From: Mike Frysinger <vapier@gentoo.org>
To: linux-kernel@vger.kernel.org
Cc: uclinux-dist-devel@blackfin.uclinux.org,
Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Subject: [PATCH 70/72] Blackfin: update cm board resources
Date: Mon, 14 Sep 2009 16:08:14 -0400 [thread overview]
Message-ID: <1252958896-25150-71-git-send-email-vapier@gentoo.org> (raw)
In-Reply-To: <1252958896-25150-1-git-send-email-vapier@gentoo.org>
From: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
arch/blackfin/mach-bf527/boards/cm_bf527.c | 97 ++++++++++++----------
arch/blackfin/mach-bf533/boards/cm_bf533.c | 114 ++++++++++++++++++++++++++-
arch/blackfin/mach-bf537/boards/tcm_bf537.c | 13 ++--
arch/blackfin/mach-bf548/boards/cm_bf548.c | 15 +++-
arch/blackfin/mach-bf561/boards/cm_bf561.c | 113 ++++++++++++++++++++++++++-
5 files changed, 297 insertions(+), 55 deletions(-)
diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index a0f623d..08a3f01 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -151,46 +151,6 @@ static struct platform_device musb_device = {
};
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
-static struct mtd_partition ezkit_partitions[] = {
- {
- .name = "bootloader(nor)",
- .size = 0x40000,
- .offset = 0,
- }, {
- .name = "linux kernel(nor)",
- .size = 0x1C0000,
- .offset = MTDPART_OFS_APPEND,
- }, {
- .name = "file system(nor)",
- .size = MTDPART_SIZ_FULL,
- .offset = MTDPART_OFS_APPEND,
- }
-};
-
-static struct physmap_flash_data ezkit_flash_data = {
- .width = 2,
- .parts = ezkit_partitions,
- .nr_parts = ARRAY_SIZE(ezkit_partitions),
-};
-
-static struct resource ezkit_flash_resource = {
- .start = 0x20000000,
- .end = 0x201fffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device ezkit_flash_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &ezkit_flash_data,
- },
- .num_resources = 1,
- .resource = &ezkit_flash_resource,
-};
-#endif
-
#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
static struct mtd_partition partition_info[] = {
{
@@ -662,6 +622,55 @@ static struct platform_device bfin_fb_adv7393_device = {
};
#endif
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+static struct mtd_partition cm_partitions[] = {
+ {
+ .name = "bootloader(nor)",
+ .size = 0x40000,
+ .offset = 0,
+ }, {
+ .name = "linux kernel(nor)",
+ .size = 0x100000,
+ .offset = MTDPART_OFS_APPEND,
+ }, {
+ .name = "file system(nor)",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+
+static struct physmap_flash_data cm_flash_data = {
+ .width = 2,
+ .parts = cm_partitions,
+ .nr_parts = ARRAY_SIZE(cm_partitions),
+};
+
+static unsigned cm_flash_gpios[] = { GPIO_PH9, GPIO_PG11 };
+
+static struct resource cm_flash_resource[] = {
+ {
+ .name = "cfi_probe",
+ .start = 0x20000000,
+ .end = 0x201fffff,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = (unsigned long)cm_flash_gpios,
+ .end = ARRAY_SIZE(cm_flash_gpios),
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct platform_device cm_flash_device = {
+ .name = "gpio-addr-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &cm_flash_data,
+ },
+ .num_resources = ARRAY_SIZE(cm_flash_resource),
+ .resource = cm_flash_resource,
+};
+#endif
+
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
static struct resource bfin_uart_resources[] = {
#ifdef CONFIG_SERIAL_BFIN_UART0
@@ -847,7 +856,7 @@ static struct platform_device bfin_dpmc = {
},
};
-static struct platform_device *stamp_devices[] __initdata = {
+static struct platform_device *cmbf527_devices[] __initdata = {
&bfin_dpmc,
@@ -930,8 +939,8 @@ static struct platform_device *stamp_devices[] __initdata = {
