[PATCH v2 0/3] drm/msm: add RGB101010 pixel format and fix 10-bit DSC timing

[PATCH v2 0/3] drm/msm: add RGB101010 pixel format and fix 10-bit DSC timing

[Alexander Koskovich]

This series adds support for the RGB101010 (30bpp) pixel format and
fixes a DSC timing bug exposed by non 8 bit panels.

Tested on the BOE BF068MWM-TD0 panel (10 bit DSC) on the Nothing
Phone (3a).

Note, I'd appreciate a comment on the INTF timing change from someone
at QCOM who knows the DPU hardware a bit better, this appears to be
what downstream is doing regardless of bpp, but let me know if there's
a better solution here.

Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
---
Changes in v2:
- Only allow RGB101010 if MSM_DSI_6G_VER >= V2.1.0
- Link to v1: https://lore.kernel.org/r/20260318-dsi-rgb101010-support-v1-0-6021eb79e796@pm.me

---
Alexander Koskovich (3):
      drm/mipi-dsi: add RGB101010 pixel format
      drm/msm/dsi: Add support for RGB101010 pixel format
      drm/msm/dpu: fix video mode DSC INTF timing width for non 8 bit panels

 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 12 +++++++-----
 drivers/gpu/drm/msm/dsi/dsi_cfg.c                    |  8 ++++++++
 drivers/gpu/drm/msm/dsi/dsi_cfg.h                    |  1 +
 drivers/gpu/drm/msm/dsi/dsi_host.c                   |  9 +++++++++
 drivers/gpu/drm/msm/registers/display/dsi.xml        |  5 ++++-
 include/drm/drm_mipi_dsi.h                           |  4 ++++
 6 files changed, 33 insertions(+), 6 deletions(-)
---
base-commit: f338e77383789c0cae23ca3d48adcc5e9e137e3c
change-id: 20260318-dsi-rgb101010-support-4956b1cd8657

Best regards,
-- 
Alexander Koskovich <akoskovich@pm.me>

[PATCH v2 1/3] drm/mipi-dsi: add RGB101010 pixel format

[Alexander Koskovich]

Add MIPI_DSI_FMT_RGB101010 for 30 bit (10,10,10 RGB) pixel format,
corresponding to the packed 30 bit pixel stream defined in MIPI DSI
v1.3 Section 8.8.17.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
---
 include/drm/drm_mipi_dsi.h | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/include/drm/drm_mipi_dsi.h b/include/drm/drm_mipi_dsi.h
index 3aba7b380c8d..a822e9e876af 100644
--- a/include/drm/drm_mipi_dsi.h
+++ b/include/drm/drm_mipi_dsi.h
@@ -140,6 +140,7 @@ struct mipi_dsi_host *of_find_mipi_dsi_host_by_node(struct device_node *node);
 #define MIPI_DSI_HS_PKT_END_ALIGNED	BIT(12)
 
 enum mipi_dsi_pixel_format {
+	MIPI_DSI_FMT_RGB101010,
 	MIPI_DSI_FMT_RGB888,
 	MIPI_DSI_FMT_RGB666,
 	MIPI_DSI_FMT_RGB666_PACKED,
@@ -235,6 +236,9 @@ extern const struct bus_type mipi_dsi_bus_type;
 static inline int mipi_dsi_pixel_format_to_bpp(enum mipi_dsi_pixel_format fmt)
 {
 	switch (fmt) {
+	case MIPI_DSI_FMT_RGB101010:
+		return 30;
+
 	case MIPI_DSI_FMT_RGB888:
 	case MIPI_DSI_FMT_RGB666:
 		return 24;

-- 
2.53.0

[PATCH v2 2/3] drm/msm/dsi: Add support for RGB101010 pixel format

[Alexander Koskovich]

Add video and command mode destination format mappings for RGB101010,
and extend the VID_CFG0 DST_FORMAT bitfield to 3 bits to accommodate
the new format value.

Make sure this is guarded behind MSM_DSI_6G_VER >= V2.1.0 as anything
older does not support this.

Required for 10 bit panels such as the BOE BF068MWM-TD0.

Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
---
 drivers/gpu/drm/msm/dsi/dsi_cfg.c             | 8 ++++++++
 drivers/gpu/drm/msm/dsi/dsi_cfg.h             | 1 +
 drivers/gpu/drm/msm/dsi/dsi_host.c            | 9 +++++++++
 drivers/gpu/drm/msm/registers/display/dsi.xml | 5 ++++-
 4 files changed, 22 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/msm/dsi/dsi_cfg.c b/drivers/gpu/drm/msm/dsi/dsi_cfg.c
index bd3c51c350e7..6a7ea2183a3b 100644
--- a/drivers/gpu/drm/msm/dsi/dsi_cfg.c
+++ b/drivers/gpu/drm/msm/dsi/dsi_cfg.c
@@ -133,6 +133,7 @@ static const struct msm_dsi_config msm8998_dsi_cfg = {
 	.io_start = {
 		{ 0xc994000, 0xc996000 },
 	},
+	.has_rgb30 = true,
 };
 
 static const char * const dsi_sdm660_bus_clk_names[] = {
@@ -152,6 +153,7 @@ static const struct msm_dsi_config sdm660_dsi_cfg = {
 	.io_start = {
 		{ 0xc994000, 0xc996000 },
 	},
+	.has_rgb30 = true,
 };
 
 static const char * const dsi_v2_4_clk_names[] = {
@@ -173,6 +175,7 @@ static const struct msm_dsi_config sdm845_dsi_cfg = {
 		{ 0xae94000, 0xae96000 }, /* SDM845 / SDM670 */
 		{ 0x5e94000 }, /* QCM2290 / SM6115 / SM6125 / SM6375 */
 	},
+	.has_rgb30 = true,
 };
 
 static const struct regulator_bulk_data sm8550_dsi_regulators[] = {
@@ -188,6 +191,7 @@ static const struct msm_dsi_config sm8550_dsi_cfg = {
 	.io_start = {
 		{ 0xae94000, 0xae96000 },
 	},
+	.has_rgb30 = true,
 };
 
 static const struct regulator_bulk_data sm8650_dsi_regulators[] = {
@@ -203,6 +207,7 @@ static const struct msm_dsi_config sm8650_dsi_cfg = {
 	.io_start = {
 		{ 0xae94000, 0xae96000 },
 	},
+	.has_rgb30 = true,
 };
 
 static const struct msm_dsi_config kaanapali_dsi_cfg = {
@@ -214,6 +219,7 @@ static const struct msm_dsi_config kaanapali_dsi_cfg = {
 	.io_start = {
 		{ 0x9ac0000, 0x9ac3000 },
 	},
+	.has_rgb30 = true,
 };
 
 static const struct regulator_bulk_data sc7280_dsi_regulators[] = {
@@ -230,6 +236,7 @@ static const struct msm_dsi_config sc7280_dsi_cfg = {
 	.io_start = {
 		{ 0xae94000, 0xae96000 },
 	},
+	.has_rgb30 = true,
 };
 
 static const struct regulator_bulk_data sa8775p_dsi_regulators[] = {
@@ -246,6 +253,7 @@ static const struct msm_dsi_config sa8775p_dsi_cfg = {
 	.io_start = {
 		{ 0xae94000, 0xae96000 },
 	},
+	.has_rgb30 = true,
 };
 
 static const struct msm_dsi_host_cfg_ops msm_dsi_v2_host_ops = {
diff --git a/drivers/gpu/drm/msm/dsi/dsi_cfg.h b/drivers/gpu/drm/msm/dsi/dsi_cfg.h
index 5dc812028bd5..15cb9b46fadf 100644
--- a/drivers/gpu/drm/msm/dsi/dsi_cfg.h
+++ b/drivers/gpu/drm/msm/dsi/dsi_cfg.h
@@ -48,6 +48,7 @@ struct msm_dsi_config {
 	const char * const *bus_clk_names;
 	const int num_bus_clks;
 	const resource_size_t io_start[VARIANTS_MAX][DSI_MAX];
+	bool has_rgb30;
 };
 
 struct msm_dsi_host_cfg_ops {
diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c
index db6da99375a1..34fd0dc5f7c7 100644
--- a/drivers/gpu/drm/msm/dsi/dsi_host.c
+++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
@@ -757,6 +757,7 @@ static inline enum dsi_vid_dst_format
 dsi_get_vid_fmt(const enum mipi_dsi_pixel_format mipi_fmt)
 {
 	switch (mipi_fmt) {
+	case MIPI_DSI_FMT_RGB101010:	return VID_DST_FORMAT_RGB101010;
 	case MIPI_DSI_FMT_RGB888:	return VID_DST_FORMAT_RGB888;
 	case MIPI_DSI_FMT_RGB666:	return VID_DST_FORMAT_RGB666_LOOSE;
 	case MIPI_DSI_FMT_RGB666_PACKED:	return VID_DST_FORMAT_RGB666;
@@ -769,6 +770,7 @@ static inline enum dsi_cmd_dst_format
 dsi_get_cmd_fmt(const enum mipi_dsi_pixel_format mipi_fmt)
 {
 	switch (mipi_fmt) {
+	case MIPI_DSI_FMT_RGB101010:	return CMD_DST_FORMAT_RGB101010;
 	case MIPI_DSI_FMT_RGB888:	return CMD_DST_FORMAT_RGB888;
 	case MIPI_DSI_FMT_RGB666_PACKED:
 	case MIPI_DSI_FMT_RGB666:	return CMD_DST_FORMAT_RGB666;
@@ -1698,6 +1700,13 @@ static int dsi_host_attach(struct mipi_dsi_host *host,
 	if (dsi->lanes > msm_host->num_data_lanes)
 		return -EINVAL;
 
