From: Mike Frysinger <vapier@gentoo.org>
To: linux-kernel@vger.kernel.org
Cc: uclinux-dist-devel@blackfin.uclinux.org
Subject: [PATCH 51/72] Blackfin: drop board resources for dead devices (pbx/ad9960)
Date: Mon, 14 Sep 2009 16:07:55 -0400 [thread overview]
Message-ID: <1252958896-25150-52-git-send-email-vapier@gentoo.org> (raw)
In-Reply-To: <1252958896-25150-1-git-send-email-vapier@gentoo.org>
These hardware devices are dead and the drivers never cleaned up/merged,
so punt the useless board resource info.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
arch/blackfin/mach-bf518/boards/ezbrd.c | 27 ----------------
arch/blackfin/mach-bf527/boards/cm_bf527.c | 43 --------------------------
arch/blackfin/mach-bf527/boards/ezbrd.c | 27 ----------------
arch/blackfin/mach-bf527/boards/ezkit.c | 43 --------------------------
arch/blackfin/mach-bf533/boards/H8606.c | 26 ----------------
arch/blackfin/mach-bf533/boards/stamp.c | 28 -----------------
arch/blackfin/mach-bf537/boards/cm_bf537.c | 17 ----------
arch/blackfin/mach-bf537/boards/pnav10.c | 16 ----------
arch/blackfin/mach-bf537/boards/stamp.c | 44 ---------------------------
arch/blackfin/mach-bf537/boards/tcm_bf537.c | 17 ----------
arch/blackfin/mach-bf561/boards/cm_bf561.c | 16 ----------
11 files changed, 0 insertions(+), 304 deletions(-)
diff --git a/arch/blackfin/mach-bf518/boards/ezbrd.c b/arch/blackfin/mach-bf518/boards/ezbrd.c
index 4c594e6..03e4a99 100644
--- a/arch/blackfin/mach-bf518/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf518/boards/ezbrd.c
@@ -199,15 +199,6 @@ static struct bfin5xx_spi_chip mmc_spi_chip_info = {
};
#endif
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
- .ctl_reg = 0x4, /* send zero */
- .enable_dma = 0,
- .bits_per_word = 8,
- .cs_change_per_word = 1,
-};
-#endif
-
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
@@ -296,24 +287,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_PBX)
- {
- .modalias = "fxs-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J11_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "fxo-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J19_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
{
.modalias = "ad7877",
diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index 18b9bd7..fdd518c 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -495,13 +495,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
};
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -509,15 +502,6 @@ static struct bfin5xx_spi_chip mmc_spi_chip_info = {
};
#endif
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
- .ctl_reg = 0x4, /* send zero */
- .enable_dma = 0,
- .bits_per_word = 8,
- .cs_change_per_word = 1,
-};
-#endif
-
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
@@ -591,15 +575,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.controller_data = &ad1836_spi_chip_info,
},
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
- {
- .modalias = "ad9960-spi",
- .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- .controller_data = &ad9960_spi_chip_info,
- },
-#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
@@ -610,24 +585,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_PBX)
- {
- .modalias = "fxs-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J11_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "fxo-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J19_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
{
.modalias = "ad7877",
diff --git a/arch/blackfin/mach-bf527/boards/ezbrd.c b/arch/blackfin/mach-bf527/boards/ezbrd.c
index 809c790..68b4c80 100644
--- a/arch/blackfin/mach-bf527/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf527/boards/ezbrd.c
@@ -263,15 +263,6 @@ static struct bfin5xx_spi_chip mmc_spi_chip_info = {
};
#endif
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
- .ctl_reg = 0x4, /* send zero */
- .enable_dma = 0,
- .bits_per_word = 8,
- .cs_change_per_word = 1,
-};
-#endif
-
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
@@ -376,24 +367,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_PBX)
- {
- .modalias = "fxs-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J11_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "fxo-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J19_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
{
.modalias = "ad7877",
diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index 617a287..4ab9cfa 100644
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -512,13 +512,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
};
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -526,15 +519,6 @@ static struct bfin5xx_spi_chip mmc_spi_chip_info = {
};
#endif
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
- .ctl_reg = 0x4, /* send zero */
- .enable_dma = 0,
- .bits_per_word = 8,
- .cs_change_per_word = 1,
-};
-#endif
-
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
@@ -632,15 +616,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.controller_data = &ad1836_spi_chip_info,
},
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
- {
- .modalias = "ad9960-spi",
- .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- .controller_data = &ad9960_spi_chip_info,
- },
-#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
@@ -652,24 +627,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_PBX)
- {
- .modalias = "fxs-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J11_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "fxo-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J19_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
{
.modalias = "ad7877",
diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c
index 1bd8b61..30ff3c4 100644
--- a/arch/blackfin/mach-bf533/boards/H8606.c
+++ b/arch/blackfin/mach-bf533/boards/H8606.c
@@ -201,15 +201,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
};
#endif
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
- .ctl_reg = 0x1c04,
- .enable_dma = 0,
- .bits_per_word = 8,
- .cs_change_per_word = 1,
-};
-#endif
-
/* Notice: for blackfin, the speed_hz is the value of register
* SPI_BAUD, not the real baudrate */
static struct spi_board_info bfin_spi_board_info[] __initdata = {
@@ -248,23 +239,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_PBX)
- {
- .modalias = "fxs-spi",
- .max_speed_hz = 4,
- .bus_num = 1,
- .chip_select = 3,
- .controller_data = &spi_si3xxx_chip_info,
- },
-
- {
- .modalias = "fxo-spi",
- .max_speed_hz = 4,
- .bus_num = 1,
- .chip_select = 2,
- .controller_data = &spi_si3xxx_chip_info,
- },
-#endif
};
/* SPI (0) */
diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index f3dc283..3954baa 100644
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -219,15 +219,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
};
#endif
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
- .ctl_reg = 0x4, /* send zero */
- .enable_dma = 0,
- .bits_per_word = 8,
- .cs_change_per_word = 1,
-};
-#endif
-
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
@@ -298,25 +289,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_PBX)
- {
- .modalias = "fxs-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J11_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "fxo-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J19_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
-
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
{
.modalias = "spidev",
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
index 3681d2c..159e5b2 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c
@@ -101,13 +101,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
};
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -150,16 +143,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
- {
- .modalias = "ad9960-spi",
- .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- .controller_data = &ad9960_spi_chip_info,
- },
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c
index 3bbe102..0d93bbe 100644
--- a/arch/blackfin/mach-bf537/boards/pnav10.c
+++ b/arch/blackfin/mach-bf537/boards/pnav10.c
@@ -293,13 +293,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
};
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -366,15 +359,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.controller_data = &ad1836_spi_chip_info,
},
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
- {
- .modalias = "ad9960-spi",
- .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- .controller_data = &ad9960_spi_chip_info,
- },
-#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index d438ca4..d5aabee 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -549,13 +549,6 @@ static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
};
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
#include <linux/input.h>
#include <linux/input/ad714x.h>
@@ -698,15 +691,6 @@ static struct bfin5xx_spi_chip mmc_spi_chip_info = {
};
#endif
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
- .ctl_reg = 0x4, /* send zero */
- .enable_dma = 0,
- .bits_per_word = 8,
- .cs_change_per_word = 1,
-};
-#endif
-
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
#include <linux/spi/ad7877.h>
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
@@ -906,16 +890,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
- {
- .modalias = "ad9960-spi",
- .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- .controller_data = &ad9960_spi_chip_info,
- },
-#endif
-
#if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
{
.modalias = "ad714x_captouch",
@@ -940,24 +914,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_PBX)
- {
- .modalias = "fxs-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J11_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "fxo-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J19_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
{
.modalias = "ad7877",
diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
index 97a86b4..88eade8 100644
--- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
@@ -101,13 +101,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
};
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -150,16 +143,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
- {
- .modalias = "ad9960-spi",
- .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- .controller_data = &ad9960_spi_chip_info,
- },
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index ebb0755..cedcc3c 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -98,13 +98,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
};
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -146,15 +139,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.controller_data = &ad1836_spi_chip_info,
},
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
- {
- .modalias = "ad9960-spi",
- .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- .controller_data = &ad9960_spi_chip_info,
- },
-#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
--
1.6.4.2
next prev parent reply other threads:[~2009-09-14 20:09 UTC|newest]
Thread overview: 86+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-09-14 20:07 [PATCH 00/72] Blackfin updates for 2.6.32 Mike Frysinger
2009-09-14 20:07 ` [PATCH 01/72] Blackfin: bf537-stamp: update ADP5588 header name Mike Frysinger
2009-09-14 20:07 ` [PATCH 02/72] Blackfin: bf537-stamp: declare SPI IRQ resources Mike Frysinger
2009-09-14 20:07 ` [PATCH 03/72] Blackfin: bf537-stamp: add resources for AD1938 audio card Mike Frysinger
2009-09-14 20:07 ` [PATCH 04/72] Blackfin: make EVT3->EVT5 lowering more robust wrt IPEND[4] Mike Frysinger
2009-09-14 20:07 ` [PATCH 05/72] Blackfin: checkpatch --file arch/blackfin/kernel/ipipe.c Mike Frysinger
2009-09-14 20:07 ` [PATCH 06/72] Blackfin: fix misnomer of some I-pipe helpers Mike Frysinger
2009-09-14 20:07 ` [PATCH 07/72] Blackfin: export show_stack() to modules Mike Frysinger
2009-09-14 20:07 ` [PATCH 08/72] Blackfin: allow high priority domains to preempt schedule_tail() Mike Frysinger
2009-09-14 20:07 ` [PATCH 09/72] Blackfin: use generic name for EVT14 handler Mike Frysinger
2009-09-14 20:07 ` [PATCH 10/72] Blackfin: reuse evt_evt14 handler to perform irqtail epilogue Mike Frysinger
2009-09-14 20:07 ` [PATCH 11/72] Blackfin: allow EVT5 to preempt irqtail prologue (CONFIG_DEBUG_HWERR) Mike Frysinger
2009-09-14 20:07 ` [PATCH 12/72] Blackfin: document __ipipe_call_irqtail Mike Frysinger
2009-09-14 20:07 ` [PATCH 13/72] Blackfin: sanitize manual control of IPEND[4] Mike Frysinger
2009-09-14 20:07 ` [PATCH 14/72] Blackfin: inline I-pipe bypass code in ret_from_exception Mike Frysinger
2009-09-14 20:07 ` [PATCH 15/72] Blackfin: cleanup traps decode_address() a bit Mike Frysinger
2009-09-14 20:07 ` [PATCH 16/72] Blackfin: convert ptrace to new memory functions Mike Frysinger
2009-09-14 20:07 ` [PATCH 17/72] Blackfin: reject outdated/unused/wrong relocation types Mike Frysinger
2009-09-14 20:07 ` [PATCH 18/72] Blackfin: cleanup printk() usage in module code Mike Frysinger
2009-09-14 20:07 ` [PATCH 19/72] Blackfin: convert malloc()/memset() to zalloc() " Mike Frysinger
2009-09-14 20:07 ` [PATCH 20/72] Blackfin: cleanup module section checking Mike Frysinger
2009-09-14 20:07 ` [PATCH 21/72] Blackfin: fix module reloc handling for all memory regions Mike Frysinger
2009-09-14 20:07 ` [PATCH 22/72] Blackfin: clean up early memory setup code Mike Frysinger
2009-09-14 20:07 ` [PATCH 23/72] Blackfin: rename PCF8574 driver config Mike Frysinger
2009-09-14 20:07 ` [PATCH 24/72] Blackfin: unify duplicated SMP checks in L2 cache kconfig Mike Frysinger
2009-09-14 20:07 ` [PATCH 25/72] Blackfin: push SRAM locks down into related ifdefs Mike Frysinger
2009-09-14 20:07 ` [PATCH 26/72] Blackfin: add support for common FDPIC ptrace requests Mike Frysinger
2009-09-14 20:07 ` [PATCH 27/72] Blackfin: add an early shadow console Mike Frysinger
2009-09-14 20:07 ` [PATCH 28/72] Blackfin: catch hardware errors earlier during booting Mike Frysinger
2009-09-14 20:07 ` [PATCH 29/72] Blackfin: fix BF548 UART0 DMA IRQ translation Mike Frysinger
2009-09-14 20:07 ` [PATCH 30/72] Blackfin: bf538: add bfin_clear_PPI_STATUS() helper Mike Frysinger
2009-09-14 20:07 ` [PATCH 31/72] Blackfin: bf533-stamp: add resources for mmc_spi card Mike Frysinger
2009-09-14 20:07 ` [PATCH 32/72] Blackfin: do not try displaying the end of the stack Mike Frysinger
2009-09-14 20:07 ` [PATCH 33/72] Blackfin: bf537-stamp: update AD714x resources Mike Frysinger
2009-09-14 20:07 ` [PATCH 34/72] Blackfin: clean up duplicate I2C device type definitions Mike Frysinger
2009-09-14 20:07 ` [PATCH 35/72] Blackfin: fix MPU handling of invalid memory accesses Mike Frysinger
2009-09-14 20:07 ` [PATCH 36/72] Blackfin: bf533-stamp: fix typo in SPI frequency for ad1836 codec Mike Frysinger
2009-09-14 20:07 ` [PATCH 37/72] Blackfin: improve double fault debug handling Mike Frysinger
2009-09-14 20:07 ` [PATCH 38/72] Blackfin: bf537-stamp: drop ATA interrupt probe workaround Mike Frysinger
2009-09-14 20:07 ` [PATCH 39/72] Blackfin: convert boards to use platform data with smc91x Mike Frysinger
2009-09-14 20:07 ` [PATCH 40/72] Blackfin: drop unused MMR defines that only cause bad code to be written Mike Frysinger
2009-09-14 20:07 ` [PATCH 41/72] Blackfin: cm-bf527/bf537-stamp: fix dm9000 resources Mike Frysinger
2009-09-14 20:07 ` [PATCH 42/72] Blackfin: bf548-ezkit: fix incorrect LCD size parameters Mike Frysinger
2009-09-14 20:07 ` [PATCH 43/72] Blackfin: fix read buffer overflow Mike Frysinger
2009-09-14 20:07 ` [PATCH 44/72] Blackfin: bf538-ezkit: add resources for parallel flash Mike Frysinger
2009-09-14 20:07 ` [PATCH 45/72] Blackfin: update anomaly lists Mike Frysinger
2009-09-14 20:07 ` [PATCH 46/72] Blackfin: bf537-stamp: update ad1836 resources Mike Frysinger
2009-09-14 20:07 ` [PATCH 47/72] Blackfin: cleanup sync handling when enabling/disabling cplbs Mike Frysinger
2009-09-14 20:07 ` [PATCH 48/72] Blackfin: SMP port does not yet support cpu frequency scaling Mike Frysinger
2009-09-14 20:07 ` [PATCH 49/72] Blackfin: fix BF522/BF523 max VCO mixup Mike Frysinger
2009-09-14 20:07 ` [PATCH 50/72] Blackfin: do not trace the exception handler Mike Frysinger
2009-09-14 20:07 ` Mike Frysinger [this message]
2009-09-14 20:07 ` [PATCH 52/72] Blackfin: punt dead cache locking code Mike Frysinger
2009-09-14 20:07 ` [PATCH 53/72] Blackfin: delete '-spi' suffix in ad1836/ad1938 driver name Mike Frysinger
2009-09-14 20:07 ` [PATCH 54/72] Blackfin: optimize fixed code handling for the most common case Mike Frysinger
2009-09-14 20:07 ` [PATCH 55/72] Blackfin: handle the core timer interrupt with handle_percpu_irq on SMP Mike Frysinger
2009-09-14 20:08 ` [PATCH 56/72] Blackfin: Fix link errors with binutils 2.19 and GCC 4.3 Mike Frysinger
2009-09-14 20:08 ` [PATCH 57/72] Blackfin: remove useless duplicated assignment in gpio code Mike Frysinger
2009-09-14 20:08 ` [PATCH 58/72] Blackfin: use raw_smp_processor_id() in exception code Mike Frysinger
2009-09-14 20:08 ` [PATCH 59/72] Blackfin: fix spelling in a few comments Mike Frysinger
2009-09-14 20:08 ` [PATCH 60/72] Blackfin: workaround anomaly 05000283 Mike Frysinger
2009-09-14 20:08 ` [PATCH 61/72] Blackfin: add some isram-driver self tests Mike Frysinger
2009-09-14 20:08 ` [PATCH 62/72] Blackfin: bf537-stamp: add adp5588 gpio resources Mike Frysinger
2009-09-14 20:08 ` [PATCH 63/72] Blackfin: fix typo in isram_write() Mike Frysinger
2009-09-14 20:08 ` [PATCH 64/72] Blackfin: fix BF54x SPI CS resources Mike Frysinger
2009-09-14 20:08 ` [PATCH 65/72] Blackfin: use KERN_ALERT in all kgdb_test output Mike Frysinger
2009-09-14 20:08 ` [PATCH 66/72] Blackfin: add ICPLB coverage for async banks Mike Frysinger
2009-09-14 20:08 ` [PATCH 67/72] Blackfin: increase default async timings for parallel flashes Mike Frysinger
2009-09-14 20:08 ` [PATCH 68/72] Blackfin: bf538-ezkit: add SPI IRQ resources Mike Frysinger
2009-09-14 20:08 ` [PATCH 69/72] Blackfin: cm-bf537u: split board from cm-bf537e Mike Frysinger
2009-09-14 20:08 ` [PATCH 70/72] Blackfin: update cm board resources Mike Frysinger
2009-09-14 20:08 ` [PATCH 71/72] Blackfin: update ftrace_push_return_trace() breakage Mike Frysinger
2009-09-14 20:08 ` [PATCH 72/72] Blackfin: swap clocksource ratings for gptimer/cycles Mike Frysinger
2009-09-14 20:50 ` [PATCH 00/72] Blackfin updates for 2.6.32 Daniel Walker
2009-09-14 20:57 ` Mike Frysinger
2009-09-14 21:04 ` Daniel Walker
2009-09-14 21:07 ` Mike Frysinger
2009-09-14 21:21 ` Daniel Walker
2009-09-14 22:17 ` Mike Frysinger
2009-09-14 22:36 ` Daniel Walker
2009-09-16 2:54 ` Mike Frysinger
2009-09-16 2:56 ` Mike Frysinger
2009-09-16 3:06 ` Daniel Walker
2009-09-16 3:21 ` Mike Frysinger
2009-09-16 3:59 ` Daniel Walker
2009-09-16 4:13 ` Mike Frysinger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1252958896-25150-52-git-send-email-vapier@gentoo.org \
--to=vapier@gentoo.org \
--cc=linux-kernel@vger.kernel.org \
--cc=uclinux-dist-devel@blackfin.uclinux.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®