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
- &ezkit_flash_device,
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+ &cm_flash_device,
#endif
&bfin_gpios_device,
@@ -942,7 +951,7 @@ static int __init cm_init(void)
printk(KERN_INFO "%s(): registering device resources\n", __func__);
i2c_register_board_info(0, bfin_i2c_board_info,
ARRAY_SIZE(bfin_i2c_board_info));
- platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
+ platform_add_devices(cmbf527_devices, ARRAY_SIZE(cmbf527_devices));
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
return 0;
}
diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
index ef31bc5..7443b26 100644
--- a/arch/blackfin/mach-bf533/boards/cm_bf533.c
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -31,8 +31,10 @@
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
+#include <linux/spi/mmc_spi.h>
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
@@ -141,9 +143,9 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = 5,
+ .chip_select = 1,
.controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
@@ -225,6 +227,40 @@ static struct platform_device smc91x_device = {
};
#endif
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include <linux/smsc911x.h>
+
+static struct resource smsc911x_resources[] = {
+ {
+ .name = "smsc911x-memory",
+ .start = 0x20308000,
+ .end = 0x20308000 + 0xFF,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_PF8,
+ .end = IRQ_PF8,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
+ },
+};
+
+static struct smsc911x_platform_config smsc911x_config = {
+ .flags = SMSC911X_USE_16BIT,
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+ .phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
+static struct platform_device smsc911x_device = {
+ .name = "smsc911x",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(smsc911x_resources),
+ .resource = smsc911x_resources,
+ .dev = {
+ .platform_data = &smsc911x_config,
+ },
+};
+#endif
+
static struct resource bfin_gpios_resources = {
.start = 0,
.end = MAX_BLACKFIN_GPIOS - 1,
@@ -335,6 +371,68 @@ static struct platform_device isp1362_hcd_device = {
};
#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+ {
+ .start = 0x20300000,
+ .end = 0x20300000 + 0x100,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_PF6,
+ .end = IRQ_PF6,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct platform_device net2272_bfin_device = {
+ .name = "net2272",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(net2272_bfin_resources),
+ .resource = net2272_bfin_resources,
+};
+#endif
+
+
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+static struct mtd_partition para_partitions[] = {
+ {
+ .name = "bootloader(nor)",
+ .size = 0x40000,
+ .offset = 0,
+ }, {
+ .name = "linux+rootfs(nor)",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ },
+};
+
+static struct physmap_flash_data para_flash_data = {
+ .width = 2,
+ .parts = para_partitions,
+ .nr_parts = ARRAY_SIZE(para_partitions),
+};
+
+static struct resource para_flash_resource = {
+ .start = 0x20000000,
+ .end = 0x201fffff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device para_flash_device = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = ¶_flash_data,
+ },
+ .num_resources = 1,
+ .resource = ¶_flash_resource,
+};
+#endif
+
+
+
static const unsigned int cclk_vlev_datasheet[] =
{
VRPAIR(VLEV_085, 250000000),
@@ -393,10 +491,22 @@ static struct platform_device *cm_bf533_devices[] __initdata = {
&smc91x_device,
#endif