+	if (dsi->format == MIPI_DSI_FMT_RGB101010 &&
+	    !msm_host->cfg_hnd->cfg->has_rgb30) {
+		DRM_DEV_ERROR(&msm_host->pdev->dev,
+			      "RGB101010 not supported on this DSI controller\n");
+		return -EINVAL;
+	}
+
 	msm_host->channel = dsi->channel;
 	msm_host->lanes = dsi->lanes;
 	msm_host->format = dsi->format;
diff --git a/drivers/gpu/drm/msm/registers/display/dsi.xml b/drivers/gpu/drm/msm/registers/display/dsi.xml
index c7a7b633d747..e40125f75175 100644
--- a/drivers/gpu/drm/msm/registers/display/dsi.xml
+++ b/drivers/gpu/drm/msm/registers/display/dsi.xml
@@ -15,6 +15,7 @@ xsi:schemaLocation="https://gitlab.freedesktop.org/freedreno/ rules-fd.xsd">
 		<value name="VID_DST_FORMAT_RGB666" value="1"/>
 		<value name="VID_DST_FORMAT_RGB666_LOOSE" value="2"/>
 		<value name="VID_DST_FORMAT_RGB888" value="3"/>
+		<value name="VID_DST_FORMAT_RGB101010" value="4"/>
 	</enum>
 	<enum name="dsi_rgb_swap">
 		<value name="SWAP_RGB" value="0"/>
@@ -39,6 +40,7 @@ xsi:schemaLocation="https://gitlab.freedesktop.org/freedreno/ rules-fd.xsd">
 		<value name="CMD_DST_FORMAT_RGB565" value="6"/>
 		<value name="CMD_DST_FORMAT_RGB666" value="7"/>
 		<value name="CMD_DST_FORMAT_RGB888" value="8"/>
+		<value name="CMD_DST_FORMAT_RGB101010" value="9"/>
 	</enum>
 	<enum name="dsi_lane_swap">
 		<value name="LANE_SWAP_0123" value="0"/>
@@ -142,7 +144,8 @@ xsi:schemaLocation="https://gitlab.freedesktop.org/freedreno/ rules-fd.xsd">
 	</reg32>
 	<reg32 offset="0x0000c" name="VID_CFG0">
 		<bitfield name="VIRT_CHANNEL" low="0" high="1" type="uint"/>  <!-- always zero? -->
-		<bitfield name="DST_FORMAT" low="4" high="5" type="dsi_vid_dst_format"/>
+		<!-- high was 5 before DSI 6G 2.1.0 -->
+		<bitfield name="DST_FORMAT" low="4" high="6" type="dsi_vid_dst_format"/>
 		<bitfield name="TRAFFIC_MODE" low="8" high="9" type="dsi_traffic_mode"/>
 		<bitfield name="BLLP_POWER_STOP" pos="12" type="boolean"/>
 		<bitfield name="EOF_BLLP_POWER_STOP" pos="15" type="boolean"/>

-- 
2.53.0

[PATCH v2 3/3] drm/msm/dpu: fix video mode DSC INTF timing width for non 8 bit panels

[Alexander Koskovich]

Using bits_per_component * 3 as the divisor for the compressed INTF
timing width produces constant FIFO errors for panels such as the BOE
BF068MWM-TD0 which is a 10 bit panel.

The downstream driver calculates the compressed timing width by
dividing the total compressed bytes per line by 3 which does not depend
on bits_per_component. Switch the divisor to 24 to match downstream.

Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
---
 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
index 0ba777bda253..9b046a0e77aa 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
@@ -122,19 +122,21 @@ static void drm_mode_to_intf_timing_params(
 	}
 
 	/*
-	 * for DSI, if compression is enabled, then divide the horizonal active
-	 * timing parameters by compression ratio. bits of 3 components(R/G/B)
-	 * is compressed into bits of 1 pixel.
+	 * For DSI, if DSC is enabled, use a fixed divisor of 24 rather than
+	 * bits_per_component * 3 when calculating the compressed timing width.
+	 *
+	 * This matches the downstream driver and is required for panels with
+	 * bits_per_component != 8.
 	 */
 	if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) {
 		struct drm_dsc_config *dsc =
 		       dpu_encoder_get_dsc_config(phys_enc->parent);
+
 		/*
 		 * TODO: replace drm_dsc_get_bpp_int with logic to handle
 		 * fractional part if there is fraction
 		 */
-		timing->width = timing->width * drm_dsc_get_bpp_int(dsc) /
-				(dsc->bits_per_component * 3);
+		timing->width = timing->width * drm_dsc_get_bpp_int(dsc) / 24;
 		timing->xres = timing->width;
 	}
 }

