From: xiong <xiong@qca.qualcomm.com>
To: <davem@davemloft.net>, <netdev@vger.kernel.org>,
<linux-kernel@vger.kernel.org>
Cc: <qca-linux-team@qualcomm.com>, <nic-devel@qualcomm.com>,
xiong <xiong@qca.qualcomm.com>
Subject: [PATCH 20/37] atl1c: refine/update ASPM configuration
Date: Fri, 13 Apr 2012 08:14:45 +0800 [thread overview]
Message-ID: <1334276102-15866-21-git-send-email-xiong@qca.qualcomm.com> (raw)
In-Reply-To: <1334276102-15866-1-git-send-email-xiong@qca.qualcomm.com>
some platforms(BIOS or OS) may change ASPM configuration in
PCI Express Link Control Register directly and dynamically
regardless the device driver installation.
Checking if ASPM support during the driver init phase by reading
PCI Express Link Contrl Register doesn't make sense.
This refine/update assume L0S/L1 is defalut enabled as hw->ctrl_flags
inited. atl1c_set_aspm will set real configuration based on chip
capability to hardware register.
atl1c_disable_l0s_l1 and register definition of REG_PM_CTRL are
refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
---
drivers/net/ethernet/atheros/atl1c/atl1c_hw.h | 66 ++++++---
drivers/net/ethernet/atheros/atl1c/atl1c_main.c | 167 +++++++++-------------
2 files changed, 111 insertions(+), 122 deletions(-)
diff --git a/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h b/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h
index 8246c29..3a5e451 100644
--- a/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h
+++ b/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h
@@ -161,30 +161,50 @@ int atl1c_phy_power_saving(struct atl1c_hw *hw);
#define OTP_CTRL_CLK_EN 0x0002
#define REG_PM_CTRL 0x12F8
-#define PM_CTRL_SDES_EN 0x00000001
-#define PM_CTRL_RBER_EN 0x00000002
-#define PM_CTRL_CLK_REQ_EN 0x00000004
-#define PM_CTRL_ASPM_L1_EN 0x00000008
-#define PM_CTRL_SERDES_L1_EN 0x00000010
-#define PM_CTRL_SERDES_PLL_L1_EN 0x00000020
-#define PM_CTRL_SERDES_PD_EX_L1 0x00000040
-#define PM_CTRL_SERDES_BUDS_RX_L1_EN 0x00000080
-#define PM_CTRL_L0S_ENTRY_TIMER_MASK 0xF
-#define PM_CTRL_L0S_ENTRY_TIMER_SHIFT 8
-#define PM_CTRL_ASPM_L0S_EN 0x00001000
-#define PM_CTRL_CLK_SWH_L1 0x00002000
-#define PM_CTRL_CLK_PWM_VER1_1 0x00004000
-#define PM_CTRL_RCVR_WT_TIMER 0x00008000
-#define PM_CTRL_L1_ENTRY_TIMER_MASK 0xF
-#define PM_CTRL_L1_ENTRY_TIMER_SHIFT 16
-#define PM_CTRL_PM_REQ_TIMER_MASK 0xF
-#define PM_CTRL_PM_REQ_TIMER_SHIFT 20
-#define PM_CTRL_LCKDET_TIMER_MASK 0xF
+#define PM_CTRL_HOTRST BIT(31)