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+ &smsc911x_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+ &net2272_bfin_device,
+#endif
+
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
&bfin_spi0_device,
#endif
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+ ¶_flash_device,
+#endif
+
&bfin_gpios_device,
};
diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
index dc4f161..61353f7 100644
--- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
@@ -45,6 +45,7 @@
#include <asm/bfin5xx_spi.h>
#include <asm/portmux.h>
#include <asm/dpmc.h>
+#include <linux/spi/mmc_spi.h>
/*
* Name the Board for the /proc/cpuinfo
@@ -148,7 +149,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.modalias = "mmc_spi",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = 5,
+ .chip_select = 1,
.controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
@@ -279,12 +280,12 @@ static struct platform_device isp1362_hcd_device = {
#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
static struct resource net2272_bfin_resources[] = {
{
- .start = 0x20200000,
- .end = 0x20200000 + 0x100,
+ .start = 0x20300000,
+ .end = 0x20300000 + 0x100,
.flags = IORESOURCE_MEM,
}, {
- .start = IRQ_PH14,
- .end = IRQ_PH14,
+ .start = IRQ_PG13,
+ .end = IRQ_PG13,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
},
};
@@ -318,7 +319,7 @@ static struct mtd_partition cm_partitions[] = {
.offset = 0,
}, {
.name = "linux kernel(nor)",
- .size = 0xE0000,
+ .size = 0x100000,
.offset = MTDPART_OFS_APPEND,
}, {
.name = "file system(nor)",
diff --git a/arch/blackfin/mach-bf548/boards/cm_bf548.c b/arch/blackfin/mach-bf548/boards/cm_bf548.c
index 290b6e9..e565aae 100644
--- a/arch/blackfin/mach-bf548/boards/cm_bf548.c
+++ b/arch/blackfin/mach-bf548/boards/cm_bf548.c
@@ -291,6 +291,8 @@ static struct platform_device bfin_sir3_device = {
#endif
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include <linux/smsc911x.h>
+
static struct resource smsc911x_resources[] = {
{
.name = "smsc911x-memory",
@@ -304,11 +306,22 @@ static struct resource smsc911x_resources[] = {
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
},
};
+
+static struct smsc911x_platform_config smsc911x_config = {
+ .flags = SMSC911X_USE_16BIT,
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+ .phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
static struct platform_device smsc911x_device = {
.name = "smsc911x",
.id = 0,
.num_resources = ARRAY_SIZE(smsc911x_resources),
.resource = smsc911x_resources,
+ .dev = {
+ .platform_data = &smsc911x_config,
+ },
};
#endif
@@ -473,7 +486,7 @@ static struct mtd_partition para_partitions[] = {
.offset = 0,
}, {
.name = "linux kernel(nor)",
- .size = 0x400000,
+ .size = 0x100000,
.offset = MTDPART_OFS_APPEND,
}, {
.name = "file system(nor)",
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index 5721620..6577ecf 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -42,6 +42,7 @@
#include <asm/bfin5xx_spi.h>
#include <asm/portmux.h>
#include <asm/dpmc.h>
+#include <linux/mtd/physmap.h>
/*
* Name the Board for the /proc/cpuinfo
@@ -142,9 +143,9 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = 5,
+ .chip_select = 1,
.controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
@@ -228,6 +229,62 @@ static struct platform_device smc91x_device = {
};
#endif
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include <linux/smsc911x.h>
+
+static struct resource smsc911x_resources[] = {
+ {
+ .name = "smsc911x-memory",
+ .start = 0x24008000,
+ .end = 0x24008000 + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_PF43,