-- 
2.53.0

Re: [PATCH v2 2/3] drm/msm/dsi: Add support for RGB101010 pixel format

[Dmitry Baryshkov]

On Thu, Mar 19, 2026 at 04:00:05AM +0000, Alexander Koskovich wrote:
> Add video and command mode destination format mappings for RGB101010,
> and extend the VID_CFG0 DST_FORMAT bitfield to 3 bits to accommodate
> the new format value.
> 
> Make sure this is guarded behind MSM_DSI_6G_VER >= V2.1.0 as anything
> older does not support this.
> 
> Required for 10 bit panels such as the BOE BF068MWM-TD0.
> 
> Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
> ---
>  drivers/gpu/drm/msm/dsi/dsi_cfg.c             | 8 ++++++++
>  drivers/gpu/drm/msm/dsi/dsi_cfg.h             | 1 +
>  drivers/gpu/drm/msm/dsi/dsi_host.c            | 9 +++++++++
>  drivers/gpu/drm/msm/registers/display/dsi.xml | 5 ++++-
>  4 files changed, 22 insertions(+), 1 deletion(-)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

Re: [PATCH v2 3/3] drm/msm/dpu: fix video mode DSC INTF timing width for non 8 bit panels

[Neil Armstrong]

On 3/19/26 05:00, Alexander Koskovich wrote:
> Using bits_per_component * 3 as the divisor for the compressed INTF
> timing width produces constant FIFO errors for panels such as the BOE
> BF068MWM-TD0 which is a 10 bit panel.
> 
> The downstream driver calculates the compressed timing width by
> dividing the total compressed bytes per line by 3 which does not depend
> on bits_per_component. Switch the divisor to 24 to match downstream.
> 
> Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
> ---
>   drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 12 +++++++-----
>   1 file changed, 7 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> index 0ba777bda253..9b046a0e77aa 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> @@ -122,19 +122,21 @@ static void drm_mode_to_intf_timing_params(
>   	}
>   
>   	/*
> -	 * for DSI, if compression is enabled, then divide the horizonal active
> -	 * timing parameters by compression ratio. bits of 3 components(R/G/B)
> -	 * is compressed into bits of 1 pixel.
> +	 * For DSI, if DSC is enabled, use a fixed divisor of 24 rather than
> +	 * bits_per_component * 3 when calculating the compressed timing width.
> +	 *
> +	 * This matches the downstream driver and is required for panels with
> +	 * bits_per_component != 8.
>   	 */
>   	if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) {
>   		struct drm_dsc_config *dsc =
>   		       dpu_encoder_get_dsc_config(phys_enc->parent);
> +
>   		/*
>   		 * TODO: replace drm_dsc_get_bpp_int with logic to handle
>   		 * fractional part if there is fraction
>   		 */
> -		timing->width = timing->width * drm_dsc_get_bpp_int(dsc) /
> -				(dsc->bits_per_component * 3);
> +		timing->width = timing->width * drm_dsc_get_bpp_int(dsc) / 24;



@bits_per_component: Bits per component to code (8/10/12) <= how the DSC pixels are encoded in the stream
@bits_per_pixel: Target bits per pixel with 4 fractional bits, bits_per_pixel << 4 <= the target display pixels

- bits_per_component is the transport width
- bits_per_pixel is the display width
- 3 is the DSC compression ratio

So for a RGB101010 DSC display bits_per_pixel should be 10 << 4

But here you say bits_per_component should be 8 ? can you share the downstream config of your panel ?

Are you sure about the bits_per_component & bits_per_pixel values you set in the dsc parameters ?

Neil


>   		timing->xres = timing->width;
>   	}
>   }
> 

Re: [PATCH v2 3/3] drm/msm/dpu: fix video mode DSC INTF timing width for non 8 bit panels

[Alexander Koskovich]

On Thursday, March 19th, 2026 at 4:35 AM, Neil Armstrong <neil.armstrong@linaro.org> wrote:

> On 3/19/26 05:00, Alexander Koskovich wrote:
> > Using bits_per_component * 3 as the divisor for the compressed INTF
> > timing width produces constant FIFO errors for panels such as the BOE
> > BF068MWM-TD0 which is a 10 bit panel.
> >
> > The downstream driver calculates the compressed timing width by
> > dividing the total compressed bytes per line by 3 which does not depend
> > on bits_per_component. Switch the divisor to 24 to match downstream.
> >
> > Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
> > ---
> >   drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 12 +++++++-----
> >   1 file changed, 7 insertions(+), 5 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> > index 0ba777bda253..9b046a0e77aa 100644
> > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> > @@ -122,19 +122,21 @@ static void drm_mode_to_intf_timing_params(
> >   	}
> >
> >   	/*
> > -	 * for DSI, if compression is enabled, then divide the horizonal active
> > -	 * timing parameters by compression ratio. bits of 3 components(R/G/B)
> > -	 * is compressed into bits of 1 pixel.
> > +	 * For DSI, if DSC is enabled, use a fixed divisor of 24 rather than
> > +	 * bits_per_component * 3 when calculating the compressed timing width.
> > +	 *
> > +	 * This matches the downstream driver and is required for panels with
> > +	 * bits_per_component != 8.
> >   	 */
> >   	if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) {
> >   		struct drm_dsc_config *dsc =
> >   		       dpu_encoder_get_dsc_config(phys_enc->parent);
> > +
> >   		/*
> >   		 * TODO: replace drm_dsc_get_bpp_int with logic to handle
> >   		 * fractional part if there is fraction
> >   		 */
> > -		timing->width = timing->width * drm_dsc_get_bpp_int(dsc) /
> > -				(dsc->bits_per_component * 3);
> > +		timing->width = timing->width * drm_dsc_get_bpp_int(dsc) / 24;
> 
> 
> 
> @bits_per_component: Bits per component to code (8/10/12) <= how the DSC pixels are encoded in the stream
> @bits_per_pixel: Target bits per pixel with 4 fractional bits, bits_per_pixel << 4 <= the target display pixels
> 
> - bits_per_component is the transport width
> - bits_per_pixel is the display width
> - 3 is the DSC compression ratio
> 
> So for a RGB101010 DSC display bits_per_pixel should be 10 << 4
> 
> But here you say bits_per_component should be 8 ? can you share the downstream config of your panel ?

This is what is defined downstream for this panel, they're using 8:
https://github.com/NothingOSS/android_kernel_msm-6.1_nothing_sm7635/blob/sm7635/b/mr/vendor/qcom/proprietary/display-devicetree/display/dsi-panel-rm69220-dsc-fhd-plus-120hz-vid-boe.dtsi

> 
> Are you sure about the bits_per_component & bits_per_pixel values you set in the dsc parameters ?

I'm pretty sure they're correct, here's the panel driver I have atm:
https://github.com/AKoskovich/linux/blob/asteroids-6.19.y/drivers/gpu/drm/panel/panel-boe-bf068mwm-td0.c

> 
> Neil
> 
> 
> >   		timing->xres = timing->width;
> >   	}
> >   }
> >
> 
> 

Thanks,
Alex

Re: [PATCH v2 2/3] drm/msm/dsi: Add support for RGB101010 pixel format

[Konrad Dybcio]

On 3/19/26 5:00 AM, Alexander Koskovich wrote:
> Add video and command mode destination format mappings for RGB101010,
> and extend the VID_CFG0 DST_FORMAT bitfield to 3 bits to accommodate
> the new format value.
> 
> Make sure this is guarded behind MSM_DSI_6G_VER >= V2.1.0 as anything
> older does not support this.
> 
> Required for 10 bit panels such as the BOE BF068MWM-TD0.
> 
> Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
> ---
>  drivers/gpu/drm/msm/dsi/dsi_cfg.c             | 8 ++++++++
>  drivers/gpu/drm/msm/dsi/dsi_cfg.h             | 1 +
>  drivers/gpu/drm/msm/dsi/dsi_host.c            | 9 +++++++++
>  drivers/gpu/drm/msm/registers/display/dsi.xml | 5 ++++-
>  4 files changed, 22 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/gpu/drm/msm/dsi/dsi_cfg.c b/drivers/gpu/drm/msm/dsi/dsi_cfg.c
> index bd3c51c350e7..6a7ea2183a3b 100644
> --- a/drivers/gpu/drm/msm/dsi/dsi_cfg.c
> +++ b/drivers/gpu/drm/msm/dsi/dsi_cfg.c
> @@ -133,6 +133,7 @@ static const struct msm_dsi_config msm8998_dsi_cfg = {
>  	.io_start = {
>  		{ 0xc994000, 0xc996000 },
>  	},
> +	.has_rgb30 = true,

I wrote a patch to determine this at runtime, and only after I was done, I
noticed that we can already achieve this:

bool msm_dsi_host_is_wide_bus_enabled(struct mipi_dsi_host *host)
{
	struct msm_dsi_host *msm_host = to_msm_dsi_host(host);

	return msm_host->dsc &&
		(msm_host->cfg_hnd->major == MSM_DSI_VER_MAJOR_6G &&
		 msm_host->cfg_hnd->minor >= MSM_DSI_6G_VER_MINOR_V2_5_0);
}

let's perhaps extract this to a msm_dsi_host_version_is_gt(u32 major, u32 minor)
or similar

and your assumption about >=v2.1 is corroborated by a doc I have

Konrad

Re: [PATCH v2 2/3] drm/msm/dsi: Add support for RGB101010 pixel format

[Alexander Koskovich]

