix GT911 touch controller, panel power and reset control, and
a 2-lane DSI connection.

Disable the default HDMI bridge and connector in favour of the RPi
DSI panel.

Signed-off-by: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  5 ++
 .../qcom/talos-lyra-evk-raspberrypi-dsi-7inch.dtso | 88 ++++++++++++++++++++++
 2 files changed, 93 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 5248b6be68f5..a2a2ffbbce3a 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -480,6 +480,11 @@ dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk-rpi-display-2-5in.dtb
 talos-lyra-evk-dlc0697-dtbs := talos-lyra-evk.dtb talos-lyra-evk-dlc0697.dtbo
 dtb-$(CONFIG_ARCH_QCOM)     += talos-lyra-evk-dlc0697.dtb
 dtb-$(CONFIG_ARCH_QCOM)     += talos-lyra-evk-dlc0697.dtbo
+
+talos-lyra-evk-raspberrypi-dsi-7inch-dtbs := \
+        talos-lyra-evk.dtb talos-lyra-evk-raspberrypi-dsi-7inch.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-raspberrypi-dsi-7inch.dtb
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-raspberrypi-dsi-7inch.dtbo
 x1e001de-devkit-el2-dtbs	:= x1e001de-devkit.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e001de-devkit.dtb x1e001de-devkit-el2.dtb
 x1e78100-lenovo-thinkpad-t14s-el2-dtbs	:= x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk-raspberrypi-dsi-7inch.dtso b/arch/arm64/boot/dts/qcom/talos-lyra-evk-raspberrypi-dsi-7inch.dtso
new file mode 100644
index 000000000000..cee602a78322
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk-raspberrypi-dsi-7inch.dtso
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	display_bl: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&reg_display>;
+		pwms = <&mcu 0 255 0>;
+	};
+
+	reg_display: regulator-display {
+		compatible = "regulator-fixed";
+		regulator-name = "rpi-display";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_dsi_touch: regulator-dsi-touch {
+		compatible = "regulator-fixed";
+		gpio = <&mcu 1 GPIO_ACTIVE_HIGH>;
+		regulator-name = "rpi-touch";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <50000>;
+		enable-active-high;
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	mcu: gpio@45 {
+		compatible = "raspberrypi,touchscreen-panel-regulator-v2";
+		reg = <0x45>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#pwm-cells = <3>;
+	};
+
+	touchscreen@5d {
+		compatible = "goodix,gt911";
+		reg = <0x5d>;
+		AVDD28-supply = <&reg_dsi_touch>;
+		touchscreen-size-x = <720>;
+		touchscreen-size-y = <1280>;
+	};
+};
+
+&mdss_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "raspberrypi,dsi-7inch";
+		reg = <0>;
+
+		reset-gpios = <&mcu 0 GPIO_ACTIVE_LOW>;
+		power-supply = <&reg_display>;
+		iovcc-supply = <&vreg_s4a>;
+		backlight = <&display_bl>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1>;
+};

-- 
2.55.0

[PATCH 4/6] arm64: dts: qcom: talos-lyra-evk: Add Waveshare 8-inch DSI panel overlay

[anand.tiwari]

From: Shashank Maurya <shashank.maurya@oss.qualcomm.com>

Add a DT overlay to enable Waveshare 8-inch DSI panel connected to
DSI 22pin on the carrier card.

DSI0 from SOC is routed through MUX which can be selected by DIP
switch S1016.5 ON, for enabling this 22pin connector.

Add the JD9365DA-H3 panel, GPIO expander at I2C2 address 0x45 for
panel power, reset and backlight, and the Goodix GT9271 touch
controller.

Disable the default HDMI bridge and connector in favour of the
Waveshare DSI panel.

Signed-off-by: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  5 ++
 .../qcom/talos-lyra-evk-waveshare-dsi-8inch.dtso   | 75 ++++++++++++++++++++++
 2 files changed, 80 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index a2a2ffbbce3a..614152913cbb 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -485,6 +485,11 @@ talos-lyra-evk-raspberrypi-dsi-7inch-dtbs := \
         talos-lyra-evk.dtb talos-lyra-evk-raspberrypi-dsi-7inch.dtbo
 dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-raspberrypi-dsi-7inch.dtb
 dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-raspberrypi-dsi-7inch.dtbo
+
+talos-lyra-evk-waveshare-dsi-8inch-dtbs := \
+        talos-lyra-evk.dtb talos-lyra-evk-waveshare-dsi-8inch.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-waveshare-dsi-8inch.dtb
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-waveshare-dsi-8inch.dtbo
 x1e001de-devkit-el2-dtbs	:= x1e001de-devkit.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e001de-devkit.dtb x1e001de-devkit-el2.dtb
 x1e78100-lenovo-thinkpad-t14s-el2-dtbs	:= x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk-waveshare-dsi-8inch.dtso b/arch/arm64/boot/dts/qcom/talos-lyra-evk-waveshare-dsi-8inch.dtso
new file mode 100644
index 000000000000..e9a8fdf0c179
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk-waveshare-dsi-8inch.dtso
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	panel_avdd: regulator-panel-avdd {
+		compatible = "regulator-fixed";
+		regulator-name = "panel-avdd";
+		gpios = <&wsgpio 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	panel_iovcc: regulator-panel-iovcc {
+		compatible = "regulator-fixed";
+		regulator-name = "panel-iovcc";
+		gpios = <&wsgpio 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wsgpio: gpio@45 {
+		compatible = "waveshare,dsi-touch-gpio";
+		reg = <0x45>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	touchscreen@5d {
+		compatible = "goodix,gt9271";
+		reg = <0x5d>;
+		reset-gpios = <&wsgpio 9 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mdss_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "waveshare,8.0-dsi-touch-a", "jadard,jd9365da-h3";
+		reg = <0>;
+
+		reset-gpios = <&wsgpio 1 GPIO_ACTIVE_LOW>;
+		vccio-supply = <&panel_iovcc>;
+		vdd-supply = <&panel_avdd>;
+		backlight = <&wsgpio>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+};