+ .end = IRQ_PF43,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
+ },
+};
+
+static struct smsc911x_platform_config smsc911x_config = {
+ .flags = SMSC911X_USE_16BIT,
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+ .phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
+static struct platform_device smsc911x_device = {
+ .name = "smsc911x",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(smsc911x_resources),
+ .resource = smsc911x_resources,
+ .dev = {
+ .platform_data = &smsc911x_config,
+ },
+};
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+ {
+ .start = 0x24000000,
+ .end = 0x24000000 + 0x100,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_PF45,
+ .end = IRQ_PF45,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct platform_device net2272_bfin_device = {
+ .name = "net2272",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(net2272_bfin_resources),
+ .resource = net2272_bfin_resources,
+};
+#endif
+
static struct resource bfin_gpios_resources = {
.start = 0,
.end = MAX_BLACKFIN_GPIOS - 1,
@@ -363,6 +420,46 @@ static struct platform_device bfin_pata_device = {
};
#endif
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+static struct mtd_partition para_partitions[] = {
+ {
+ .name = "bootloader(nor)",
+ .size = 0x40000,
+ .offset = 0,
+ }, {
+ .name = "linux kernel(nor)",
+ .size = 0x100000,
+ .offset = MTDPART_OFS_APPEND,
+ }, {
+ .name = "file system(nor)",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+
+static struct physmap_flash_data para_flash_data = {
+ .width = 2,
+ .parts = para_partitions,
+ .nr_parts = ARRAY_SIZE(para_partitions),
+};
+
+static struct resource para_flash_resource = {
+ .start = 0x20000000,
+ .end = 0x207fffff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device para_flash_device = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = ¶_flash_data,
+ },
+ .num_resources = 1,
+ .resource = ¶_flash_resource,
+};
+#endif
+
static const unsigned int cclk_vlev_datasheet[] =
{
VRPAIR(VLEV_085, 250000000),
@@ -416,6 +513,14 @@ static struct platform_device *cm_bf561_devices[] __initdata = {
&smc91x_device,
#endif
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+ &smsc911x_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+ &net2272_bfin_device,
+#endif
+
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
&bfin_spi0_device,
#endif
@@ -424,6 +529,10 @@ static struct platform_device *cm_bf561_devices[] __initdata = {
&bfin_pata_device,
#endif
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+ ¶_flash_device,
+#endif
+
&bfin_gpios_device,
};
--
1.6.4.2
next prev parent reply other threads:[~2009-09-14 20:11 UTC|newest]
Thread overview: 86+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-09-14 20:07 [PATCH 00/72] Blackfin updates for 2.6.32 Mike Frysinger
2009-09-14 20:07 ` [PATCH 01/72] Blackfin: bf537-stamp: update ADP5588 header name Mike Frysinger
2009-09-14 20:07 ` [PATCH 02/72] Blackfin: bf537-stamp: declare SPI IRQ resources Mike Frysinger
2009-09-14 20:07 ` [PATCH 03/72] Blackfin: bf537-stamp: add resources for AD1938 audio card Mike Frysinger
2009-09-14 20:07 ` [PATCH 04/72] Blackfin: make EVT3->EVT5 lowering more robust wrt IPEND[4] Mike Frysinger
2009-09-14 20:07 ` [PATCH 05/72] Blackfin: checkpatch --file arch/blackfin/kernel/ipipe.c Mike Frysinger
2009-09-14 20:07 ` [PATCH 06/72] Blackfin: fix misnomer of some I-pipe helpers Mike Frysinger
2009-09-14 20:07 ` [PATCH 07/72] Blackfin: export show_stack() to modules Mike Frysinger
2009-09-14 20:07 ` [PATCH 08/72] Blackfin: allow high priority domains to preempt schedule_tail() Mike Frysinger