On Thursday, March 19th, 2026 at 5:10 AM, Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> wrote:

> On 3/19/26 5:00 AM, Alexander Koskovich wrote:
> > Add video and command mode destination format mappings for RGB101010,
> > and extend the VID_CFG0 DST_FORMAT bitfield to 3 bits to accommodate
> > the new format value.
> >
> > Make sure this is guarded behind MSM_DSI_6G_VER >= V2.1.0 as anything
> > older does not support this.
> >
> > Required for 10 bit panels such as the BOE BF068MWM-TD0.
> >
> > Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
> > ---
> >  drivers/gpu/drm/msm/dsi/dsi_cfg.c             | 8 ++++++++
> >  drivers/gpu/drm/msm/dsi/dsi_cfg.h             | 1 +
> >  drivers/gpu/drm/msm/dsi/dsi_host.c            | 9 +++++++++
> >  drivers/gpu/drm/msm/registers/display/dsi.xml | 5 ++++-
> >  4 files changed, 22 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/gpu/drm/msm/dsi/dsi_cfg.c b/drivers/gpu/drm/msm/dsi/dsi_cfg.c
> > index bd3c51c350e7..6a7ea2183a3b 100644
> > --- a/drivers/gpu/drm/msm/dsi/dsi_cfg.c
> > +++ b/drivers/gpu/drm/msm/dsi/dsi_cfg.c
> > @@ -133,6 +133,7 @@ static const struct msm_dsi_config msm8998_dsi_cfg = {
> >  	.io_start = {
> >  		{ 0xc994000, 0xc996000 },
> >  	},
> > +	.has_rgb30 = true,
> 
> I wrote a patch to determine this at runtime, and only after I was done, I
> noticed that we can already achieve this:
> 
> bool msm_dsi_host_is_wide_bus_enabled(struct mipi_dsi_host *host)
> {
> 	struct msm_dsi_host *msm_host = to_msm_dsi_host(host);
> 
> 	return msm_host->dsc &&
> 		(msm_host->cfg_hnd->major == MSM_DSI_VER_MAJOR_6G &&
> 		 msm_host->cfg_hnd->minor >= MSM_DSI_6G_VER_MINOR_V2_5_0);
> }
> 
> let's perhaps extract this to a msm_dsi_host_version_is_gt(u32 major, u32 minor)
> or similar

That's what I was looking into initially, but V2_2_0 (0x20000000) is numerically less than V2_1_0 (0x20010000) so didn't think I could do that.

Do you know if msm8998 is correct? Downstream says it is 2.0 not 2.2. 

> 
> and your assumption about >=v2.1 is corroborated by a doc I have
> 
> Konrad
> 

Thanks,
Alex

Re: [PATCH v2 2/3] drm/msm/dsi: Add support for RGB101010 pixel format

[Konrad Dybcio]

On 3/19/26 10:25 AM, Alexander Koskovich wrote:
> On Thursday, March 19th, 2026 at 5:10 AM, Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> wrote:
> 
>> On 3/19/26 5:00 AM, Alexander Koskovich wrote:
>>> Add video and command mode destination format mappings for RGB101010,
>>> and extend the VID_CFG0 DST_FORMAT bitfield to 3 bits to accommodate
>>> the new format value.
>>>
>>> Make sure this is guarded behind MSM_DSI_6G_VER >= V2.1.0 as anything
>>> older does not support this.
>>>
>>> Required for 10 bit panels such as the BOE BF068MWM-TD0.
>>>
>>> Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
>>> ---
>>>  drivers/gpu/drm/msm/dsi/dsi_cfg.c             | 8 ++++++++
>>>  drivers/gpu/drm/msm/dsi/dsi_cfg.h             | 1 +
>>>  drivers/gpu/drm/msm/dsi/dsi_host.c            | 9 +++++++++
>>>  drivers/gpu/drm/msm/registers/display/dsi.xml | 5 ++++-
>>>  4 files changed, 22 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/drivers/gpu/drm/msm/dsi/dsi_cfg.c b/drivers/gpu/drm/msm/dsi/dsi_cfg.c
>>> index bd3c51c350e7..6a7ea2183a3b 100644
>>> --- a/drivers/gpu/drm/msm/dsi/dsi_cfg.c
>>> +++ b/drivers/gpu/drm/msm/dsi/dsi_cfg.c
>>> @@ -133,6 +133,7 @@ static const struct msm_dsi_config msm8998_dsi_cfg = {
>>>  	.io_start = {
>>>  		{ 0xc994000, 0xc996000 },
>>>  	},
>>> +	.has_rgb30 = true,
>>
>> I wrote a patch to determine this at runtime, and only after I was done, I
>> noticed that we can already achieve this:
>>
>> bool msm_dsi_host_is_wide_bus_enabled(struct mipi_dsi_host *host)
>> {
>> 	struct msm_dsi_host *msm_host = to_msm_dsi_host(host);
>>
>> 	return msm_host->dsc &&
>> 		(msm_host->cfg_hnd->major == MSM_DSI_VER_MAJOR_6G &&
>> 		 msm_host->cfg_hnd->minor >= MSM_DSI_6G_VER_MINOR_V2_5_0);
>> }
>>
>> let's perhaps extract this to a msm_dsi_host_version_is_gt(u32 major, u32 minor)
>> or similar
> 
> That's what I was looking into initially, but V2_2_0 (0x20000000) is numerically less than V2_1_0 (0x20010000) so didn't think I could do that.