+#define PM_CTRL_MAC_ASPM_CHK BIT(30) /* L0s/L1 dis by MAC based on
+ * thrghput(setting in 15A0) */
+#define PM_CTRL_SA_DLY_EN BIT(29)
+#define PM_CTRL_L0S_BUFSRX_EN BIT(28)
+#define PM_CTRL_LCKDET_TIMER_MASK 0xFUL
#define PM_CTRL_LCKDET_TIMER_SHIFT 24
-#define PM_CTRL_EN_BUFS_RX_L0S 0x10000000
-#define PM_CTRL_SA_DLY_EN 0x20000000
-#define PM_CTRL_MAC_ASPM_CHK 0x40000000
-#define PM_CTRL_HOTRST 0x80000000
+#define PM_CTRL_LCKDET_TIMER_DEF 0xC
+#define PM_CTRL_PM_REQ_TIMER_MASK 0xFUL
+#define PM_CTRL_PM_REQ_TIMER_SHIFT 20 /* pm_request_l1 time > @
+ * ->L0s not L1 */
+#define PM_CTRL_PM_REQ_TO_DEF 0xC
+#define PMCTRL_TXL1_AFTER_L0S BIT(19) /* l1dv2.0+ */
+#define L1D_PMCTRL_L1_ENTRY_TM_MASK 7UL /* l1dv2.0+, 3bits */
+#define L1D_PMCTRL_L1_ENTRY_TM_SHIFT 16
+#define L1D_PMCTRL_L1_ENTRY_TM_DIS 0
+#define L1D_PMCTRL_L1_ENTRY_TM_2US 1
+#define L1D_PMCTRL_L1_ENTRY_TM_4US 2
+#define L1D_PMCTRL_L1_ENTRY_TM_8US 3
+#define L1D_PMCTRL_L1_ENTRY_TM_16US 4
+#define L1D_PMCTRL_L1_ENTRY_TM_24US 5
+#define L1D_PMCTRL_L1_ENTRY_TM_32US 6
+#define L1D_PMCTRL_L1_ENTRY_TM_63US 7
+#define PM_CTRL_L1_ENTRY_TIMER_MASK 0xFUL /* l1C 4bits */
+#define PM_CTRL_L1_ENTRY_TIMER_SHIFT 16
+#define L2CB1_PM_CTRL_L1_ENTRY_TM 7
+#define L1C_PM_CTRL_L1_ENTRY_TM 0xF
+#define PM_CTRL_RCVR_WT_TIMER BIT(15) /* 1:1us, 0:2ms */
+#define PM_CTRL_CLK_PWM_VER1_1 BIT(14) /* 0:1.0a,1:1.1 */
+#define PM_CTRL_CLK_SWH_L1 BIT(13) /* en pcie clk sw in L1 */
+#define PM_CTRL_ASPM_L0S_EN BIT(12)
+#define PM_CTRL_RXL1_AFTER_L0S BIT(11) /* l1dv2.0+ */
+#define L1D_PMCTRL_L0S_TIMER_MASK 7UL /* l1d2.0+, 3bits*/
+#define L1D_PMCTRL_L0S_TIMER_SHIFT 8
+#define PM_CTRL_L0S_ENTRY_TIMER_MASK 0xFUL /* l1c, 4bits */
+#define PM_CTRL_L0S_ENTRY_TIMER_SHIFT 8
+#define PM_CTRL_SERDES_BUFS_RX_L1_EN BIT(7)
+#define PM_CTRL_SERDES_PD_EX_L1 BIT(6) /* power down serdes rx */
+#define PM_CTRL_SERDES_PLL_L1_EN BIT(5)
+#define PM_CTRL_SERDES_L1_EN BIT(4)
+#define PM_CTRL_ASPM_L1_EN BIT(3)
+#define PM_CTRL_CLK_REQ_EN BIT(2)
+#define PM_CTRL_RBER_EN BIT(1)
+#define PM_CTRL_SPRSDWER_EN BIT(0)
#define REG_LTSSM_ID_CTRL 0x12FC
#define LTSSM_ID_EN_WRO 0x1000
diff --git a/drivers/net/ethernet/atheros/atl1c/atl1c_main.c b/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
index ddffc48..8890e7f 100644
--- a/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
+++ b/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
@@ -64,7 +64,7 @@ static int atl1c_stop_mac(struct atl1c_hw *hw);