2009-09-14 20:07 ` [PATCH 09/72] Blackfin: use generic name for EVT14 handler Mike Frysinger
2009-09-14 20:07 ` [PATCH 10/72] Blackfin: reuse evt_evt14 handler to perform irqtail epilogue Mike Frysinger
2009-09-14 20:07 ` [PATCH 11/72] Blackfin: allow EVT5 to preempt irqtail prologue (CONFIG_DEBUG_HWERR) Mike Frysinger
2009-09-14 20:07 ` [PATCH 12/72] Blackfin: document __ipipe_call_irqtail Mike Frysinger
2009-09-14 20:07 ` [PATCH 13/72] Blackfin: sanitize manual control of IPEND[4] Mike Frysinger
2009-09-14 20:07 ` [PATCH 14/72] Blackfin: inline I-pipe bypass code in ret_from_exception Mike Frysinger
2009-09-14 20:07 ` [PATCH 15/72] Blackfin: cleanup traps decode_address() a bit Mike Frysinger
2009-09-14 20:07 ` [PATCH 16/72] Blackfin: convert ptrace to new memory functions Mike Frysinger
2009-09-14 20:07 ` [PATCH 17/72] Blackfin: reject outdated/unused/wrong relocation types Mike Frysinger
2009-09-14 20:07 ` [PATCH 18/72] Blackfin: cleanup printk() usage in module code Mike Frysinger
2009-09-14 20:07 ` [PATCH 19/72] Blackfin: convert malloc()/memset() to zalloc() " Mike Frysinger
2009-09-14 20:07 ` [PATCH 20/72] Blackfin: cleanup module section checking Mike Frysinger
2009-09-14 20:07 ` [PATCH 21/72] Blackfin: fix module reloc handling for all memory regions Mike Frysinger
2009-09-14 20:07 ` [PATCH 22/72] Blackfin: clean up early memory setup code Mike Frysinger
2009-09-14 20:07 ` [PATCH 23/72] Blackfin: rename PCF8574 driver config Mike Frysinger
2009-09-14 20:07 ` [PATCH 24/72] Blackfin: unify duplicated SMP checks in L2 cache kconfig Mike Frysinger
2009-09-14 20:07 ` [PATCH 25/72] Blackfin: push SRAM locks down into related ifdefs Mike Frysinger
2009-09-14 20:07 ` [PATCH 26/72] Blackfin: add support for common FDPIC ptrace requests Mike Frysinger
2009-09-14 20:07 ` [PATCH 27/72] Blackfin: add an early shadow console Mike Frysinger
2009-09-14 20:07 ` [PATCH 28/72] Blackfin: catch hardware errors earlier during booting Mike Frysinger
2009-09-14 20:07 ` [PATCH 29/72] Blackfin: fix BF548 UART0 DMA IRQ translation Mike Frysinger
2009-09-14 20:07 ` [PATCH 30/72] Blackfin: bf538: add bfin_clear_PPI_STATUS() helper Mike Frysinger
2009-09-14 20:07 ` [PATCH 31/72] Blackfin: bf533-stamp: add resources for mmc_spi card Mike Frysinger
2009-09-14 20:07 ` [PATCH 32/72] Blackfin: do not try displaying the end of the stack Mike Frysinger
2009-09-14 20:07 ` [PATCH 33/72] Blackfin: bf537-stamp: update AD714x resources Mike Frysinger
2009-09-14 20:07 ` [PATCH 34/72] Blackfin: clean up duplicate I2C device type definitions Mike Frysinger
2009-09-14 20:07 ` [PATCH 35/72] Blackfin: fix MPU handling of invalid memory accesses Mike Frysinger
2009-09-14 20:07 ` [PATCH 36/72] Blackfin: bf533-stamp: fix typo in SPI frequency for ad1836 codec Mike Frysinger
2009-09-14 20:07 ` [PATCH 37/72] Blackfin: improve double fault debug handling Mike Frysinger
2009-09-14 20:07 ` [PATCH 38/72] Blackfin: bf537-stamp: drop ATA interrupt probe workaround Mike Frysinger
2009-09-14 20:07 ` [PATCH 39/72] Blackfin: convert boards to use platform data with smc91x Mike Frysinger
2009-09-14 20:07 ` [PATCH 40/72] Blackfin: drop unused MMR defines that only cause bad code to be written Mike Frysinger
2009-09-14 20:07 ` [PATCH 41/72] Blackfin: cm-bf527/bf537-stamp: fix dm9000 resources Mike Frysinger
2009-09-14 20:07 ` [PATCH 42/72] Blackfin: bf548-ezkit: fix incorrect LCD size parameters Mike Frysinger
2009-09-14 20:07 ` [PATCH 43/72] Blackfin: fix read buffer overflow Mike Frysinger