It should be v2.0.0 (0x2(zeroes))

v2.2.0 -> sdm845v1 (unreleased)
v2.2.1 -> sdm670 and sdm845v2

Konrad

Re: [PATCH v2 3/3] drm/msm/dpu: fix video mode DSC INTF timing width for non 8 bit panels

[Konrad Dybcio]

On 3/19/26 9:34 AM, Neil Armstrong wrote:
> On 3/19/26 05:00, Alexander Koskovich wrote:
>> Using bits_per_component * 3 as the divisor for the compressed INTF
>> timing width produces constant FIFO errors for panels such as the BOE
>> BF068MWM-TD0 which is a 10 bit panel.
>>
>> The downstream driver calculates the compressed timing width by
>> dividing the total compressed bytes per line by 3 which does not depend
>> on bits_per_component. Switch the divisor to 24 to match downstream.
>>
>> Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
>> ---
>>   drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 12 +++++++-----
>>   1 file changed, 7 insertions(+), 5 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>> index 0ba777bda253..9b046a0e77aa 100644
>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>> @@ -122,19 +122,21 @@ static void drm_mode_to_intf_timing_params(
>>       }
>>         /*
>> -     * for DSI, if compression is enabled, then divide the horizonal active
>> -     * timing parameters by compression ratio. bits of 3 components(R/G/B)
>> -     * is compressed into bits of 1 pixel.
>> +     * For DSI, if DSC is enabled, use a fixed divisor of 24 rather than
>> +     * bits_per_component * 3 when calculating the compressed timing width.
>> +     *
>> +     * This matches the downstream driver and is required for panels with
>> +     * bits_per_component != 8.
>>        */
>>       if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) {
>>           struct drm_dsc_config *dsc =
>>                  dpu_encoder_get_dsc_config(phys_enc->parent);
>> +
>>           /*
>>            * TODO: replace drm_dsc_get_bpp_int with logic to handle
>>            * fractional part if there is fraction
>>            */
>> -        timing->width = timing->width * drm_dsc_get_bpp_int(dsc) /
>> -                (dsc->bits_per_component * 3);
>> +        timing->width = timing->width * drm_dsc_get_bpp_int(dsc) / 24;
> 
> 
> 
> @bits_per_component: Bits per component to code (8/10/12) <= how the DSC pixels are encoded in the stream
> @bits_per_pixel: Target bits per pixel with 4 fractional bits, bits_per_pixel << 4 <= the target display pixels
> 
> - bits_per_component is the transport width
> - bits_per_pixel is the display width
> - 3 is the DSC compression ratio
> 
> So for a RGB101010 DSC display bits_per_pixel should be 10 << 4
> 
> But here you say bits_per_component should be 8 ? can you share the downstream config of your panel ?
> 
> Are you sure about the bits_per_component & bits_per_pixel values you set in the dsc parameters ?

The computer tells me that if widebus=off, regardless of the compression
ratio and pixel depth before compression, 24 bits of compressed data are
transferred per pclk, and then you can transfer 1/2/4 slices per xfer

(As a note, the DSC compression ratio isn't fixed)

This also impacts the byte/pixel clock calculations (but dsi_host.c seems
to have taken care of that)

Maybe Dmitry knows something more..