static void atl1c_enable_rx_ctrl(struct atl1c_hw *hw);
static void atl1c_enable_tx_ctrl(struct atl1c_hw *hw);
static void atl1c_disable_l0s_l1(struct atl1c_hw *hw);
-static void atl1c_set_aspm(struct atl1c_hw *hw, bool linkup);
+static void atl1c_set_aspm(struct atl1c_hw *hw, u16 link_speed);
static void atl1c_setup_mac_ctrl(struct atl1c_adapter *adapter);
static void atl1c_clean_rx_irq(struct atl1c_adapter *adapter,
int *work_done, int work_to_do);
@@ -249,7 +249,7 @@ static void atl1c_check_link_status(struct atl1c_adapter *adapter)
if (atl1c_stop_mac(hw) != 0)
if (netif_msg_hw(adapter))
dev_warn(&pdev->dev, "stop mac failed\n");
- atl1c_set_aspm(hw, false);
+ atl1c_set_aspm(hw, SPEED_0);
netif_carrier_off(netdev);
netif_stop_queue(netdev);
atl1c_phy_reset(hw);
@@ -267,7 +267,7 @@ static void atl1c_check_link_status(struct atl1c_adapter *adapter)
adapter->link_duplex != duplex) {
adapter->link_speed = speed;
adapter->link_duplex = duplex;
- atl1c_set_aspm(hw, true);
+ atl1c_set_aspm(hw, speed);
atl1c_enable_tx_ctrl(hw);
atl1c_enable_rx_ctrl(hw);
atl1c_setup_mac_ctrl(adapter);
@@ -685,12 +685,8 @@ static int atl1c_setup_mac_funcs(struct atl1c_hw *hw)
hw->ctrl_flags = ATL1C_INTR_MODRT_ENABLE |
ATL1C_TXQ_MODE_ENHANCE;
- if (link_ctrl_data & LINK_CTRL_L0S_EN)
- hw->ctrl_flags |= ATL1C_ASPM_L0S_SUPPORT;
- if (link_ctrl_data & LINK_CTRL_L1_EN)
- hw->ctrl_flags |= ATL1C_ASPM_L1_SUPPORT;
- if (link_ctrl_data & LINK_CTRL_EXT_SYNC)
- hw->ctrl_flags |= ATL1C_LINK_EXT_SYNC;
+ hw->ctrl_flags |= ATL1C_ASPM_L0S_SUPPORT |
+ ATL1C_ASPM_L1_SUPPORT;
hw->ctrl_flags |= ATL1C_ASPM_CTRL_MON;
if (hw->nic_type == athr_l1c ||
@@ -1201,112 +1197,83 @@ static int atl1c_reset_mac(struct atl1c_hw *hw)
static void atl1c_disable_l0s_l1(struct atl1c_hw *hw)
{
- u32 pm_ctrl_data;
-
- AT_READ_REG(hw, REG_PM_CTRL, &pm_ctrl_data);
- pm_ctrl_data &= ~(PM_CTRL_L1_ENTRY_TIMER_MASK <<
- PM_CTRL_L1_ENTRY_TIMER_SHIFT);
- pm_ctrl_data &= ~PM_CTRL_CLK_SWH_L1;
- pm_ctrl_data &= ~PM_CTRL_ASPM_L0S_EN;
- pm_ctrl_data &= ~PM_CTRL_ASPM_L1_EN;
- pm_ctrl_data &= ~PM_CTRL_MAC_ASPM_CHK;
- pm_ctrl_data &= ~PM_CTRL_SERDES_PD_EX_L1;
+ u16 ctrl_flags = hw->ctrl_flags;
- pm_ctrl_data |= PM_CTRL_SERDES_BUDS_RX_L1_EN;
- pm_ctrl_data |= PM_CTRL_SERDES_PLL_L1_EN;
- pm_ctrl_data |= PM_CTRL_SERDES_L1_EN;
- AT_WRITE_REG(hw, REG_PM_CTRL, pm_ctrl_data);
+ hw->ctrl_flags &= ~(ATL1C_ASPM_L0S_SUPPORT | ATL1C_ASPM_L1_SUPPORT);
+ atl1c_set_aspm(hw, SPEED_0);
+ hw->ctrl_flags = ctrl_flags;
}
/*
* Set ASPM state.