2009-09-14 20:07 ` [PATCH 44/72] Blackfin: bf538-ezkit: add resources for parallel flash Mike Frysinger
2009-09-14 20:07 ` [PATCH 45/72] Blackfin: update anomaly lists Mike Frysinger
2009-09-14 20:07 ` [PATCH 46/72] Blackfin: bf537-stamp: update ad1836 resources Mike Frysinger
2009-09-14 20:07 ` [PATCH 47/72] Blackfin: cleanup sync handling when enabling/disabling cplbs Mike Frysinger
2009-09-14 20:07 ` [PATCH 48/72] Blackfin: SMP port does not yet support cpu frequency scaling Mike Frysinger
2009-09-14 20:07 ` [PATCH 49/72] Blackfin: fix BF522/BF523 max VCO mixup Mike Frysinger
2009-09-14 20:07 ` [PATCH 50/72] Blackfin: do not trace the exception handler Mike Frysinger
2009-09-14 20:07 ` [PATCH 51/72] Blackfin: drop board resources for dead devices (pbx/ad9960) Mike Frysinger
2009-09-14 20:07 ` [PATCH 52/72] Blackfin: punt dead cache locking code Mike Frysinger
2009-09-14 20:07 ` [PATCH 53/72] Blackfin: delete '-spi' suffix in ad1836/ad1938 driver name Mike Frysinger
2009-09-14 20:07 ` [PATCH 54/72] Blackfin: optimize fixed code handling for the most common case Mike Frysinger
2009-09-14 20:07 ` [PATCH 55/72] Blackfin: handle the core timer interrupt with handle_percpu_irq on SMP Mike Frysinger
2009-09-14 20:08 ` [PATCH 56/72] Blackfin: Fix link errors with binutils 2.19 and GCC 4.3 Mike Frysinger
2009-09-14 20:08 ` [PATCH 57/72] Blackfin: remove useless duplicated assignment in gpio code Mike Frysinger
2009-09-14 20:08 ` [PATCH 58/72] Blackfin: use raw_smp_processor_id() in exception code Mike Frysinger
2009-09-14 20:08 ` [PATCH 59/72] Blackfin: fix spelling in a few comments Mike Frysinger
2009-09-14 20:08 ` [PATCH 60/72] Blackfin: workaround anomaly 05000283 Mike Frysinger
2009-09-14 20:08 ` [PATCH 61/72] Blackfin: add some isram-driver self tests Mike Frysinger
2009-09-14 20:08 ` [PATCH 62/72] Blackfin: bf537-stamp: add adp5588 gpio resources Mike Frysinger
2009-09-14 20:08 ` [PATCH 63/72] Blackfin: fix typo in isram_write() Mike Frysinger
2009-09-14 20:08 ` [PATCH 64/72] Blackfin: fix BF54x SPI CS resources Mike Frysinger
2009-09-14 20:08 ` [PATCH 65/72] Blackfin: use KERN_ALERT in all kgdb_test output Mike Frysinger
2009-09-14 20:08 ` [PATCH 66/72] Blackfin: add ICPLB coverage for async banks Mike Frysinger
2009-09-14 20:08 ` [PATCH 67/72] Blackfin: increase default async timings for parallel flashes Mike Frysinger
2009-09-14 20:08 ` [PATCH 68/72] Blackfin: bf538-ezkit: add SPI IRQ resources Mike Frysinger
2009-09-14 20:08 ` [PATCH 69/72] Blackfin: cm-bf537u: split board from cm-bf537e Mike Frysinger
2009-09-14 20:08 ` Mike Frysinger [this message]
2009-09-14 20:08 ` [PATCH 71/72] Blackfin: update ftrace_push_return_trace() breakage Mike Frysinger
2009-09-14 20:08 ` [PATCH 72/72] Blackfin: swap clocksource ratings for gptimer/cycles Mike Frysinger
2009-09-14 20:50 ` [PATCH 00/72] Blackfin updates for 2.6.32 Daniel Walker
2009-09-14 20:57 ` Mike Frysinger
2009-09-14 21:04 ` Daniel Walker
2009-09-14 21:07 ` Mike Frysinger
2009-09-14 21:21 ` Daniel Walker
2009-09-14 22:17 ` Mike Frysinger
2009-09-14 22:36 ` Daniel Walker
2009-09-16 2:54 ` Mike Frysinger
2009-09-16 2:56 ` Mike Frysinger
2009-09-16 3:06 ` Daniel Walker
2009-09-16 3:21 ` Mike Frysinger
2009-09-16 3:59 ` Daniel Walker
2009-09-16 4:13 ` Mike Frysinger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1252958896-25150-71-git-send-email-vapier@gentoo.org \
--to=vapier@gentoo.org \
--cc=Harald.Krapfenbauer@bluetechnix.at \
--cc=linux-kernel@vger.kernel.org \
--cc=uclinux-dist-devel@blackfin.uclinux.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®