Konrad

Re: [PATCH v2 3/3] drm/msm/dpu: fix video mode DSC INTF timing width for non 8 bit panels

[Neil Armstrong]

On 3/19/26 09:48, Alexander Koskovich wrote:
> On Thursday, March 19th, 2026 at 4:35 AM, Neil Armstrong <neil.armstrong@linaro.org> wrote:
> 
>> On 3/19/26 05:00, Alexander Koskovich wrote:
>>> Using bits_per_component * 3 as the divisor for the compressed INTF
>>> timing width produces constant FIFO errors for panels such as the BOE
>>> BF068MWM-TD0 which is a 10 bit panel.
>>>
>>> The downstream driver calculates the compressed timing width by
>>> dividing the total compressed bytes per line by 3 which does not depend
>>> on bits_per_component. Switch the divisor to 24 to match downstream.
>>>
>>> Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
>>> ---
>>>    drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 12 +++++++-----
>>>    1 file changed, 7 insertions(+), 5 deletions(-)
>>>
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>>> index 0ba777bda253..9b046a0e77aa 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
>>> @@ -122,19 +122,21 @@ static void drm_mode_to_intf_timing_params(
>>>    	}
>>>
>>>    	/*
>>> -	 * for DSI, if compression is enabled, then divide the horizonal active
>>> -	 * timing parameters by compression ratio. bits of 3 components(R/G/B)
>>> -	 * is compressed into bits of 1 pixel.
>>> +	 * For DSI, if DSC is enabled, use a fixed divisor of 24 rather than
>>> +	 * bits_per_component * 3 when calculating the compressed timing width.
>>> +	 *
>>> +	 * This matches the downstream driver and is required for panels with
>>> +	 * bits_per_component != 8.
>>>    	 */
>>>    	if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) {
>>>    		struct drm_dsc_config *dsc =
>>>    		       dpu_encoder_get_dsc_config(phys_enc->parent);
>>> +
>>>    		/*
>>>    		 * TODO: replace drm_dsc_get_bpp_int with logic to handle
>>>    		 * fractional part if there is fraction
>>>    		 */
>>> -		timing->width = timing->width * drm_dsc_get_bpp_int(dsc) /
>>> -				(dsc->bits_per_component * 3);
>>> +		timing->width = timing->width * drm_dsc_get_bpp_int(dsc) / 24;
>>
>>
>>
>> @bits_per_component: Bits per component to code (8/10/12) <= how the DSC pixels are encoded in the stream
>> @bits_per_pixel: Target bits per pixel with 4 fractional bits, bits_per_pixel << 4 <= the target display pixels
>>
>> - bits_per_component is the transport width
>> - bits_per_pixel is the display width
>> - 3 is the DSC compression ratio
>>
>> So for a RGB101010 DSC display bits_per_pixel should be 10 << 4
>>
>> But here you say bits_per_component should be 8 ? can you share the downstream config of your panel ?
> 
> This is what is defined downstream for this panel, they're using 8:
> https://github.com/NothingOSS/android_kernel_msm-6.1_nothing_sm7635/blob/sm7635/b/mr/vendor/qcom/proprietary/display-devicetree/display/dsi-panel-rm69220-dsc-fhd-plus-120hz-vid-boe.dtsi
> 
>>
>> Are you sure about the bits_per_component & bits_per_pixel values you set in the dsc parameters ?
> 
> I'm pretty sure they're correct, here's the panel driver I have atm:
> https://github.com/AKoskovich/linux/blob/asteroids-6.19.y/drivers/gpu/drm/panel/panel-boe-bf068mwm-td0.c

So I looked at downstream, and bit-per-component is not used at all for the width calculation.

Here's the full downstream calculation with your panel:


intf_width = mode->timing.h_active;		=> 1080

slice_per_pkt = dsc_info->slice_per_pkt;	=> 2
slice_per_intf = DIV_ROUND_UP(intf_width, dsc_info->config.slice_width);	=> 1080/540 = 2

if (slice_per_pkt > slice_per_intf)
	slice_per_pkt = 1;

bpp = DSC_BPP(dsc_info->config);	=> 8

bytes_in_slice = DIV_ROUND_UP(dsc_info->config.slice_width * bpp, 8);	=> 540 * 8 / 8 = 540


dsc_info->bytes_per_pkt = bytes_in_slice * slice_per_pkt;	=> 540 * 2 = 1080
dsc_info->pkt_per_line = slice_per_intf / slice_per_pkt;	=> 2 / 2 = 1

...

phys->dce_bytes_per_line = comp_info->dsc_info.bytes_per_pkt * comp_info->dsc_info.pkt_per_line; => 1080 * 1 = 1080

...

if (p->compression_en) {
	if (p->wide_bus_en)
		data_width = DIV_ROUND_UP(p->dce_bytes_per_line, 6); => 1080 / 6 = 180
	else
		data_width = DIV_ROUND_UP(p->dce_bytes_per_line, 3); => 1080 / 3 = 360
}

So you're right, it should be a fixed (8 * 3) division, and a (8 * 6) in case of widebus, but DSI widebus is not yet handled.

Neil

> 
>>
>> Neil
>>
>>
>>>    		timing->xres = timing->width;
>>>    	}
>>>    }
>>>
>>
>>
> 
> Thanks,
> Alex