* Enable/disable L0s/L1 depend on link state.
*/
-static void atl1c_set_aspm(struct atl1c_hw *hw, bool linkup)
+static void atl1c_set_aspm(struct atl1c_hw *hw, u16 link_speed)
{
u32 pm_ctrl_data;
- u32 link_ctrl_data;
- u32 link_l1_timer = 0xF;
+ u32 link_l1_timer;
AT_READ_REG(hw, REG_PM_CTRL, &pm_ctrl_data);
- AT_READ_REG(hw, REG_LINK_CTRL, &link_ctrl_data);
+ pm_ctrl_data &= ~(PM_CTRL_ASPM_L1_EN |
+ PM_CTRL_ASPM_L0S_EN |
+ PM_CTRL_MAC_ASPM_CHK);
+ /* L1 timer */
+ if (hw->nic_type == athr_l2c_b2 || hw->nic_type == athr_l1d_2) {
+ pm_ctrl_data &= ~PMCTRL_TXL1_AFTER_L0S;
+ link_l1_timer =
+ link_speed == SPEED_1000 || link_speed == SPEED_100 ?
+ L1D_PMCTRL_L1_ENTRY_TM_16US : 1;
+ pm_ctrl_data = FIELD_SETX(pm_ctrl_data,
+ L1D_PMCTRL_L1_ENTRY_TM, link_l1_timer);
+ } else {
+ link_l1_timer = hw->nic_type == athr_l2c_b ?
+ L2CB1_PM_CTRL_L1_ENTRY_TM : L1C_PM_CTRL_L1_ENTRY_TM;
+ if (link_speed != SPEED_1000 && link_speed != SPEED_100)
+ link_l1_timer = 1;
+ pm_ctrl_data = FIELD_SETX(pm_ctrl_data,
+ PM_CTRL_L1_ENTRY_TIMER, link_l1_timer);
+ }
- pm_ctrl_data &= ~PM_CTRL_SERDES_PD_EX_L1;
- pm_ctrl_data &= ~(PM_CTRL_L1_ENTRY_TIMER_MASK <<
- PM_CTRL_L1_ENTRY_TIMER_SHIFT);
- pm_ctrl_data &= ~(PM_CTRL_LCKDET_TIMER_MASK <<
- PM_CTRL_LCKDET_TIMER_SHIFT);
- pm_ctrl_data |= AT_LCKDET_TIMER << PM_CTRL_LCKDET_TIMER_SHIFT;
+ /* L0S/L1 enable */
+ if (hw->ctrl_flags & ATL1C_ASPM_L0S_SUPPORT)
+ pm_ctrl_data |= PM_CTRL_ASPM_L0S_EN | PM_CTRL_MAC_ASPM_CHK;
+ if (hw->ctrl_flags & ATL1C_ASPM_L1_SUPPORT)
+ pm_ctrl_data |= PM_CTRL_ASPM_L1_EN | PM_CTRL_MAC_ASPM_CHK;
+ /* l2cb & l1d & l2cb2 & l1d2 */
if (hw->nic_type == athr_l2c_b || hw->nic_type == athr_l1d ||
- hw->nic_type == athr_l2c_b2 || hw->nic_type == athr_l1d_2) {
- link_ctrl_data &= ~LINK_CTRL_EXT_SYNC;
- if (!(hw->ctrl_flags & ATL1C_APS_MODE_ENABLE)) {
- if (hw->nic_type == athr_l2c_b && hw->revision_id == L2CB_V10)
- link_ctrl_data |= LINK_CTRL_EXT_SYNC;
- }
-
- AT_WRITE_REG(hw, REG_LINK_CTRL, link_ctrl_data);
-
- pm_ctrl_data |= PM_CTRL_RCVR_WT_TIMER;
- pm_ctrl_data &= ~(PM_CTRL_PM_REQ_TIMER_MASK <<
- PM_CTRL_PM_REQ_TIMER_SHIFT);
- pm_ctrl_data |= AT_ASPM_L1_TIMER <<
- PM_CTRL_PM_REQ_TIMER_SHIFT;
- pm_ctrl_data &= ~PM_CTRL_SA_DLY_EN;
- pm_ctrl_data &= ~PM_CTRL_HOTRST;
- pm_ctrl_data |= 1 << PM_CTRL_L1_ENTRY_TIMER_SHIFT;
- pm_ctrl_data |= PM_CTRL_SERDES_PD_EX_L1;
- }
- pm_ctrl_data |= PM_CTRL_MAC_ASPM_CHK;
- if (linkup) {
- pm_ctrl_data &= ~PM_CTRL_ASPM_L1_EN;
- pm_ctrl_data &= ~PM_CTRL_ASPM_L0S_EN;
- if (hw->ctrl_flags & ATL1C_ASPM_L1_SUPPORT)
- pm_ctrl_data |= PM_CTRL_ASPM_L1_EN;
- if (hw->ctrl_flags & ATL1C_ASPM_L0S_SUPPORT)
- pm_ctrl_data |= PM_CTRL_ASPM_L0S_EN;
-
- if (hw->nic_type == athr_l2c_b || hw->nic_type == athr_l1d ||
- hw->nic_type == athr_l2c_b2 || hw->nic_type == athr_l1d_2) {
- if (hw->nic_type == athr_l2c_b)
- if (!(hw->ctrl_flags & ATL1C_APS_MODE_ENABLE))
- pm_ctrl_data &= ~PM_CTRL_ASPM_L0S_EN;
- pm_ctrl_data &= ~PM_CTRL_SERDES_L1_EN;
- pm_ctrl_data &= ~PM_CTRL_SERDES_PLL_L1_EN;
- pm_ctrl_data &= ~PM_CTRL_SERDES_BUDS_RX_L1_EN;
- pm_ctrl_data |= PM_CTRL_CLK_SWH_L1;
- if (hw->adapter->link_speed == SPEED_100 ||
- hw->adapter->link_speed == SPEED_1000) {
- pm_ctrl_data &= ~(PM_CTRL_L1_ENTRY_TIMER_MASK <<
- PM_CTRL_L1_ENTRY_TIMER_SHIFT);
- if (hw->nic_type == athr_l2c_b)
- link_l1_timer = 7;
- else if (hw->nic_type == athr_l2c_b2 ||
- hw->nic_type == athr_l1d_2)
- link_l1_timer = 4;
- pm_ctrl_data |= link_l1_timer <<
- PM_CTRL_L1_ENTRY_TIMER_SHIFT;
- }
- } else {
- pm_ctrl_data |= PM_CTRL_SERDES_L1_EN;
- pm_ctrl_data |= PM_CTRL_SERDES_PLL_L1_EN;
- pm_ctrl_data |= PM_CTRL_SERDES_BUDS_RX_L1_EN;
- pm_ctrl_data &= ~PM_CTRL_CLK_SWH_L1;
+ hw->nic_type == athr_l2c_b2 || hw->nic_type == athr_l1d_2) {
+ pm_ctrl_data = FIELD_SETX(pm_ctrl_data,
+ PM_CTRL_PM_REQ_TIMER, PM_CTRL_PM_REQ_TO_DEF);
+ pm_ctrl_data |= PM_CTRL_RCVR_WT_TIMER |
+ PM_CTRL_SERDES_PD_EX_L1 |
+ PM_CTRL_CLK_SWH_L1;
+ pm_ctrl_data &= ~(PM_CTRL_SERDES_L1_EN |
+ PM_CTRL_SERDES_PLL_L1_EN |
+ PM_CTRL_SERDES_BUFS_RX_L1_EN |
+ PM_CTRL_SA_DLY_EN |
+ PM_CTRL_HOTRST);
+ /* disable l0s if link down or l2cb */
+ if (link_speed == SPEED_0 || hw->nic_type == athr_l2c_b)
pm_ctrl_data &= ~PM_CTRL_ASPM_L0S_EN;
- pm_ctrl_data &= ~PM_CTRL_ASPM_L1_EN;
-
+ } else { /* l1c */
+ pm_ctrl_data =
+ FIELD_SETX(pm_ctrl_data, PM_CTRL_L1_ENTRY_TIMER, 0);
+ if (link_speed != SPEED_0) {
+ pm_ctrl_data |= PM_CTRL_SERDES_L1_EN |
+ PM_CTRL_SERDES_PLL_L1_EN |
+ PM_CTRL_SERDES_BUFS_RX_L1_EN;
+ pm_ctrl_data &= ~(PM_CTRL_SERDES_PD_EX_L1 |
+ PM_CTRL_CLK_SWH_L1 |
+ PM_CTRL_ASPM_L0S_EN |
+ PM_CTRL_ASPM_L1_EN);
+ } else { /* link down */
+ pm_ctrl_data |= PM_CTRL_CLK_SWH_L1;
+ pm_ctrl_data &= ~(PM_CTRL_SERDES_L1_EN |
+ PM_CTRL_SERDES_PLL_L1_EN |
+ PM_CTRL_SERDES_BUFS_RX_L1_EN |
+ PM_CTRL_ASPM_L0S_EN);
}
- } else {
- pm_ctrl_data &= ~PM_CTRL_SERDES_L1_EN;
- pm_ctrl_data &= ~PM_CTRL_ASPM_L0S_EN;
- pm_ctrl_data &= ~PM_CTRL_SERDES_PLL_L1_EN;
- pm_ctrl_data |= PM_CTRL_CLK_SWH_L1;
-
- if (hw->ctrl_flags & ATL1C_ASPM_L1_SUPPORT)
- pm_ctrl_data |= PM_CTRL_ASPM_L1_EN;
- else
- pm_ctrl_data &= ~PM_CTRL_ASPM_L1_EN;
}
AT_WRITE_REG(hw, REG_PM_CTRL, pm_ctrl_data);
@@ -2234,6 +2201,8 @@ static void atl1c_down(struct atl1c_adapter *adapter)
napi_disable(&adapter->napi);
atl1c_irq_disable(adapter);
atl1c_free_irq(adapter);
+ /* disable ASPM if device inactive */
+ atl1c_disable_l0s_l1(&adapter->hw);
/* reset MAC to disable all RX/TX */
atl1c_reset_mac(&adapter->hw);
msleep(1);
--
1.7.7
next prev parent reply other threads:[~2012-04-13 0:23 UTC|newest]
Thread overview: 45+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-04-13 0:14 [PATCH 00/37] atl1c: update hardware settings xiong
2012-04-13 0:14 ` [PATCH 01/37] atl1c: update author contact info & company/driver desciption xiong
2012-04-13 0:14 ` [PATCH 02/37] atl1c: remove multiple-RX-Q code xiong
2012-04-13 0:14 ` [PATCH 03/37] atl1c: remove HDS register xiong
2012-04-13 0:14 ` [PATCH 04/37] atl1c: remove VPD register xiong
2012-04-14 0:45 ` David Miller
2012-04-14 9:12 ` Huang, Xiong
2012-04-14 14:22 ` Ben Hutchings
2012-04-14 18:24 ` David Miller
2012-04-17 8:36 ` Huang, Xiong
2012-04-13 0:14 ` [PATCH 05/37] atl1c: remove SMB/CMB DMA related code xiong
2012-04-13 0:14 ` [PATCH 06/37] atl1c: split 2 32bit registers of TPD to 4 16bit registers xiong
2012-04-13 0:14 ` [PATCH 07/37] atl1c: remove code related to rxq 1/2/3 xiong
2012-04-13 0:14 ` [PATCH 08/37] atl1c: wrong register used to stop TXQ xiong
2012-04-13 0:14 ` [PATCH 09/37] atl1c: correct wrong definition of REG_DMA_CTRL xiong
2012-04-13 0:14 ` [PATCH 10/37] atl1c: remove dmaw_block xiong
2012-04-13 0:14 ` [PATCH 11/37] atl1c: using fixed TXQ configuration for l2cb and l1c xiong
2012-04-13 0:14 ` [PATCH 12/37] atl1c: restore max-read-request-size in Device Conrol Register xiong
2012-04-13 17:02 ` Ben Hutchings
2012-04-14 10:39 ` Huang, Xiong
2012-04-13 0:14 ` [PATCH 13/37] atl1c: threshold for ASPM is changed based on chip capability xiong
2012-04-13 0:14 ` [PATCH 14/37] atl1c: add module parameter for l1c_wait_until_idle xiong
2012-04-13 0:14 ` [PATCH 15/37] atl1c: update right threshold for TSO xiong
2012-04-13 0:14 ` [PATCH 16/37] atl1c: remove dmar_dly_cnt and dmaw_dly_cnt xiong
2012-04-13 0:14 ` [PATCH 17/37] atl1c: clear PCIE error status in atl1c_reset_pcie xiong
2012-04-13 0:14 ` [PATCH 18/37] atl1c: refine reg definition of REG_MASTER_CTRL xiong
2012-04-13 0:14 ` [PATCH 19/37] atl1c: clear bit MASTER_CTRL_CLK_SEL_DIS in atl1c_pcie_patch xiong
2012-04-13 0:14 ` xiong [this message]
2012-04-13 0:14 ` [PATCH 21/37] atl1c: refine atl1c_pcie_patch xiong
2012-04-13 0:14 ` [PATCH 22/37] atl1c: fix WoL(magic) issue for l2cb 1.1 xiong
2012-04-13 0:14 ` [PATCH 23/37] atl1c: remove MDIO_REG_ADDR_MASK in atl1c_mdio_read/write xiong
2012-04-13 0:14 ` [PATCH 24/37] atl1c: remove REG_PHY_STATUS xiong
2012-04-13 0:14 ` [PATCH 25/37] atl1c: refine phy-register read/write function xiong
2012-04-13 0:14 ` [PATCH 26/37] atl1c: remove PHY contrl in atl1c_reset_pcie xiong
2012-04-13 0:14 ` [PATCH 27/37] atl1c: refine SERDES-clock related code xiong
2012-04-13 0:14 ` [PATCH 28/37] atl1c: remove PHY polling from atl1c_open xiong
2012-04-13 0:14 ` [PATCH 29/37] atl1c: update PHY reset related routine xiong
2012-04-13 0:14 ` [PATCH 30/37] atl1c: remove PHY reset/init for link down event xiong
2012-04-13 0:14 ` [PATCH 31/37] atl1c: add function atl1c_power_saving xiong
2012-04-13 0:14 ` [PATCH 32/37] atl1c: refine start/enable code for MAC module xiong
2012-04-13 0:14 ` [PATCH 33/37] atl1c: add PHY link event(up/down) patch xiong
2012-04-13 0:14 ` [PATCH 34/37] atl1c: clear WoL status when reset pcie xiong
2012-04-13 0:15 ` [PATCH 35/37] atl1c: remove code of closing register writable attribution xiong
2012-04-13 0:15 ` [PATCH 36/37] atl1c: refine mac address related code xiong
2012-04-13 0:15 ` [PATCH 37/37] atl1c: cancel task when interface closed xiong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1334276102-15866-21-git-send-email-xiong@qca.qualcomm.com \
--to=xiong@qca.qualcomm.com \
--cc=davem@davemloft.net \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=nic-devel@qualcomm.com \
--cc=qca-linux-team@qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®