From: xiong <xiong@qca.qualcomm.com>
To: <davem@davemloft.net>, <netdev@vger.kernel.org>,
<linux-kernel@vger.kernel.org>
Cc: <qca-linux-team@qualcomm.com>, <nic-devel@qualcomm.com>,
xiong <xiong@qca.qualcomm.com>
Subject: [PATCH 12/37] atl1c: restore max-read-request-size in Device Conrol Register
Date: Fri, 13 Apr 2012 08:14:37 +0800 [thread overview]
Message-ID: <1334276102-15866-13-git-send-email-xiong@qca.qualcomm.com> (raw)
In-Reply-To: <1334276102-15866-1-git-send-email-xiong@qca.qualcomm.com>
in some platforms, we found the max-read-request-size in Device Control
Register is set to 0 by (BIOS?) during bootup, this will cause the
performance(throughput) very bad.
Restore it to a min-value.
register definition of REG_DEVICE_CTRL is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
---
drivers/net/ethernet/atheros/atl1c/atl1c_hw.h | 21 ++++++++++++++++-----
drivers/net/ethernet/atheros/atl1c/atl1c_main.c | 18 +++++++++++++-----
2 files changed, 29 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h b/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h
index a0b56ef..590ad3d 100644
--- a/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h
+++ b/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h
@@ -54,11 +54,22 @@ int atl1c_phy_power_saving(struct atl1c_hw *hw);
#define DEVICE_CAP_MAX_PAYLOAD_MASK 0x7
#define DEVICE_CAP_MAX_PAYLOAD_SHIFT 0
-#define REG_DEVICE_CTRL 0x60
-#define DEVICE_CTRL_MAX_PAYLOAD_MASK 0x7
-#define DEVICE_CTRL_MAX_PAYLOAD_SHIFT 5
-#define DEVICE_CTRL_MAX_RREQ_SZ_MASK 0x7
-#define DEVICE_CTRL_MAX_RREQ_SZ_SHIFT 12
+#define REG_DEVICE_CTRL 0x60 /* 16bit */
+#define DEVICE_CTRL_MAX_RREQ_SZ_MASK 7U
+#define DEVICE_CTRL_MAX_RREQ_SZ_SHIFT 12
+#define DEVICE_CTRL_MAXRRS_MIN 2
+#define DEVICE_CTRL_NOSNP_EN BIT(11)
+#define DEVICE_CTRL_AUXPWR_EN BIT(10)
+#define DEVICE_CTRL_PHANTOM_EN BIT(9)
+#define DEVICE_CTRL_EXTAG_EN BIT(8)
+#define DEVICE_CTRL_MAX_PAYLOAD_MASK 7U
+#define DEVICE_CTRL_MAX_PAYLOAD_SHIFT 5
+#define DEVICE_CTRL_RELORD_EN BIT(4)
+#define DEVICE_CTRL_URR_EN BIT(3)
+#define DEVICE_CTRL_FERR_EN BIT(2)
+#define DEVICE_CTRL_NFERR_EN BIT(1)
+#define DEVICE_CTRL_CERR_EN BIT(0)
+
#define REG_LINK_CTRL 0x68
#define LINK_CTRL_L0S_EN 0x01
diff --git a/drivers/net/ethernet/atheros/atl1c/atl1c_main.c b/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
index 8e737a5..18c91b6 100644
--- a/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
+++ b/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
@@ -1045,7 +1045,7 @@ static void atl1c_configure_des_ring(struct atl1c_adapter *adapter)
static void atl1c_configure_tx(struct atl1c_adapter *adapter)
{
struct atl1c_hw *hw = &adapter->hw;
- u32 dev_ctrl_data;
+ u16 dev_ctrl_data;
u32 max_pay_load;
u16 tx_offload_thresh;
u32 txq_ctrl_data;
@@ -1053,11 +1053,19 @@ static void atl1c_configure_tx(struct atl1c_adapter *adapter)
tx_offload_thresh = MAX_TX_OFFLOAD_THRESH;
AT_WRITE_REG(hw, REG_TX_TSO_OFFLOAD_THRESH,
(tx_offload_thresh >> 3) & TX_TSO_OFFLOAD_THRESH_MASK);
- AT_READ_REG(hw, REG_DEVICE_CTRL, &dev_ctrl_data);
- max_pay_load = (dev_ctrl_data >> DEVICE_CTRL_MAX_RREQ_SZ_SHIFT) &
- DEVICE_CTRL_MAX_RREQ_SZ_MASK;
+ AT_READ_REGW(hw, REG_DEVICE_CTRL, &dev_ctrl_data);
+ max_pay_load = FIELD_GETX(dev_ctrl_data, DEVICE_CTRL_MAX_RREQ_SZ);
hw->dmar_block = min_t(u32, max_pay_load, hw->dmar_block);
-
+ /*
+ * if BIOS had changed the dam-read-max-length to an invalid value,
+ * restore it to default value
+ */
+ if (hw->dmar_block < DEVICE_CTRL_MAXRRS_MIN) {
+ dev_ctrl_data = FIELD_SETX(dev_ctrl_data,
+ DEVICE_CTRL_MAX_RREQ_SZ, DEVICE_CTRL_MAXRRS_MIN);
+ AT_WRITE_REGW(hw, REG_DEVICE_CTRL, dev_ctrl_data);
+ hw->dmar_block = DEVICE_CTRL_MAXRRS_MIN;
+ }
txq_ctrl_data =
hw->nic_type == athr_l2c_b || hw->nic_type == athr_l2c_b2 ?