-- 
2.55.0

[PATCH 5/6] arm64: defconfig: Enable PWM_CLK for backlight PWM support

[Anand Tiwari]

Enable CONFIG_PWM_CLK so the generic clock-based PWM driver is
available, used by the Talos Lyra EVK LVDS panel overlay backlight.

Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 50d6357727af..365a69470d13 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -1620,6 +1620,7 @@ CONFIG_PWM_ADP5585=m
 CONFIG_PWM_APPLE=m
 CONFIG_PWM_BCM2835=m
 CONFIG_PWM_BRCMSTB=m
+CONFIG_PWM_CLK=m
 CONFIG_PWM_CROS_EC=m
 CONFIG_PWM_IMX27=m
 CONFIG_PWM_MEDIATEK=m

-- 
2.55.0

[PATCH 6/6] arm64: dts: qcom: talos-lyra-evk: Add AUO G133HAN01 LVDS panel overlay

[Anand Tiwari]

Add a DT overlay for Talos Lyra EVK, to enable LVDS interface when
LVDS daughter card is connected to DSI0_B2B on carrier card.

There is SN65DSI84 DSI-to-LVDS bridge on the daughter card which is
connected through I2C5 with reset and interrupt connected to
GPIO61 and GPIO60. Backlight is driven by a generic clock-based PWM
using GCC_GP3 on TLMM GPIO59, with an additional backlight enable
GPIO on TLMM GPIO2.

Disable the default HDMI bridge and connector in favour of the LVDS
panel.

Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |   4 +
 .../qcom/talos-lyra-evk-lvds-auo,g133han01.dtso    | 134 +++++++++++++++++++++
 arch/arm64/boot/dts/qcom/talos-lyra-evk.dts        |   1 +
 3 files changed, 139 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 614152913cbb..f0551bd2d8e2 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -473,6 +473,10 @@ dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk-camera-imx577.dtb
 talos-evk-lvds-auo,g133han01-dtbs	:= \
 	talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk-lvds-auo,g133han01.dtb
+talos-lyra-evk-lvds-auo,g133han01-dtbs := \
+	talos-lyra-evk.dtb talos-lyra-evk-lvds-auo,g133han01.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-lvds-auo,g133han01.dtb
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-lvds-auo,g133han01.dtbo
 talos-evk-rpi-display-2-5in-dtbs	:= \
 	talos-evk.dtb talos-evk-rpi-display-2-5in.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk-rpi-display-2-5in.dtb
diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk-lvds-auo,g133han01.dtso b/arch/arm64/boot/dts/qcom/talos-lyra-evk-lvds-auo,g133han01.dtso
new file mode 100644
index 000000000000..3edb56937446
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk-lvds-auo,g133han01.dtso
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,qcs615-gcc.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&{/} {
+	bklt_pwm: pwm {
+		compatible = "clk-pwm";
+		#pwm-cells = <2>;
+		assigned-clock-parents = <&rpmhcc RPMH_CXO_CLK>;
+		assigned-clocks = <&gcc GCC_GP3_CLK_SRC>;
+		clocks = <&gcc GCC_GP3_CLK>;
+		pinctrl-0 = <&bklt_pwm_default>;
+		pinctrl-names = "default";
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&bklt_pwm 0 100000>;
+		power-supply = <&vreg_disp_3p3>;
+		enable-gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <128>;
+	};
+
+	panel-lvds {
+		compatible = "auo,g133han01";
+		power-supply = <&vreg_disp_3p3>;
+		backlight = <&backlight>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* LVDS Channel A — odd pixels */
+			port@0 {
+				reg = <0>;
+				dual-lvds-odd-pixels;
+
+				lvds_panel_out_a: endpoint {
+					remote-endpoint = <&sn65dsi84_out_a>;
+				};
+			};
+
+			/* LVDS Channel B — even pixels */
+			port@1 {
+				reg = <1>;
+				dual-lvds-even-pixels;
+
+				lvds_panel_out_b: endpoint {
+					remote-endpoint = <&sn65dsi84_out_b>;
+				};
+			};
+		};
+	};
+
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&i2c5 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&tlmm 61 GPIO_ACTIVE_HIGH>;
+		interrupts-extended = <&tlmm 60 IRQ_TYPE_EDGE_FALLING>;
+		vcc-supply = <&vreg_s4a>;
+
+		pinctrl-0 = <&bridge_irq_pin &bridge_rst_pin>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sn65dsi84_in: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+					data-lanes = <1 2 3 4>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				sn65dsi84_out_a: endpoint {
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&lvds_panel_out_a>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+
+				sn65dsi84_out_b: endpoint {
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&lvds_panel_out_b>;
+				};
+			};
+		};
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&tlmm {
+	bklt_pwm_default: bklt-pwm-default-state {
+		pins = "gpio59";
+		function = "gcc_gp";
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&sn65dsi84_in>;
+	data-lanes = <0 1 2 3>;
+};
diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
index ec5c10a40521..20967c294543 100644
--- a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
@@ -15,6 +15,7 @@ / {
 
