mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Frank Li <Frank.li@nxp.com>
To: Claudiu Beznea <claudiu.beznea@kernel.org>
Cc: wsa+renesas@sang-engineering.com,
	tommaso.merciai.xr@bp.renesas.com, alexandre.belloni@bootlin.com,
	p.zabel@pengutronix.de, claudiu.beznea@tuxon.dev,
	linux-i3c@lists.infradead.org, linux-kernel@vger.kernel.org,
	linux-renesas-soc@vger.kernel.org,
	Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>,
	stable@vger.kernel.org
Subject: Re: [PATCH 03/17] i3c: renesas: Restore STDBR and EXTBR registers on resume
Date: Thu, 28 May 2026 15:13:25 -0400	[thread overview]
Message-ID: <ahiT1YkbWNz9y4mH@lizhi-Precision-Tower-5810> (raw)
In-Reply-To: <560f3365-8a22-477b-ae3d-61e8f4103e83@kernel.org>

On Thu, May 28, 2026 at 11:29:46AM +0300, Claudiu Beznea wrote:
> Hi, Frank,
>
> On 5/22/26 22:10, Frank Li wrote:
> > On Fri, May 22, 2026 at 01:18:01PM +0300, Claudiu Beznea wrote:
> > > From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
> > >
> > > The Renesas RZ/G3S supports a power saving state where power to the most
> > > SoC componentes (including I3C) is lost.
> > >
> > > The STDBR and EXTBR are configured in initialization phase though the
> > > struct i3c_master_controller_ops::bus_init. Set them on resume function
> > > as well to keep the same state of the controller after a suspend with
> > > power loss and a similar initialization sequence as in bus_init.
> > >
> > > Fixes: e7218986319b ("i3c: renesas: Add suspend/resume support")
> > > Cc: stable@vger.kernel.org
> > > Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
> > > ---
> > >   drivers/i3c/master/renesas-i3c.c | 10 ++++++----
> > >   1 file changed, 6 insertions(+), 4 deletions(-)
> > >
> > > diff --git a/drivers/i3c/master/renesas-i3c.c b/drivers/i3c/master/renesas-i3c.c
> > > index 1917549cf6d5..6c23f956ad2a 100644
> > > --- a/drivers/i3c/master/renesas-i3c.c
> > > +++ b/drivers/i3c/master/renesas-i3c.c
> > > @@ -260,6 +260,7 @@ struct renesas_i3c {
> > >   	u32 dyn_addr;
> > >   	u32 i2c_STDBR;
> > >   	u32 i3c_STDBR;
> > > +	u32 extbr;
> >
> > can you keep consisent with above 2 register, use upcase EXTBR,
>
> Using upper case for this will mislead the compiler. There is already a
> macro defined for EXTBR:

That's fine.

Reviewed-by: Frank Li <Frank.Li@nxp.com>

>
> #define EXTBR                   0x78
>
> Defining this member as:
>
> u32 EXTBR;
>
> will make the compiler try to replace the EXTBR in "i3c->EXTBR" at
> preprocessing time:
>
>   CC [M]  drivers/i3c/master/renesas-i3c.o
> ../drivers/i3c/master/renesas-i3c.c:65:17: error: expected identifier or ‘(’
> before numeric constant
>    65 | #define EXTBR   0x78
>       |                 ^~~~
> ../drivers/i3c/master/renesas-i3c.c:263:6: note: in expansion of macro ‘EXTBR’
>   263 |  u32 EXTBR;
>       |      ^~~~~
> ../drivers/i3c/master/renesas-i3c.c: In function ‘renesas_i3c_bus_init’:
> ../drivers/i3c/master/renesas-i3c.c:65:17: error: expected identifier before
> numeric constant
>    65 | #define EXTBR   0x78
>       |                 ^~~~
> ../drivers/i3c/master/renesas-i3c.c:611:7: note: in expansion of macro ‘EXTBR’
>   611 |  i3c->EXTBR = EXTBR_EBRLO(od_low_ticks) | EXTBR_EBRHO(od_high_ticks) |
>       |       ^~~~~
> ../drivers/i3c/master/renesas-i3c.c:65:17: error: expected identifier before
> numeric constant
>    65 | #define EXTBR   0x78
>       |                 ^~~~
> ../drivers/i3c/master/renesas-i3c.c:613:40: note: in expansion of macro ‘EXTBR’
>   613 |  renesas_writel(i3c->regs, EXTBR, i3c->EXTBR);
>       |                                        ^~~~~
> ../drivers/i3c/master/renesas-i3c.c: In function ‘renesas_i3c_resume_noirq’:
> ../drivers/i3c/master/renesas-i3c.c:65:17: error: expected identifier before
> numeric constant
>    65 | #define EXTBR   0x78
>       |                 ^~~~
> ../drivers/i3c/master/renesas-i3c.c:1451:40: note: in expansion of macro ‘EXTBR’
>  1451 |  renesas_writel(i3c->regs, EXTBR, i3c->EXTBR);
>       |                                        ^~~~~
>
> The register contains both i3c and i2c specific fields. I'm not sure using
> i2c_i3c_EXTBR is the best way to go forward for this or just keeping it as
> is.
>
> --
> Thank you,
> Claudiu
>

  reply	other threads:[~2026-05-28 19:13 UTC|newest]

Thread overview: 43+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-05-22 10:17 [PATCH 00/17] i3c: renesas: Suspend to RAM with power loss and runtime PM Claudiu Beznea
2026-05-22 10:17 ` [PATCH 01/17] i3c: renesas: Check that the transfer is valid before accessing it Claudiu Beznea
2026-05-22 19:02   ` Frank Li
2026-05-22 10:18 ` [PATCH 02/17] i3c: renesas: Use the divider 128 Claudiu Beznea
2026-05-22 19:06   ` Frank Li
2026-05-23  8:14     ` Claudiu Beznea
2026-05-22 10:18 ` [PATCH 03/17] i3c: renesas: Restore STDBR and EXTBR registers on resume Claudiu Beznea
2026-05-22 19:10   ` Frank Li
2026-05-28  8:29     ` Claudiu Beznea
2026-05-28 19:13       ` Frank Li [this message]
2026-05-22 10:18 ` [PATCH 04/17] i3c: renesas: Follow the reset deassert order used in probe Claudiu Beznea
2026-05-22 19:11   ` Frank Li
2026-05-22 10:18 ` [PATCH 05/17] i3c: renesas: Fix re-attach Claudiu Beznea
2026-05-22 19:13   ` Frank Li
2026-05-22 10:18 ` [PATCH 06/17] i3c: renesas: Reset the controller on resume Claudiu Beznea
2026-05-22 19:15   ` Frank Li
2026-05-23 10:24     ` Claudiu Beznea
2026-05-22 10:18 ` [PATCH 07/17] i3c: renesas: Perform Dynamic Address Assignment " Claudiu Beznea
2026-05-22 19:16   ` Frank Li
2026-05-23 10:26     ` Claudiu Beznea
2026-05-22 10:18 ` [PATCH 08/17] i3c: renesas: Clean DATBAS register on detach Claudiu Beznea
2026-05-22 19:17   ` Frank Li
2026-05-22 10:18 ` [PATCH 09/17] i3c: renesas: Use reset_control_bulk_{assert, deassert}() Claudiu Beznea
2026-05-22 19:19   ` Frank Li
2026-05-23 10:26     ` Claudiu Beznea
2026-05-22 10:18 ` [PATCH 10/17] i3c: renesas: Return immediately if there is nothing to transfer Claudiu Beznea
2026-05-22 19:20   ` Frank Li
2026-05-22 10:18 ` [PATCH 11/17] i3c: renesas: Follow a unified pattern for transfer and command initialization Claudiu Beznea
2026-05-22 19:21   ` Frank Li
2026-05-22 10:18 ` [PATCH 12/17] i3c: renesas: Drop the explicit memset() call Claudiu Beznea
2026-05-22 19:43   ` Frank Li
2026-05-22 10:18 ` [PATCH 13/17] i3c: renesas: Update HW registers after SW computations are done Claudiu Beznea
2026-05-22 19:48   ` Frank Li
2026-05-22 10:18 ` [PATCH 14/17] i3c: renesas: Organize structures to avoid unnecessary padding Claudiu Beznea
2026-05-22 19:50   ` Frank Li
2026-05-22 10:18 ` [PATCH 15/17] i3c: renesas: Use the "dev_name:irq_name" format for the interrupt name Claudiu Beznea
2026-05-22 19:51   ` Frank Li
2026-05-22 10:18 ` [PATCH 16/17] i3c: renesas: Drop unnecessary tab Claudiu Beznea
2026-05-22 19:52   ` Frank Li
2026-05-22 10:18 ` [PATCH 17/17] i3c: renesas: Add runtime PM support Claudiu Beznea
2026-05-22 20:01   ` Frank Li
2026-05-23 10:23     ` Claudiu Beznea
2026-06-02 11:49       ` Claudiu Beznea

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=ahiT1YkbWNz9y4mH@lizhi-Precision-Tower-5810 \
    --to=frank.li@nxp.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=claudiu.beznea.uj@bp.renesas.com \
    --cc=claudiu.beznea@kernel.org \
    --cc=claudiu.beznea@tuxon.dev \
    --cc=linux-i3c@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=p.zabel@pengutronix.de \
    --cc=stable@vger.kernel.org \
    --cc=tommaso.merciai.xr@bp.renesas.com \
    --cc=wsa+renesas@sang-engineering.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®