From: xiong <xiong@qca.qualcomm.com>
To: <davem@davemloft.net>, <netdev@vger.kernel.org>,
<linux-kernel@vger.kernel.org>
Cc: <qca-linux-team@qualcomm.com>, <nic-devel@qualcomm.com>,
xiong <xiong@qca.qualcomm.com>
Subject: [PATCH 21/37] atl1c: refine atl1c_pcie_patch
Date: Fri, 13 Apr 2012 08:14:46 +0800 [thread overview]
Message-ID: <1334276102-15866-22-git-send-email-xiong@qca.qualcomm.com> (raw)
In-Reply-To: <1334276102-15866-1-git-send-email-xiong@qca.qualcomm.com>
bit PCIE_PHYMISC_FORCE_RCV_DET is only for l1c&l2c to fix WoL issue,
other chips set bit5 of REG_MASTER_CTRL --- this way could save more
power than the former, and the bit should be kept all time.
l2cb 1.x has special setting for L0S/L1
l2cb 1.x & l1d 1.x should clear Vendor Message on some platforms,
otherwise it will cause the root complex hang.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
---
drivers/net/ethernet/atheros/atl1c/atl1c_hw.h | 17 ++++++--
drivers/net/ethernet/atheros/atl1c/atl1c_main.c | 49 +++++++++++++++++------
2 files changed, 48 insertions(+), 18 deletions(-)
diff --git a/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h b/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h
index 3a5e451..aafe4ff 100644
--- a/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h
+++ b/drivers/net/ethernet/atheros/atl1c/atl1c_hw.h
@@ -136,17 +136,24 @@ int atl1c_phy_power_saving(struct atl1c_hw *hw);
#define PCIE_DEV_MISC_SERDES_SEL_DIN 0x10
#define REG_PCIE_PHYMISC 0x1000
-#define PCIE_PHYMISC_FORCE_RCV_DET 0x4
+#define PCIE_PHYMISC_FORCE_RCV_DET BIT(2)
+#define PCIE_PHYMISC_NFTS_MASK 0xFFUL
+#define PCIE_PHYMISC_NFTS_SHIFT 16
#define REG_PCIE_PHYMISC2 0x1004
-#define PCIE_PHYMISC2_SERDES_CDR_MASK 0x3
-#define PCIE_PHYMISC2_SERDES_CDR_SHIFT 16
-#define PCIE_PHYMISC2_SERDES_TH_MASK 0x3
-#define PCIE_PHYMISC2_SERDES_TH_SHIFT 18
+#define PCIE_PHYMISC2_L0S_TH_MASK 0x3UL
+#define PCIE_PHYMISC2_L0S_TH_SHIFT 18
+#define L2CB1_PCIE_PHYMISC2_L0S_TH 3
+#define PCIE_PHYMISC2_CDR_BW_MASK 0x3UL
+#define PCIE_PHYMISC2_CDR_BW_SHIFT 16
+#define L2CB1_PCIE_PHYMISC2_CDR_BW 3
#define REG_TWSI_DEBUG 0x1108
#define TWSI_DEBUG_DEV_EXIST 0x20000000
+#define REG_DMA_DBG 0x1114
+#define DMA_DBG_VENDOR_MSG BIT(0)
+
#define REG_EEPROM_CTRL 0x12C0
#define EEPROM_CTRL_DATA_HI_MASK 0xFFFF
#define EEPROM_CTRL_DATA_HI_SHIFT 0
diff --git a/drivers/net/ethernet/atheros/atl1c/atl1c_main.c b/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
index 8890e7f..8955810 100644
--- a/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
+++ b/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
@@ -87,20 +87,37 @@ static void atl1c_pcie_patch(struct atl1c_hw *hw)
mst_data &= ~MASTER_CTRL_CLK_SEL_DIS;
AT_WRITE_REG(hw, REG_MASTER_CTRL, mst_data);
- AT_READ_REG(hw, REG_PCIE_PHYMISC, &data);
- data |= PCIE_PHYMISC_FORCE_RCV_DET;
- AT_WRITE_REG(hw, REG_PCIE_PHYMISC, data);
-
+ /* WoL/PCIE related settings */
+ if (hw->nic_type == athr_l1c || hw->nic_type == athr_l2c) {
+ AT_READ_REG(hw, REG_PCIE_PHYMISC, &data);
+ data |= PCIE_PHYMISC_FORCE_RCV_DET;
+ AT_WRITE_REG(hw, REG_PCIE_PHYMISC, data);
+ } else { /* new dev set bit5 of MASTER */
+ if (!(mst_data & MASTER_CTRL_WAKEN_25M))
+ AT_WRITE_REG(hw, REG_MASTER_CTRL,
+ mst_data | MASTER_CTRL_WAKEN_25M);
+ }
+ /* aspm/PCIE setting only for l2cb 1.0 */
if (hw->nic_type == athr_l2c_b && hw->revision_id == L2CB_V10) {
AT_READ_REG(hw, REG_PCIE_PHYMISC2, &data);
-
- data &= ~(PCIE_PHYMISC2_SERDES_CDR_MASK <<
- PCIE_PHYMISC2_SERDES_CDR_SHIFT);
- data |= 3 << PCIE_PHYMISC2_SERDES_CDR_SHIFT;
- data &= ~(PCIE_PHYMISC2_SERDES_TH_MASK <<
- PCIE_PHYMISC2_SERDES_TH_SHIFT);
- data |= 3 << PCIE_PHYMISC2_SERDES_TH_SHIFT;
+ data = FIELD_SETX(data, PCIE_PHYMISC2_CDR_BW,
+ L2CB1_PCIE_PHYMISC2_CDR_BW);
+ data = FIELD_SETX(data, PCIE_PHYMISC2_L0S_TH,
+ L2CB1_PCIE_PHYMISC2_L0S_TH);
AT_WRITE_REG(hw, REG_PCIE_PHYMISC2, data);
+ /* extend L1 sync timer */
+ AT_READ_REG(hw, REG_LINK_CTRL, &data);
+ data |= LINK_CTRL_EXT_SYNC;
+ AT_WRITE_REG(hw, REG_LINK_CTRL, data);
+ }
+ /* l2cb 1.x & l1d 1.x */
+ if (hw->nic_type == athr_l2c_b || hw->nic_type == athr_l1d) {
+ AT_READ_REG(hw, REG_PM_CTRL, &data);
+ data |= PM_CTRL_L0S_BUFSRX_EN;
+ AT_WRITE_REG(hw, REG_PM_CTRL, data);
+ /* clear vendor msg */
+ AT_READ_REG(hw, REG_DMA_DBG, &data);
+ AT_WRITE_REG(hw, REG_DMA_DBG, data & ~DMA_DBG_VENDOR_MSG);
}
}
@@ -1179,8 +1196,8 @@ static int atl1c_reset_mac(struct atl1c_hw *hw)
*/
AT_READ_REG(hw, REG_MASTER_CTRL, &master_ctrl_data);
master_ctrl_data |= MASTER_CTRL_OOB_DIS;
- AT_WRITE_REGW(hw, REG_MASTER_CTRL, ((master_ctrl_data | MASTER_CTRL_SOFT_RST)
- & 0xFFFF));
+ AT_WRITE_REG(hw, REG_MASTER_CTRL,
+ master_ctrl_data | MASTER_CTRL_SOFT_RST);
AT_WRITE_FLUSH(hw);
msleep(10);
@@ -1192,6 +1209,8 @@ static int atl1c_reset_mac(struct atl1c_hw *hw)
" disabled for 10ms second\n");
return -1;
}
+ AT_WRITE_REG(hw, REG_MASTER_CTRL, master_ctrl_data);
+
return 0;
}
@@ -1336,6 +1355,10 @@ static int atl1c_configure(struct atl1c_adapter *adapter)
u32 intr_modrt_data;
u32 data;
+ AT_READ_REG(hw, REG_MASTER_CTRL, &master_ctrl_data);
+ master_ctrl_data &= ~(MASTER_CTRL_TX_ITIMER_EN |
+ MASTER_CTRL_RX_ITIMER_EN |
+ MASTER_CTRL_INT_RDCLR);
/* clear interrupt status */
AT_WRITE_REG(hw, REG_ISR, 0xFFFFFFFF);
/* Clear any WOL status */
--
1.7.7
next prev parent reply other threads:[~2012-04-13 0:18 UTC|newest]
Thread overview: 45+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-04-13 0:14 [PATCH 00/37] atl1c: update hardware settings xiong
2012-04-13 0:14 ` [PATCH 01/37] atl1c: update author contact info & company/driver desciption xiong
2012-04-13 0:14 ` [PATCH 02/37] atl1c: remove multiple-RX-Q code xiong
2012-04-13 0:14 ` [PATCH 03/37] atl1c: remove HDS register xiong
2012-04-13 0:14 ` [PATCH 04/37] atl1c: remove VPD register xiong
2012-04-14 0:45 ` David Miller
2012-04-14 9:12 ` Huang, Xiong
2012-04-14 14:22 ` Ben Hutchings
2012-04-14 18:24 ` David Miller
2012-04-17 8:36 ` Huang, Xiong
2012-04-13 0:14 ` [PATCH 05/37] atl1c: remove SMB/CMB DMA related code xiong
2012-04-13 0:14 ` [PATCH 06/37] atl1c: split 2 32bit registers of TPD to 4 16bit registers xiong
2012-04-13 0:14 ` [PATCH 07/37] atl1c: remove code related to rxq 1/2/3 xiong
2012-04-13 0:14 ` [PATCH 08/37] atl1c: wrong register used to stop TXQ xiong
2012-04-13 0:14 ` [PATCH 09/37] atl1c: correct wrong definition of REG_DMA_CTRL xiong
2012-04-13 0:14 ` [PATCH 10/37] atl1c: remove dmaw_block xiong
2012-04-13 0:14 ` [PATCH 11/37] atl1c: using fixed TXQ configuration for l2cb and l1c xiong
2012-04-13 0:14 ` [PATCH 12/37] atl1c: restore max-read-request-size in Device Conrol Register xiong
2012-04-13 17:02 ` Ben Hutchings
2012-04-14 10:39 ` Huang, Xiong
2012-04-13 0:14 ` [PATCH 13/37] atl1c: threshold for ASPM is changed based on chip capability xiong
2012-04-13 0:14 ` [PATCH 14/37] atl1c: add module parameter for l1c_wait_until_idle xiong
2012-04-13 0:14 ` [PATCH 15/37] atl1c: update right threshold for TSO xiong
2012-04-13 0:14 ` [PATCH 16/37] atl1c: remove dmar_dly_cnt and dmaw_dly_cnt xiong
2012-04-13 0:14 ` [PATCH 17/37] atl1c: clear PCIE error status in atl1c_reset_pcie xiong
2012-04-13 0:14 ` [PATCH 18/37] atl1c: refine reg definition of REG_MASTER_CTRL xiong
2012-04-13 0:14 ` [PATCH 19/37] atl1c: clear bit MASTER_CTRL_CLK_SEL_DIS in atl1c_pcie_patch xiong
2012-04-13 0:14 ` [PATCH 20/37] atl1c: refine/update ASPM configuration xiong
2012-04-13 0:14 ` xiong [this message]
2012-04-13 0:14 ` [PATCH 22/37] atl1c: fix WoL(magic) issue for l2cb 1.1 xiong
2012-04-13 0:14 ` [PATCH 23/37] atl1c: remove MDIO_REG_ADDR_MASK in atl1c_mdio_read/write xiong
2012-04-13 0:14 ` [PATCH 24/37] atl1c: remove REG_PHY_STATUS xiong
2012-04-13 0:14 ` [PATCH 25/37] atl1c: refine phy-register read/write function xiong
2012-04-13 0:14 ` [PATCH 26/37] atl1c: remove PHY contrl in atl1c_reset_pcie xiong
2012-04-13 0:14 ` [PATCH 27/37] atl1c: refine SERDES-clock related code xiong
2012-04-13 0:14 ` [PATCH 28/37] atl1c: remove PHY polling from atl1c_open xiong
2012-04-13 0:14 ` [PATCH 29/37] atl1c: update PHY reset related routine xiong
2012-04-13 0:14 ` [PATCH 30/37] atl1c: remove PHY reset/init for link down event xiong
2012-04-13 0:14 ` [PATCH 31/37] atl1c: add function atl1c_power_saving xiong
2012-04-13 0:14 ` [PATCH 32/37] atl1c: refine start/enable code for MAC module xiong
2012-04-13 0:14 ` [PATCH 33/37] atl1c: add PHY link event(up/down) patch xiong
2012-04-13 0:14 ` [PATCH 34/37] atl1c: clear WoL status when reset pcie xiong
2012-04-13 0:15 ` [PATCH 35/37] atl1c: remove code of closing register writable attribution xiong
2012-04-13 0:15 ` [PATCH 36/37] atl1c: refine mac address related code xiong
2012-04-13 0:15 ` [PATCH 37/37] atl1c: cancel task when interface closed xiong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1334276102-15866-22-git-send-email-xiong@qca.qualcomm.com \
--to=xiong@qca.qualcomm.com \
--cc=davem@davemloft.net \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=nic-devel@qualcomm.com \
--cc=qca-linux-team@qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®