 	aliases {
 		i2c2 = &i2c2;
+		i2c5 = &i2c5;
 	};
 
 	dp0-connector {

-- 
2.55.0

Re: [PATCH 1/6] arm64: dts: qcom: talos-lyra-evk: Add LT9611UXD HDMI bridge support

[Konrad Dybcio]

On 10/21/26 5:17 PM, anand.tiwari@oss.qualcomm.com wrote:
> From: Mohit Dsor <mohit.dsor@oss.qualcomm.com>
> 
> Add support for the Lontium LT9611UXD DSI-to-HDMI bridge, enabled by
> default on the Talos Lyra EVK base board DT, to provide HDMI output
> on the DSI0_B2B connector on the carrier card.

[...]

> +	vreg_disp_3p3: regulator-disp-3p3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vreg_disp_3p3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&tlmm 3 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		pinctrl-0 = <&lcd_bias_en>;
> +		pinctrl-names = "default";
> +	};
> +
> +};

Stray \n above

Otherwise looks good

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH 2/6] arm64: dts: qcom: talos-lyra-evk: Add DLC DLC0697 panel overlay

[Konrad Dybcio]

On 10/21/26 5:17 PM, anand.tiwari@oss.qualcomm.com wrote:
> From: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
> 
> Add a DT overlay for Talos Lyra EVK, to enable DLC0697 panel when
> DLC daughter card connected to DSI0_B2B on carrier card.

[...]

> +&{/} {
> +	backlight: backlight {
> +		compatible = "gpio-backlight";
> +		gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
> +		default-on;

This is a little strange, doesn't it come on as the panel unblanks?

Otherwise

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH 3/6] arm64: dts: qcom: talos-lyra-evk: Add RPi 7-inch DSI panel overlay

[Konrad Dybcio]

On 10/21/26 5:17 PM, anand.tiwari@oss.qualcomm.com wrote:
> From: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
> 
> Add a DT overlay to enable Raspberry Pi 7-inch DSI panel connected
> to DSI 22pin on the carrier card.
> 
> DSI0 from SOC is routed through MUX which can be selected by DIP
> switch S1016.5 ON for enabling this 22pin connector.
> 
> Add the regulator and backlight controller at I2C2 address 0x45,
> Goodix GT911 touch controller, panel power and reset control, and
> a 2-lane DSI connection.
> 
> Disable the default HDMI bridge and connector in favour of the RPi
> DSI panel.
> 
> Signed-off-by: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
> Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH 4/6] arm64: dts: qcom: talos-lyra-evk: Add Waveshare 8-inch DSI panel overlay

[Konrad Dybcio]

On 10/21/26 5:17 PM, anand.tiwari@oss.qualcomm.com wrote:
> From: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
> 
> Add a DT overlay to enable Waveshare 8-inch DSI panel connected to
> DSI 22pin on the carrier card.
> 
> DSI0 from SOC is routed through MUX which can be selected by DIP
> switch S1016.5 ON, for enabling this 22pin connector.
> 
> Add the JD9365DA-H3 panel, GPIO expander at I2C2 address 0x45 for
> panel power, reset and backlight, and the Goodix GT9271 touch
> controller.
> 
> Disable the default HDMI bridge and connector in favour of the
> Waveshare DSI panel.
> 
> Signed-off-by: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
> Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH 6/6] arm64: dts: qcom: talos-lyra-evk: Add AUO G133HAN01 LVDS panel overlay

[Konrad Dybcio]

On 10/21/26 5:17 PM, Anand Tiwari wrote:
> Add a DT overlay for Talos Lyra EVK, to enable LVDS interface when
> LVDS daughter card is connected to DSI0_B2B on carrier card.
> 
> There is SN65DSI84 DSI-to-LVDS bridge on the daughter card which is
> connected through I2C5 with reset and interrupt connected to
> GPIO61 and GPIO60. Backlight is driven by a generic clock-based PWM
> using GCC_GP3 on TLMM GPIO59, with an additional backlight enable
> GPIO on TLMM GPIO2.
> 
> Disable the default HDMI bridge and connector in favour of the LVDS
> panel.
> 
> Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad