[PATCH v5 0/6] Add DSC support to DSI video panel

[PATCH v5 0/6] Add DSC support to DSI video panel

[Jun Nie]

This is follow up update to Jonathan's patch set.

Changes vs V4:
- Polish width calculation with helper function
- Split cfg2 compression bit into another patch

Changes vs V3:
- Rebase to latest msm-next-lumag branch.
- Drop the slice_per_pkt change as it does impact basic DSC feature.
- Remove change in generated dsi header
- update DSC compressed width calculation with bpp and bpc
- split wide bus impact on width into another patch
- rename patch tile of VIDEO_COMPRESSION_MODE_CTRL_WC change
- Polish warning usage
- Add tags from reviewers

Changes vs V2:
- Drop the INTF_CFG2_DATA_HCTL_EN change as it is handled in
latest mainline code.
- Drop the bonded DSI patch as I do not have device to test it.
- Address comments from version 2.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
Changes in v5:
- Link to v4: https://lore.kernel.org/r/20240524-msm-drm-dsc-dsi-video-upstream-4-v4-0-e61c05b403df@linaro.org

---
Jonathan Marek (4):
      drm/msm/dpu: fix video mode DSC for DSI
      drm/msm/dsi: set video mode widebus enable bit when widebus is enabled
      drm/msm/dsi: set VIDEO_COMPRESSION_MODE_CTRL_WC
      drm/msm/dsi: add a comment to explain pkt_per_line encoding

Jun Nie (2):
      drm/msm/dpu: adjust data width for widen bus case
      drm/msm/dpu: enable compression bit in cfg2 for DSC

 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c          |  2 +-
 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h     |  8 ++++++++
 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 18 ++++++++++++++++++
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c          | 13 +++++++++++++
 drivers/gpu/drm/msm/dsi/dsi_host.c                   | 10 +++++++++-
 5 files changed, 49 insertions(+), 2 deletions(-)
---
base-commit: e6428bcb611f6c164856a41fc5a1ae8471a9b5a9
change-id: 20240524-msm-drm-dsc-dsi-video-upstream-4-22e2266fbe89

Best regards,
-- 
Jun Nie <jun.nie@linaro.org>

[PATCH v5 1/6] drm/msm/dpu: fix video mode DSC for DSI

[Jun Nie]

From: Jonathan Marek <jonathan@marek.ca>

Add width change in DPU timing for DSC compression case to work with
DSI video mode.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c          |  2 +-
 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h     |  8 ++++++++
 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 18 ++++++++++++++++++
 3 files changed, 27 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
index 119f3ea50a7c..48cef6e79c70 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
@@ -564,7 +564,7 @@ bool dpu_encoder_use_dsc_merge(struct drm_encoder *drm_enc)
 	return (num_dsc > 0) && (num_dsc > intf_count);
 }
 
-static struct drm_dsc_config *dpu_encoder_get_dsc_config(struct drm_encoder *drm_enc)
+struct drm_dsc_config *dpu_encoder_get_dsc_config(struct drm_encoder *drm_enc)
 {
 	struct msm_drm_private *priv = drm_enc->dev->dev_private;
 	struct dpu_encoder_virt *dpu_enc = to_dpu_encoder_virt(drm_enc);
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h
index 002e89cc1705..2167c46c1a45 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h
@@ -334,6 +334,14 @@ static inline enum dpu_3d_blend_mode dpu_encoder_helper_get_3d_blend_mode(
  */
 unsigned int dpu_encoder_helper_get_dsc(struct dpu_encoder_phys *phys_enc);
 
+/**
+ * dpu_encoder_get_dsc_config - get DSC config for the DPU encoder
+ *   This helper function is used by physical encoder to get DSC config
+ *   used for this encoder.
+ * @drm_enc: Pointer to encoder structure
+ */
+struct drm_dsc_config *dpu_encoder_get_dsc_config(struct drm_encoder *drm_enc);
+
 /**
  * dpu_encoder_get_drm_fmt - return DRM fourcc format
  * @phys_enc: Pointer to physical encoder structure
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
index ef69c2f408c3..925ec6ada0e1 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
@@ -11,6 +11,7 @@
 #include "dpu_trace.h"
 #include "disp/msm_disp_snapshot.h"
 
+#include <drm/display/drm_dsc_helper.h>
 #include <drm/drm_managed.h>
 
 #define DPU_DEBUG_VIDENC(e, fmt, ...) DPU_DEBUG("enc%d intf%d " fmt, \
@@ -115,6 +116,23 @@ static void drm_mode_to_intf_timing_params(
 		timing->h_front_porch = timing->h_front_porch >> 1;
 		timing->hsync_pulse_width = timing->hsync_pulse_width >> 1;
 	}
+
+	/*
+	 * for DSI, if compression is enabled, then divide the horizonal active
+	 * timing parameters by compression ratio. bits of 3 components(R/G/B)
+	 * is compressed into bits of 1 pixel.
+	 */
+	if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) {
+		struct drm_dsc_config *dsc =
+		       dpu_encoder_get_dsc_config(phys_enc->parent);
+		/*
+		 * TODO: replace drm_dsc_get_bpp_int with logic to handle
+		 * fractional part if there is fraction
+		 */
+		timing->width = timing->width * drm_dsc_get_bpp_int(dsc) /
+				(dsc->bits_per_component * 3);
+		timing->xres = timing->width;
+	}
 }
 
 static u32 get_horizontal_total(const struct dpu_hw_intf_timing_params *timing)

-- 
2.34.1

Re: [PATCH v5 1/6] drm/msm/dpu: fix video mode DSC for DSI

[Dmitry Baryshkov]

On Mon, May 27, 2024 at 10:21:47PM +0800, Jun Nie wrote:
> From: Jonathan Marek <jonathan@marek.ca>
> 
> Add width change in DPU timing for DSC compression case to work with
> DSI video mode.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> ---
>  drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c          |  2 +-
>  drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h     |  8 ++++++++
>  drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 18 ++++++++++++++++++
>  3 files changed, 27 insertions(+), 1 deletion(-)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>


-- 
With best wishes
Dmitry

Re: [PATCH v5 1/6] drm/msm/dpu: fix video mode DSC for DSI

[Jessica Zhang]

On 5/27/2024 7:21 AM, Jun Nie wrote:
> From: Jonathan Marek <jonathan@marek.ca>
> 
> Add width change in DPU timing for DSC compression case to work with
> DSI video mode.

Hi Jun,

LGTM

Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>

Thanks,

Jessica Zhang

> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> ---
>   drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c          |  2 +-
>   drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h     |  8 ++++++++
>   drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 18 ++++++++++++++++++
>   3 files changed, 27 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
> index 119f3ea50a7c..48cef6e79c70 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
> @@ -564,7 +564,7 @@ bool dpu_encoder_use_dsc_merge(struct drm_encoder *drm_enc)
>   	return (num_dsc > 0) && (num_dsc > intf_count);
>   }
>   
> -static struct drm_dsc_config *dpu_encoder_get_dsc_config(struct drm_encoder *drm_enc)
> +struct drm_dsc_config *dpu_encoder_get_dsc_config(struct drm_encoder *drm_enc)
>   {
>   	struct msm_drm_private *priv = drm_enc->dev->dev_private;
>   	struct dpu_encoder_virt *dpu_enc = to_dpu_encoder_virt(drm_enc);
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h
> index 002e89cc1705..2167c46c1a45 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h
> @@ -334,6 +334,14 @@ static inline enum dpu_3d_blend_mode dpu_encoder_helper_get_3d_blend_mode(
>    */
>   unsigned int dpu_encoder_helper_get_dsc(struct dpu_encoder_phys *phys_enc);
>   
> +/**
> + * dpu_encoder_get_dsc_config - get DSC config for the DPU encoder
> + *   This helper function is used by physical encoder to get DSC config
> + *   used for this encoder.
> + * @drm_enc: Pointer to encoder structure
> + */
> +struct drm_dsc_config *dpu_encoder_get_dsc_config(struct drm_encoder *drm_enc);
> +
>   /**
>    * dpu_encoder_get_drm_fmt - return DRM fourcc format
>    * @phys_enc: Pointer to physical encoder structure
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> index ef69c2f408c3..925ec6ada0e1 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> @@ -11,6 +11,7 @@
>   #include "dpu_trace.h"
>   #include "disp/msm_disp_snapshot.h"
>   
> +#include <drm/display/drm_dsc_helper.h>
>   #include <drm/drm_managed.h>
>   
>   #define DPU_DEBUG_VIDENC(e, fmt, ...) DPU_DEBUG("enc%d intf%d " fmt, \
> @@ -115,6 +116,23 @@ static void drm_mode_to_intf_timing_params(
>   		timing->h_front_porch = timing->h_front_porch >> 1;
>   		timing->hsync_pulse_width = timing->hsync_pulse_width >> 1;
>   	}
> +
> +	/*
> +	 * for DSI, if compression is enabled, then divide the horizonal active
> +	 * timing parameters by compression ratio. bits of 3 components(R/G/B)
> +	 * is compressed into bits of 1 pixel.
> +	 */
> +	if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) {
> +		struct drm_dsc_config *dsc =
> +		       dpu_encoder_get_dsc_config(phys_enc->parent);
> +		/*
> +		 * TODO: replace drm_dsc_get_bpp_int with logic to handle
> +		 * fractional part if there is fraction
> +		 */
> +		timing->width = timing->width * drm_dsc_get_bpp_int(dsc) /
> +				(dsc->bits_per_component * 3);
> +		timing->xres = timing->width;
> +	}
>   }
>   
>   static u32 get_horizontal_total(const struct dpu_hw_intf_timing_params *timing)
> 
> -- 
> 2.34.1
> 

[PATCH v5 2/6] drm/msm/dpu: adjust data width for widen bus case

[Jun Nie]

data is valid for only half the active window if widebus
is enabled

Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
index 225c1c7768ff..f97221423249 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
@@ -168,6 +168,15 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *intf,
 
 	data_width = p->width;
 
+	/*
+	 * If widebus is enabled, data is valid for only half the active window
+	 * since the data rate is doubled in this mode. But for the compression
+	 * mode in DP case, the p->width is already adjusted in
+	 * drm_mode_to_intf_timing_params()
+	 */
+	if (p->wide_bus_en && !dp_intf)
+		data_width = p->width >> 1;
+
 	hsync_data_start_x = hsync_start_x;
 	hsync_data_end_x =  hsync_start_x + data_width - 1;
 

-- 
2.34.1

Re: [PATCH v5 2/6] drm/msm/dpu: adjust data width for widen bus case

[Dmitry Baryshkov]

On Mon, May 27, 2024 at 10:21:48PM +0800, Jun Nie wrote:
> data is valid for only half the active window if widebus
> is enabled
> 
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> ---
>  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 9 +++++++++
>  1 file changed, 9 insertions(+)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> index 225c1c7768ff..f97221423249 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> @@ -168,6 +168,15 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *intf,
>  
>  	data_width = p->width;
>  
> +	/*
> +	 * If widebus is enabled, data is valid for only half the active window
> +	 * since the data rate is doubled in this mode. But for the compression
> +	 * mode in DP case, the p->width is already adjusted in
> +	 * drm_mode_to_intf_timing_params()

Is there any reason for divergence here?

> +	 */
> +	if (p->wide_bus_en && !dp_intf)
> +		data_width = p->width >> 1;
> +
>  	hsync_data_start_x = hsync_start_x;
>  	hsync_data_end_x =  hsync_start_x + data_width - 1;
>  
> 
> -- 
> 2.34.1
> 

-- 
With best wishes
Dmitry

Re: [PATCH v5 2/6] drm/msm/dpu: adjust data width for widen bus case

[Jun Nie]

Dmitry Baryshkov <dmitry.baryshkov@linaro.org> 于2024年5月28日周二 08:48写道：
>
> On Mon, May 27, 2024 at 10:21:48PM +0800, Jun Nie wrote:
> > data is valid for only half the active window if widebus
> > is enabled
> >
> > Signed-off-by: Jun Nie <jun.nie@linaro.org>
> > ---
> >  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 9 +++++++++
> >  1 file changed, 9 insertions(+)
> >
> > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> > index 225c1c7768ff..f97221423249 100644
> > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> > @@ -168,6 +168,15 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *intf,
> >
> >       data_width = p->width;
> >
> > +     /*
> > +      * If widebus is enabled, data is valid for only half the active window
> > +      * since the data rate is doubled in this mode. But for the compression
> > +      * mode in DP case, the p->width is already adjusted in
> > +      * drm_mode_to_intf_timing_params()
>
> Is there any reason for divergence here?

Lots of parameters in dpu_hw_intf_setup_timing_engine() is calculated
from timing->width,
such as hsync_period and display_v_start. So the width cannot be
adjusted beforehand in
drm_mode_to_intf_timing_params(). Otherwise, we get below error.

I guess the interface timing configuration differ in silicon, thus the
software shall handle the
difference. If we adjust the width beforehand for DSI, we get below error.

[    6.625446] [drm:dpu_encoder_frame_done_timeout:2469] [dpu
error]enc31 frame done timeout
[    6.642369] [drm:dpu_encoder_phys_vid_wait_for_commit_done:525]
[dpu error]vblank timeout: 4200c1
[    6.642395] [drm:dpu_kms_wait_for_commit_done:493] [dpu error]wait
for commit done returned -110


>
> > +      */
> > +     if (p->wide_bus_en && !dp_intf)
> > +             data_width = p->width >> 1;
> > +
> >       hsync_data_start_x = hsync_start_x;
> >       hsync_data_end_x =  hsync_start_x + data_width - 1;
> >
> >
> > --
> > 2.34.1
> >
>
> --
> With best wishes
> Dmitry

Re: [PATCH v5 2/6] drm/msm/dpu: adjust data width for widen bus case

[Dmitry Baryshkov]

On Tue, May 28, 2024 at 05:59:13PM +0800, Jun Nie wrote:
> Dmitry Baryshkov <dmitry.baryshkov@linaro.org> 于2024年5月28日周二 08:48写道：
> >
> > On Mon, May 27, 2024 at 10:21:48PM +0800, Jun Nie wrote:
> > > data is valid for only half the active window if widebus
> > > is enabled
> > >
> > > Signed-off-by: Jun Nie <jun.nie@linaro.org>
> > > ---
> > >  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 9 +++++++++
> > >  1 file changed, 9 insertions(+)
> > >
> > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> > > index 225c1c7768ff..f97221423249 100644
> > > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> > > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> > > @@ -168,6 +168,15 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *intf,
> > >
> > >       data_width = p->width;
> > >
> > > +     /*
> > > +      * If widebus is enabled, data is valid for only half the active window
> > > +      * since the data rate is doubled in this mode. But for the compression
> > > +      * mode in DP case, the p->width is already adjusted in
> > > +      * drm_mode_to_intf_timing_params()
> >
> > Is there any reason for divergence here?
> 
> Lots of parameters in dpu_hw_intf_setup_timing_engine() is calculated
> from timing->width,
> such as hsync_period and display_v_start. So the width cannot be
> adjusted beforehand in
> drm_mode_to_intf_timing_params(). Otherwise, we get below error.
> 
> I guess the interface timing configuration differ in silicon, thus the
> software shall handle the
> difference. If we adjust the width beforehand for DSI, we get below error.
> 
> [    6.625446] [drm:dpu_encoder_frame_done_timeout:2469] [dpu
> error]enc31 frame done timeout
> [    6.642369] [drm:dpu_encoder_phys_vid_wait_for_commit_done:525]
> [dpu error]vblank timeout: 4200c1
> [    6.642395] [drm:dpu_kms_wait_for_commit_done:493] [dpu error]wait
> for commit done returned -110
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>


-- 
With best wishes
Dmitry

Re: [PATCH v5 2/6] drm/msm/dpu: adjust data width for widen bus case

[Jessica Zhang]

On 5/27/2024 7:21 AM, Jun Nie wrote:
> data is valid for only half the active window if widebus
> is enabled
> 
> Signed-off-by: Jun Nie <jun.nie@linaro.org>

Hi Jun,

Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>

Thanks,

Jessica Zhang

> ---
>   drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 9 +++++++++
>   1 file changed, 9 insertions(+)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> index 225c1c7768ff..f97221423249 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> @@ -168,6 +168,15 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *intf,
>   
>   	data_width = p->width;
>   
> +	/*
> +	 * If widebus is enabled, data is valid for only half the active window
> +	 * since the data rate is doubled in this mode. But for the compression
> +	 * mode in DP case, the p->width is already adjusted in
> +	 * drm_mode_to_intf_timing_params()
> +	 */
> +	if (p->wide_bus_en && !dp_intf)
> +		data_width = p->width >> 1;
> +
>   	hsync_data_start_x = hsync_start_x;
>   	hsync_data_end_x =  hsync_start_x + data_width - 1;
>   
> 
> -- 
> 2.34.1
> 

[PATCH v5 3/6] drm/msm/dpu: enable compression bit in cfg2 for DSC

[Jun Nie]

Enable compression bit in cfg2 register for DSC in the DSI case

Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
index f97221423249..34bfcfba3df2 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
@@ -177,6 +177,10 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *intf,
 	if (p->wide_bus_en && !dp_intf)
 		data_width = p->width >> 1;
 
+	/* TODO: handle DSC+DP case, we only handle DSC+DSI case so far */
+	if (p->compression_en && !dp_intf)
+		intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS;
+
 	hsync_data_start_x = hsync_start_x;
 	hsync_data_end_x =  hsync_start_x + data_width - 1;
 

-- 
2.34.1

Re: [PATCH v5 3/6] drm/msm/dpu: enable compression bit in cfg2 for DSC

[Dmitry Baryshkov]

On Mon, May 27, 2024 at 10:21:49PM +0800, Jun Nie wrote:
> Enable compression bit in cfg2 register for DSC in the DSI case
> 
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> ---
>  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 4 ++++
>  1 file changed, 4 insertions(+)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>


-- 
With best wishes
Dmitry

Re: [PATCH v5 3/6] drm/msm/dpu: enable compression bit in cfg2 for DSC

[Jessica Zhang]

On 5/27/2024 7:21 AM, Jun Nie wrote:
> Enable compression bit in cfg2 register for DSC in the DSI case
> 
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> ---
>   drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 4 ++++
>   1 file changed, 4 insertions(+)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> index f97221423249..34bfcfba3df2 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> @@ -177,6 +177,10 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *intf,
>   	if (p->wide_bus_en && !dp_intf)
>   		data_width = p->width >> 1;
>   
> +	/* TODO: handle DSC+DP case, we only handle DSC+DSI case so far */
> +	if (p->compression_en && !dp_intf)
> +		intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS;

Hi Jun,

The DSC/DCE enablement registers were only moved to INTF in DPU 7.x and 
later.