L2CB_TXQ_CFGV : L1C_TXQ_CFGV;
--
1.7.7
next prev parent reply other threads:[~2012-04-13 0:17 UTC|newest]
Thread overview: 45+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-04-13 0:14 [PATCH 00/37] atl1c: update hardware settings xiong
2012-04-13 0:14 ` [PATCH 01/37] atl1c: update author contact info & company/driver desciption xiong
2012-04-13 0:14 ` [PATCH 02/37] atl1c: remove multiple-RX-Q code xiong
2012-04-13 0:14 ` [PATCH 03/37] atl1c: remove HDS register xiong
2012-04-13 0:14 ` [PATCH 04/37] atl1c: remove VPD register xiong
2012-04-14 0:45 ` David Miller
2012-04-14 9:12 ` Huang, Xiong
2012-04-14 14:22 ` Ben Hutchings
2012-04-14 18:24 ` David Miller
2012-04-17 8:36 ` Huang, Xiong
2012-04-13 0:14 ` [PATCH 05/37] atl1c: remove SMB/CMB DMA related code xiong
2012-04-13 0:14 ` [PATCH 06/37] atl1c: split 2 32bit registers of TPD to 4 16bit registers xiong
2012-04-13 0:14 ` [PATCH 07/37] atl1c: remove code related to rxq 1/2/3 xiong
2012-04-13 0:14 ` [PATCH 08/37] atl1c: wrong register used to stop TXQ xiong
2012-04-13 0:14 ` [PATCH 09/37] atl1c: correct wrong definition of REG_DMA_CTRL xiong
2012-04-13 0:14 ` [PATCH 10/37] atl1c: remove dmaw_block xiong
2012-04-13 0:14 ` [PATCH 11/37] atl1c: using fixed TXQ configuration for l2cb and l1c xiong
2012-04-13 0:14 ` xiong [this message]
2012-04-13 17:02 ` [PATCH 12/37] atl1c: restore max-read-request-size in Device Conrol Register Ben Hutchings
2012-04-14 10:39 ` Huang, Xiong
2012-04-13 0:14 ` [PATCH 13/37] atl1c: threshold for ASPM is changed based on chip capability xiong
2012-04-13 0:14 ` [PATCH 14/37] atl1c: add module parameter for l1c_wait_until_idle xiong
2012-04-13 0:14 ` [PATCH 15/37] atl1c: update right threshold for TSO xiong
2012-04-13 0:14 ` [PATCH 16/37] atl1c: remove dmar_dly_cnt and dmaw_dly_cnt xiong
2012-04-13 0:14 ` [PATCH 17/37] atl1c: clear PCIE error status in atl1c_reset_pcie xiong
2012-04-13 0:14 ` [PATCH 18/37] atl1c: refine reg definition of REG_MASTER_CTRL xiong
2012-04-13 0:14 ` [PATCH 19/37] atl1c: clear bit MASTER_CTRL_CLK_SEL_DIS in atl1c_pcie_patch xiong
2012-04-13 0:14 ` [PATCH 20/37] atl1c: refine/update ASPM configuration xiong
2012-04-13 0:14 ` [PATCH 21/37] atl1c: refine atl1c_pcie_patch xiong
2012-04-13 0:14 ` [PATCH 22/37] atl1c: fix WoL(magic) issue for l2cb 1.1 xiong
2012-04-13 0:14 ` [PATCH 23/37] atl1c: remove MDIO_REG_ADDR_MASK in atl1c_mdio_read/write xiong
2012-04-13 0:14 ` [PATCH 24/37] atl1c: remove REG_PHY_STATUS xiong
2012-04-13 0:14 ` [PATCH 25/37] atl1c: refine phy-register read/write function xiong
2012-04-13 0:14 ` [PATCH 26/37] atl1c: remove PHY contrl in atl1c_reset_pcie xiong
2012-04-13 0:14 ` [PATCH 27/37] atl1c: refine SERDES-clock related code xiong
2012-04-13 0:14 ` [PATCH 28/37] atl1c: remove PHY polling from atl1c_open xiong
2012-04-13 0:14 ` [PATCH 29/37] atl1c: update PHY reset related routine xiong
2012-04-13 0:14 ` [PATCH 30/37] atl1c: remove PHY reset/init for link down event xiong
2012-04-13 0:14 ` [PATCH 31/37] atl1c: add function atl1c_power_saving xiong
2012-04-13 0:14 ` [PATCH 32/37] atl1c: refine start/enable code for MAC module xiong
2012-04-13 0:14 ` [PATCH 33/37] atl1c: add PHY link event(up/down) patch xiong
2012-04-13 0:14 ` [PATCH 34/37] atl1c: clear WoL status when reset pcie xiong
2012-04-13 0:15 ` [PATCH 35/37] atl1c: remove code of closing register writable attribution xiong
2012-04-13 0:15 ` [PATCH 36/37] atl1c: refine mac address related code xiong
2012-04-13 0:15 ` [PATCH 37/37] atl1c: cancel task when interface closed xiong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1334276102-15866-13-git-send-email-xiong@qca.qualcomm.com \
--to=xiong@qca.qualcomm.com \
--cc=davem@davemloft.net \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=nic-devel@qualcomm.com \
--cc=qca-linux-team@qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®