We should probably add some MDSS version check similar to what command 
mode INTF does here [1]

Thanks,

Jessica Zhang

> +
>   	hsync_data_start_x = hsync_start_x;
>   	hsync_data_end_x =  hsync_start_x + data_width - 1;
>   
> 
> -- 
> 2.34.1
> 

[PATCH v5 4/6] drm/msm/dsi: set video mode widebus enable bit when widebus is enabled

[Jun Nie]

From: Jonathan Marek <jonathan@marek.ca>

The value returned by msm_dsi_wide_bus_enabled() doesn't match what the
driver is doing in video mode. Fix that by actually enabling widebus for
video mode.

Fixes: efcbd6f9cdeb ("drm/msm/dsi: Enable widebus for DSI")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c
index a50f4dda5941..47f5858334f6 100644
--- a/drivers/gpu/drm/msm/dsi/dsi_host.c
+++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
@@ -754,6 +754,8 @@ static void dsi_ctrl_enable(struct msm_dsi_host *msm_host,
 		data |= DSI_VID_CFG0_TRAFFIC_MODE(dsi_get_traffic_mode(flags));
 		data |= DSI_VID_CFG0_DST_FORMAT(dsi_get_vid_fmt(mipi_fmt));
 		data |= DSI_VID_CFG0_VIRT_CHANNEL(msm_host->channel);
+		if (msm_dsi_host_is_wide_bus_enabled(&msm_host->base))
+			data |= DSI_VID_CFG0_DATABUS_WIDEN;
 		dsi_write(msm_host, REG_DSI_VID_CFG0, data);
 
 		/* Do not swap RGB colors */
@@ -778,7 +780,6 @@ static void dsi_ctrl_enable(struct msm_dsi_host *msm_host,
 			if (cfg_hnd->minor >= MSM_DSI_6G_VER_MINOR_V1_3)
 				data |= DSI_CMD_MODE_MDP_CTRL2_BURST_MODE;
 
-			/* TODO: Allow for video-mode support once tested/fixed */
 			if (msm_dsi_host_is_wide_bus_enabled(&msm_host->base))
 				data |= DSI_CMD_MODE_MDP_CTRL2_DATABUS_WIDEN;
 

-- 
2.34.1

[PATCH v5 5/6] drm/msm/dsi: set VIDEO_COMPRESSION_MODE_CTRL_WC

[Jun Nie]

From: Jonathan Marek <jonathan@marek.ca>

Video mode DSC won't work if this field is not set correctly. Set it to fix
video mode DSC (for slice_per_pkt==1 cases at least).

Fixes: 08802f515c3c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c
index 47f5858334f6..7252d36687e6 100644
--- a/drivers/gpu/drm/msm/dsi/dsi_host.c
+++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
@@ -857,6 +857,7 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
 	u32 slice_per_intf, total_bytes_per_intf;
 	u32 pkt_per_line;
 	u32 eol_byte_num;
+	u32 bytes_per_pkt;
 
 	/* first calculate dsc parameters and then program
 	 * compress mode registers
@@ -864,6 +865,7 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
 	slice_per_intf = msm_dsc_get_slices_per_intf(dsc, hdisplay);
 
 	total_bytes_per_intf = dsc->slice_chunk_size * slice_per_intf;
+	bytes_per_pkt = dsc->slice_chunk_size; /* * slice_per_pkt; */
 
 	eol_byte_num = total_bytes_per_intf % 3;
 
@@ -901,6 +903,7 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
 		dsi_write(msm_host, REG_DSI_COMMAND_COMPRESSION_MODE_CTRL, reg_ctrl);
 		dsi_write(msm_host, REG_DSI_COMMAND_COMPRESSION_MODE_CTRL2, reg_ctrl2);
 	} else {
+		reg |= DSI_VIDEO_COMPRESSION_MODE_CTRL_WC(bytes_per_pkt);
 		dsi_write(msm_host, REG_DSI_VIDEO_COMPRESSION_MODE_CTRL, reg);
 	}
 }

-- 
2.34.1

Re: [PATCH v5 5/6] drm/msm/dsi: set VIDEO_COMPRESSION_MODE_CTRL_WC

[Jessica Zhang]

On 5/27/2024 7:21 AM, Jun Nie wrote:
> From: Jonathan Marek <jonathan@marek.ca>
> 
> Video mode DSC won't work if this field is not set correctly. Set it to fix
> video mode DSC (for slice_per_pkt==1 cases at least).
> 
> Fixes: 08802f515c3c ("drm/msm/dsi: Add support for DSC configuration")
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>

Hi Jun,

Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>

Thanks,

Jessica Zhang

> ---
>   drivers/gpu/drm/msm/dsi/dsi_host.c | 3 +++
>   1 file changed, 3 insertions(+)
> 
> diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c
> index 47f5858334f6..7252d36687e6 100644
> --- a/drivers/gpu/drm/msm/dsi/dsi_host.c
> +++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
> @@ -857,6 +857,7 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
>   	u32 slice_per_intf, total_bytes_per_intf;
>   	u32 pkt_per_line;
>   	u32 eol_byte_num;
> +	u32 bytes_per_pkt;
>   
>   	/* first calculate dsc parameters and then program
>   	 * compress mode registers
> @@ -864,6 +865,7 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
>   	slice_per_intf = msm_dsc_get_slices_per_intf(dsc, hdisplay);
>   
>   	total_bytes_per_intf = dsc->slice_chunk_size * slice_per_intf;
> +	bytes_per_pkt = dsc->slice_chunk_size; /* * slice_per_pkt; */
>   
>   	eol_byte_num = total_bytes_per_intf % 3;
>   
> @@ -901,6 +903,7 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
>   		dsi_write(msm_host, REG_DSI_COMMAND_COMPRESSION_MODE_CTRL, reg_ctrl);
>   		dsi_write(msm_host, REG_DSI_COMMAND_COMPRESSION_MODE_CTRL2, reg_ctrl2);
>   	} else {
> +		reg |= DSI_VIDEO_COMPRESSION_MODE_CTRL_WC(bytes_per_pkt);
>   		dsi_write(msm_host, REG_DSI_VIDEO_COMPRESSION_MODE_CTRL, reg);
>   	}
>   }
> 
> -- 
> 2.34.1
> 

[PATCH v5 6/6] drm/msm/dsi: add a comment to explain pkt_per_line encoding

[Jun Nie]

From: Jonathan Marek <jonathan@marek.ca>

Make it clear why the pkt_per_line value is being "divided by 2".

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c
index 7252d36687e6..4768cff08381 100644
--- a/drivers/gpu/drm/msm/dsi/dsi_host.c
+++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
@@ -885,7 +885,11 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
 	/* DSI_VIDEO_COMPRESSION_MODE & DSI_COMMAND_COMPRESSION_MODE
 	 * registers have similar offsets, so for below common code use
 	 * DSI_VIDEO_COMPRESSION_MODE_XXXX for setting bits
+	 *
+	 * pkt_per_line is log2 encoded, >>1 works for supported values (1,2,4)
 	 */
+	if (pkt_per_line > 4)
+		drm_warn_once(msm_host->dev, "pkt_per_line too big");
 	reg |= DSI_VIDEO_COMPRESSION_MODE_CTRL_PKT_PER_LINE(pkt_per_line >> 1);
 	reg |= DSI_VIDEO_COMPRESSION_MODE_CTRL_EOL_BYTE_NUM(eol_byte_num);
 	reg |= DSI_VIDEO_COMPRESSION_MODE_CTRL_EN;

-- 
2.34.1

Re: [PATCH v5 6/6] drm/msm/dsi: add a comment to explain pkt_per_line encoding

[Jessica Zhang]

On 5/27/2024 7:21 AM, Jun Nie wrote:
> From: Jonathan Marek <jonathan@marek.ca>
> 
> Make it clear why the pkt_per_line value is being "divided by 2".
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>

Hi Jun,

Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>

Thanks,

Jessica Zhang

> ---
>   drivers/gpu/drm/msm/dsi/dsi_host.c | 4 ++++
>   1 file changed, 4 insertions(+)
> 
> diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c
> index 7252d36687e6..4768cff08381 100644
> --- a/drivers/gpu/drm/msm/dsi/dsi_host.c
> +++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
> @@ -885,7 +885,11 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
>   	/* DSI_VIDEO_COMPRESSION_MODE & DSI_COMMAND_COMPRESSION_MODE
>   	 * registers have similar offsets, so for below common code use
>   	 * DSI_VIDEO_COMPRESSION_MODE_XXXX for setting bits
> +	 *
> +	 * pkt_per_line is log2 encoded, >>1 works for supported values (1,2,4)
>   	 */
> +	if (pkt_per_line > 4)
> +		drm_warn_once(msm_host->dev, "pkt_per_line too big");
>   	reg |= DSI_VIDEO_COMPRESSION_MODE_CTRL_PKT_PER_LINE(pkt_per_line >> 1);
>   	reg |= DSI_VIDEO_COMPRESSION_MODE_CTRL_EOL_BYTE_NUM(eol_byte_num);
>   	reg |= DSI_VIDEO_COMPRESSION_MODE_CTRL_EN;
> 
> -- 
> 2.34.1
> 

Re: [PATCH v5 0/6] Add DSC support to DSI video panel

[neil.armstrong]

On 27/05/2024 16:21, Jun Nie wrote:
> This is follow up update to Jonathan's patch set.
> 
> Changes vs V4:
> - Polish width calculation with helper function
> - Split cfg2 compression bit into another patch
> 
> Changes vs V3:
> - Rebase to latest msm-next-lumag branch.
> - Drop the slice_per_pkt change as it does impact basic DSC feature.
> - Remove change in generated dsi header
> - update DSC compressed width calculation with bpp and bpc
> - split wide bus impact on width into another patch
> - rename patch tile of VIDEO_COMPRESSION_MODE_CTRL_WC change
> - Polish warning usage
> - Add tags from reviewers
> 
> Changes vs V2:
> - Drop the INTF_CFG2_DATA_HCTL_EN change as it is handled in
> latest mainline code.
> - Drop the bonded DSI patch as I do not have device to test it.
> - Address comments from version 2.
> 
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> ---
> Changes in v5:
> - Link to v4: https://lore.kernel.org/r/20240524-msm-drm-dsc-dsi-video-upstream-4-v4-0-e61c05b403df@linaro.org
> 
> ---
> Jonathan Marek (4):
>        drm/msm/dpu: fix video mode DSC for DSI
>        drm/msm/dsi: set video mode widebus enable bit when widebus is enabled
>        drm/msm/dsi: set VIDEO_COMPRESSION_MODE_CTRL_WC
>        drm/msm/dsi: add a comment to explain pkt_per_line encoding
> 
> Jun Nie (2):
>        drm/msm/dpu: adjust data width for widen bus case
>        drm/msm/dpu: enable compression bit in cfg2 for DSC
> 
>   drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c          |  2 +-
>   drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h     |  8 ++++++++
>   drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 18 ++++++++++++++++++
>   drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c          | 13 +++++++++++++
>   drivers/gpu/drm/msm/dsi/dsi_host.c                   | 10 +++++++++-
>   5 files changed, 49 insertions(+), 2 deletions(-)
> ---
> base-commit: e6428bcb611f6c164856a41fc5a1ae8471a9b5a9
> change-id: 20240524-msm-drm-dsc-dsi-video-upstream-4-22e2266fbe89
> 
> Best regards,

Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK

with https://lore.kernel.org/all/20230728012623.22991-1-quic_parellan@quicinc.com/ and enforce-video-mode in panel node.

Thanks,
Neil